how to install lcd screen in car quotation

Vehicles are increasingly outfitted with a way to keep all of the passengers entertained during a road trip or give directions during a long voyage. Installing an LCD monitor in your car adds visual entertainment and practical functionality. The LCD monitor could be used for watching DVDs, playing video games, or for GPS navigation systems.

Lots of vehicle owners invest in LCD monitors intended for viewing behind the vehicle. This type of LCD monitor is known as a reverse camera monitoring system. The monitor activates when the vehicle is in reverse and lets the driver know what is behind the vehicle.

LCD monitors can be located in three places in a vehicle: the middle of the dashboard or console area, the ceiling or interior roof in SUVs or vans, or attached inside the headrest of the front seats.

The LCD monitor installed in a dashboard is usually used for navigation and video purposes. Most LCD monitors are touch screen and have a typical amount of video storage.

Most LCD monitors installed into the ceiling or interior roof of a sport utility vehicle or van are generally used for video or TV use only. Headphone jacks are generally installed near the passenger"s seat for easy access to allow passengers to hear the video footage with no distractions to the driver.

It is becoming more common to install LCD monitors inside the headrest of the front seats. These monitors are made for passengers to view movies and play games. There could be a gaming console or the LCD monitor could have preloaded games for a viewer’s choice.

Note: You may have to run your own power supply to the monitor. Be sure to hook up the power supply to a terminal or wire that has power only when the key is in the on or accessory position. To do this, you will need a DVOM (digital volt ohm meter) to check the power to a circuit with the key off and on.

Warning: Do not attempt to tap into a source of power with an object that is connected to the vehicle’s computer. If the LCD monitor were to short out internally, then it’s possible that the vehicle’s computer could short out as well.

Step 10: Pull the molding loose above the passenger doors. This allows you to locate the roof support, which is just a few inches behind the hump in the headliner.

Step 11: Use measuring tape to measure the center point of the headliner. Push firmly with your fingertips into the headliner to feel for the support bar.

Step 12: Measure from side to side of the vehicle. Once you have located the center of the support bar, then mark an X on the spot with a permanent marker on the tape.

Step 16: Straighten out a coat hanger. Attach a new wire to the coat hanger and feed it through the hole you made and out through the molding that you peeled back.

Step 17: Tap the wire into the dome light power circuit with key on only. Make sure that you use a one size larger wire to reduce heat and resistance.

Note: If you plan on using your stereo system for sound, you will need to send RCA wires from the cut hole to your glove box. This results in your having to remove the molding and peel up the carpet to the floor to hide the wires. Once the wires are at the glove box, you then can add adapters to sent it to the stereo and hook it up to the output RCA channel.

Note: If you plan on using an FM modulator, then you will need to send the power and ground wires to the modulator. Most modulators fit perfectly under the glove box next to the stereo. You can tap into the fuse box for a power supply that is active only with the key in the on or accessory position.

Put the caps on to cover the screws. If you removed any other coverings or peeled up the carpet, make sure to secure the coverings and put the carpet back into place.

Note: If you plan on using your headrest and installing a flip up or down LCD monitor, then you will need to measure the headrest and install the LCD monitor onto the headrest. Drill out 4 holes to mount the LCD bracket. You will be drilling into the headrest steel brace. Then you can mount the bracket to the headrest and install the LCD monitor onto the bracket. Most LCD monitors come pre-installed into a headrest like the one in your vehicle. Basically, you are just switching out the headrest for another one, however, it does cost more.

Note: If your seats are fully upholstered, then you must unclasp the upholstery. Fully recline the chair and locate the plastic clasp. Carefully pry on the seam to open and then carefully pry apart the plastic teeth.

Step 26: Install the headrest with the LCD monitor into the seat. You will need to feed the wires through the mounting holes on the seat’s poles into the back of the seat.

Step 27: Run wires through seat material. Once the headrest is installed, you will need to run the wires through the seat cloth or leather material to just under the seat.

Step 28: Guide the wires behind the seat’s back metal brace. This is a tight fit, so be sure to put the rubber hose on the wires directly over the location of the metal brace.

Close the seam to seal the seat together. Sit the seat back up to the normal position that it was originally in. The kit will come with a DC power jack to install the power cord to the vehicle. You have the option to hard wire the LCD monitor or use the cigarette lighter port.

Step 31: Splice into the power wire to the power seat. Be sure it is the seat that is operated only when the key is in the ignition in the on or accessory position.

If you do not have power seats, you will need to run a wire to the fuse box under the carpet in the vehicle and place it into a port that is only active when the key is in the ignition and placed on the on position or accessory position.

Step 34: Hook up the DC power jack cable to the cable sticking out of the back of the seat. Roll up the cable and zip tie the slack and DC power jack to the seat’s bracket.

Step 35: Connect the LCD monitor kit’s A/V input cable to the A/V input cable sticking out of the seat. Roll up the cable and tie it off under the seat out of the way.

Note: If you did not have a nine volt battery saver, you will have to reset all of the settings in your vehicle, like your radio, electric seats, and electric mirrors.

If you installed an LCD monitor with a dvd player, then open the monitor up and install a DVD. Verify the the dvd plays. Hook up headphones to the headphone jack on the LCD monitor or to the remote jack and test the sound. If you routed the sound through the stereo, put the stereo on the input channel and test the sound that is coming in from the LCD monitor.

If your LCD monitor does not operate after installing the LCD monitor into the vehicle, then there may be further diagnosis of the LCD monitor assembly needed.

If the problem persists, then you should seek out help from one of YourMechanic’s certified mechanics. If you have any questions about the process, be sure to Ask a Mechanic for some quick, helpful advice.

The Canadian mechanical engineering student hacked the dashboard display screen in his car, so it’s now displaying funny quotes from Reddit. Specifically, it’s displaying those weird “Shower Thoughts” — the headlines from Reddit’s forum for the brilliant one-off insights that pop into your head at random moments.

“There exists a set of finite actions that, if I performed them in the correct order, would make me a millionaire in a day. I just don’t know what they are.”

“I have no programming experience other than a few Arduino projects around the house,” De Mel wrote in a blog post, “so my code is definitely not optimal.” But within one month, he’d already finished the project, and shared its Python code on GitHub. “Hopefully, this will at least give you some kind of starting point for your own project, and you will be able to see the underlying process for making this work.”

And there is something truly inspiring about a man who dares to tinker with the software in his $20,000 Hyundai, just to make its dashboard show funny quotes from Reddit.

Luckily, all the digital devices in his 2012 Hyundai Genesis Coupe were connected using a fairly common standard — the “Controller Area Network bus” (or CAN bus). So Harin grabbed one of his Arduino’s — plus a cheap SPI CANBUS circuit board — and just started doing some experiments. When he first installed his Arduino circuit board into the dashboard, the LCD began showing the time of day — every ten milliseconds — and any new messages that he sent to the screen were simply being wiped out when the system re-transmitted. But Harin had already built up a strong motivation to keep moving forward, according to a recent write-up in Make: magazine, because “I hated that stupid little blue LCD. It would just sit there staring at me brightly with the words ‘AUX’…”

So he re-routed the LCD’s input. And fortunately, Harin’s other Raspberry Pi board could accommodate a WiFi dongle. By using an iPhone for connectivity, it was now able to draw down the funny Reddit quotes. And Make: also reported that his next project may be to install a router directly into his car.

Harin’s even mounted his Nexus 7 Android tablet into his car’s dashboard and is using it to play music. In the comments on his blog, he talks about one day transmitting the “now playing” information from the tablet to the LCD. Somewhere in the mix, there’s even an SQL database. “My main script retrieves the top post from Shower Thoughts and converts the characters to their hexadecimal equivalents, adds the message ID and row identifier, and stores it in an SQL database.”

There’re two more scripts just for retrieving the quote from the database and display it on the screen, which Harin says will be building blocks for more features down the road. “Eventually, I’ll be able to screen the messages intended for the LCD on the primary [CAN bus] network and add the ones I want to keep to the SQL database while removing the ones I don’t need anymore.”

But perhaps the most inspiring part of this project is that judging by Harin’s blog posts; he only worked on it on-and-off for over a month. “I’m a full-time student with a full-time job,” Harin wrote, “so I don’t get to tinker as much as I’d like to.”

Now instead of seeing the external temperature on his display, he sees bits of mind-blowing amateur philosophy. But maybe it goes to show you that if you’re going someplace strange, your journey there can be just as unpredictable. According to his blog post, the screen was originally intended for displaying song information (title and artist) for Sirius XM.

Because of this, the Reddit quotes were originally preceded by a musical note, and one screenshot makes it look like he’d been listening to a song titled “Being a cop must be awful…”

Standard Includes: remove & reinstall dash panel, install GPS antenna, connect wiring harness, antenna adapter, install mounting kit and running Bluetooth microphone near visor [installation parts sold separately]

vehicles may not have a flat headliner and additional labor charges will be required.[Add optional wired FM modulator $125 parts and labor sold separately]

While touch screens are handy, it definitely isn’t useful if they aren’t working. Here are a few troubleshooting steps you can take to fix the issue with your car’s touch screen:Clean your touchscreen

The cost of having a professional replace your car’s touch screen depends on what you choose as a replacement but can generally land between $100 and $300.

Once you download Jerry, just answer a handful of questions that will take you roughly 45 seconds to complete and you’ll immediately get car insurance quotes for coverage similar to your current plan. Jerry customers save an average of $887 a year.

The days of unfolding faded maps from your glove compartment are long gone. Navigation technology can be found in most cars, whether it’s a smartphone app or an in-dash system. Whether you drive an older model that doesn’t have one built-in, or you didn’t like the options when buying a newer one, you can outfit your vehicle with a navigation system that meets all your needs. Here are some tips that can help you figure out the cost of your car navigation system.

If you’re sick of using your phone to get around town, an in-dash navigation system will simplify your ride and provide a whole bunch of features that altogether make for a more enjoyable experience. The car navigation system installation and system type will decide the price.

Rates for installation range from $150 to $450 depending on where you have the service done. Generally speaking, the more complex the system, the higher the cost to install. Less frequently, a technician will charge by the hour, but it’s more common to be charged for the job.

You have the option of a factory navigation system that will fit in seamlessly with your vehicle, but it costs more. They’re designed with the car in mind, so the features are catered to the layout and interior of your vehicle, and the screen is typically larger. Plus, factory speakers are included in the warranty, should anything happen to your car. Though, if you’re looking at installing a compatible factory navigation system in a new car, you’re looking at $500 as the starting price and up to $2,000 or more.

An aftermarket navigation system is typically cheaper, and while it may not perfectly match the aesthetic of your vehicle, it often has the same capabilities and more. People who want a higher quality audio experience and an expanded functionality will be pleased with these systems that offer better and more colorful displays and features like Apple CarPlay, Android Auto, and Pandora streaming. These highly customizable navigation systems will run you from $300 to about $1,300.

Adding a navigation system to your car will improve its resale value, and it will function even if you’re outside cell service and smartphone guidance fails. If you want better sound and upgraded speakers, an aftermarket nav system will get you that boost in audio quality.

When you purchase a car navigation system in Hayward, CA, look no further than Autohaus Automotive Solutions. Not only do they offer a comprehensive selection of excellent aftermarket navigation systems from Alpine and Kenwood, but they also offer professional car navigation installation services in Hayward and treat you like family. Visit Autohaus Automotive today or make contact us with any questions to find out how to improve your driving experience.

ar stereos with screens the size of tablets have arrived at Crutchfield, and that’s good news for more car owners than ever. If you’ve been craving a big screen stereo for easy source selection while driving, car audio legends like Alpine, Pioneer, Sony, Kenwood, and more offer some seriously sleek solutions.

There’s a lot to be excited about when it comes to car stereos with oversized touchscreen displays. Striking resolution and responsive control make these stereos a joy to use. Plus, built-in essentials for smartphone integration and voice control like Apple CarPlay® and Android Auto™ look great on a big screen. But the most satisfying development here is that most of these car stereos fit dash openings that previously couldn’t accommodate touchscreen receivers. Use our vehicle fit tool to explore your options.

Because the touchscreen display of these special stereos "floats" in front of your dash, it’s important to evaluate the layout of your air vents and any other controls around where your radio lives. No dash layout is the same. So, car stereos with oversized screens, like the Sony shown below, prioritize adjustability.

When you install your stereo, you"ll have angle, depth, and height adjustability so you can secure the perfect fit. It"s important to note that these adjustments must be done before your stereo is affixed to any dash kit you"ll be using. You won"t be able to easily adjust it after the fact, so you"ll want to think about the layout as you do the installation.

Jensen"s CAR110X digital media receiver offers nice compatibility with your smartphone for the most affordable price tag in this category. You"ll get Apple CarPlay and Android Auto compatibility, USB inputs for phone charging, and 4-volt preamp outputs to incorporate an aftermarket amp and build a solid system — all with a 10.1" touchscreen display.

I"ve always enjoyed Sony"s approach to digital multimedia receivers. Their streamlined menus and layout make selecting sources and adjusting settings downright breezy. Their XAV-AX8100 brings that same thinking to a 8.95" screen. With 20 watts RMS of built-in power, 5-volt preamp outputs for system-building, awesome smartphone integration, and a 3-year warranty, Sony"s entry into the oversized category offers a whole lot of bang for your buck.

In the case of their DMH-WT8600NEX, the 10.1" capacitive HD touchscreen display looks gorgeous. And as you"d expect, Pioneer builds in excellent audio controls and loads of features, including Amazon Alexa compatibility and inputs for two cameras. I previewed Pioneer"s other stereos in this series and was impressed by the sturdiness and striking beauty of their displays as well.

If you"re not quite ready for the 10.1" display, Pioneer offers stereos car stereos with 8" and 9" floating displays as well as models that are ideal for custom installations.

Alpine has always taken great strides to bring awesome features to popular vehicles, and their Halo9 Series forged a path for all receivers to follow, offering the first oversized display of its kind and customizing it for vehicle-specific use.

And if that"s not big enough, Alpine equipped their newest Halo receiver — the stunning ILX-F411 — with an 11" screen! The ILX-F411 lets you customize your display, but you"ll lose HD Radio® compatibility, the ability to add Alpine"s Truck Accessory Controller, and certain interface controls only available on the ILX-F309.

No surprise that JVC"s KW-Z1000W digital multimedia receiver with a 10.1" screen is a solid entry in the category. If you"re adding an aftermarket amplifier, speakers, and sub, you"ll want to give this one serious consideration. 5-volt preamp outputs for a powerfully clean audio signal, a 13-band EQ, time alignment, and K2 sound-enhancement technology let you make sound-tweaking a priority.

Kenwood"s Excelon Reference MXD1057XR digital multimedia receiver is the real deal. Upgrade to a 10.1" floating display with built-in HD Radio, Apple CarPlay, Android Auto, support of high-res audio, and the confidence that comes with a 2-year warranty. Kenwood gives you the tools to customize your homescreen with essential sources and tools. Plus, you get a good ol" fashioned volume knob!

If you need help determining if a floating screen car stereo is right for you, give our Advisors a call. You can also confirm fit for any of the above stereos by using our vehicle selector.

We can custom install just about anything you can think of including dvd players,  LCD monitors, amplifiers, sub woofer enclosures, body kits, alarms and so much more!

Car Stereo Systems has all of the parts and accessories you will need for any make or model of car.We install everything we sell and we employ some of the best craftsmen in the industry to guarantee that you will be satisfied with our work. We specialize in custom installation stereo systems.

Car Stereo Systems has built a reputation in Falls Church based on hard work, honesty, and integrity and we work hard every day to live up to and maintain that reputation. Our shop is locally owned and operated and we offer a wide selection of products at great prices. You can count on the fact that all the technicians that work on your vehicle take as much pride in their work as you do in your vehicle. If you don’t see what you are looking for, ask us about special orders.

When you need the ultimate in real estate, look no further than the Sony XAV-AX8100. Last year, its sister model, the AX8000, made this list but since then there have been even more improvements. First off, this unit has a massive 8.95” touchscreen, yet it fits a single DIN 2” opening. The clever design allows this massive monster to fit in so many more vehicles than a traditional 2 DIN opening. It is an outstanding upgrade for older vehicles once thought to be limited on touch screen stereo upgrades.

The biggest difference to highlight between the AX8100 and its predecessor, the AX8000 is that the AX8100 now comes with an HDMI input. This allows you to simply plug in ANY multimedia device that you want and play video directly on the head unit. Xbox, Playstation, Switch, or even your iPhone with an HDMI adapter – this HDMI input is a HUGE upgrade and really opens this unit up as a super powerful multimedia head unit. Additionally, it is also preloaded with Android Auto and Apple CarPlay for a seamless music experience. It has one of the lowest glare screens we have ever tested as well. Simple, easily understandable icons help drivers stay focused on the road and not on searching for features they want.

The nearly 9” touch sensitive screen appears to hover above your dash when installed. The screen can be tilted to accommodate different angles and to provide a comfortable viewing angle for the driver. The simple, matte-finish look blends in nicely with many different vehicle interiors and gives a true high-end feel to any car or truck. The AX8000 is an instant upgrade for almost any car on the road today.

The AX8100 features a peak of 55 watts per channel and has five, 5V pre outs for even more expandability. The unit is factory-prepared for a single backup camera. A single rear USB port can be used for wired connections and provides a 1.5a charging point for your smartphone.

As Android-powered smartphones gain more market share, Google is attempting to match the runaway success of the Apple CarPlay format with some strong plays of its own.

The upgrade brought new app connectivity, greater integration with Google Maps and the related Waze map app, as well as Google’s own music app Play, plus Spotify, Messenger, podcast apps and many more.

This is great if your car can connected to Android Auto. But if your ride is a few years old, it’s likely your multimedia system may not be ready for smartphone mirroring. Sure, you might have Bluetooth, but unless you can see a screen pop up you don’t have it out of the box.

If you’re about to update your car, then odds are that it’ll offer smartphone mirroring – it’s available on cars as cheap as the entry level Kia Picanto. If, however, you’re keeping your car for another couple of years yet, there are a couple of sneaky ways to get Android Auto on board your rig.

Back in the day, the savvy automotive audiophile would swap the standard AM/FM radio in their car for one with a cassette deck, or even a CD player. And if you were really cashed up, a ten-disc CD changer in the boot was the duck’s guts.

The job of swapping head units, though, has become much more difficult over the years, as car makers redesigned centre consoles and dashboards to better integrate newer screen-based multimedia systems.

However, there are still a lot of cars out there that still use the simpler DIN style of installation, which allows a new head unit to simply slot into a pre-existing hole.

DIN is named after the German standards body that defined a DIN slot as being two inches by eight inches, or 5cm by 20cm. This meant that all cars would be equipped with a universally standard-sized radio unit.

However, if your car has a more integrated system, modern installers have worked out ways to retrofit a system that can run Android Auto and make it look factory.

‘It’s the most common job we do these days,’ said Clinton Venaglia, who owns InCar Installations in the southern NSW city of Wollongong. ‘Some brands like Ford and Holden really headed down the integrated path a few years ago, but even so we can still install a system in most modern cars.’

Toyota, for example, makes things relatively simple by using double-DIN (think two DINs stacked on top of each other), while Mazda is a little more difficult.

Integrating systems like reversing cameras into the new units isn’t a problem either, according to Vengalia, who estimates the average cost of adding an Android Auto system to a car is around £400.

A new Android Auto head unit is generally based around a colour touch screen that’s built into the unit. It either remains in place permanently, or folds away and retracts into the dash for greater security and a cleaner look.

While home installation of an Android Auto system isn’t especially difficult for technically savvy types, we would highly recommend that a professional installer does the work. It’s all too easy, for example, to leave off a crucial earthing strap or not have the correct wiring module to make your new head unit work properly with your car.

As well, not all head units are compatible with all cars. You might lose the ability to control your stereo from your steering wheel controls, for example. It will cost a bit more, but a reputable installer will more likely help you if something goes wrong down in the future.

Some car makers that have lagged behind Android Auto integration are attacking the issue head on by offering a retrofit kit to give owners the full Android Auto experience.

The most recent update to the CX-9 was the first mainstream Mazda to get Android Auto as standard; the BT-50 ute scored it first because of its connection with the Ford Ranger.

‘It will be available for all customers with an MZD Connect system that first went on sale with Mazda 3 in early 2014,’ said a Mazda spokesperson last year.

Hyundai, too, has offered software upgrades for owners of their cars in order for them to access Android Auto. However, it hasn’t been the smoothest of rollouts.

Hyundai i30s from 2015 were largely able to accept the upgrade, but conversely, owners of top spec SUVs like the Santa Fe and Tucson Highlander have been told that the in-built GPS system aboard their cars prevent the installation of the Android Auto system.

Is your car too old to be retrofitted Android Auto? Then Bluetooth connectivity will still allow you to stream music and podcasts through the car speakers. As well, map apps like Google Maps will send audible instructions over the sound system if you’re listening to streaming music.

However, more and more phones are being produced without the 3.5mm headphone jack, which means it’s Bluetooth, Android Auto or the good old FM airwaves.

Electronic upgrades come in varying degrees of difficulty. Some are "so simple that even a child could do it," while others require a degree in advanced automotive electronics. So what"s an example of a relatively easy installation?

The simplest installations actually involve no real installation at all. Some small devices, like satellite radio receivers and some radar detectors, simply need to be placed on top of the dashboard or affixed to the inside of the windshield. Usually these devices will come with some means of attaching them to the dashboard or windshield surface -- a suction cup, for instance, or an adhesive strip. Some in-car DVD players clip on a headrest or even a sun visor. Audio devices will also need to be interfaced with your vehicle"s audio system.

If you have an older car that"s equipped with a cassette player, yet you want to listen to CD-or MP3-quality sound, you do have options. A simulated cassette with a cable on one end can extend from your old car radio the device. The cassette adapter will play the audio signal through your vehicle"s audio system as though it were a tape. But what if you don"t even have a cassette deck as an option? A small FM radio transmitter (available from many electronics retailers) can broadcast the signal from the portable device to your car"s antenna. Another option is a small cable that can interface the portable device with the radio"s AUX jack or you may be able to use a USB cable, if your stereo supports it. If all goes well, installing such devices can take only a few minutes and the only danger is that the adhesive strip might mar the dashboard surface.

But not every installation goes exactly as planned. In fact, if you ask just about anyone that regularly tackles an automotive electronics upgrade they"ll let you know that it"s wise to expect the unexpected. Read the next page for a small sample of things that can go wrong.

If you"re in the market for new entertainment electronics in your car, you have a lot of decisions to make. The following list includes a few of the more popular upgrades:

Multi-CD Changers: A CD changer lets you keep several CDs simultaneously on tap so that you don"t have to juggle discs while driving. Most CD changers are mounted in the trunk or installed under the front seat.

iPod Docks: Why carry around dozens of CDs when you already have hundreds of albums stored on your iPod? An iPod dock makes it easy to connect your iPod to your car"s audio system.

Bluetooth Hands-free Kits: Most jurisdictions make it illegal to drive while talking on a cell phone. If you have a Bluetooth-enabled phone, a Bluetooth hands-free kit routes your calls through your car"s audio system and in most cases will provide voice dialing (if supported by your phone).

DVD Players with LCD Display: The place you"re most likely to want to install video is for backseat passengers. If that"s what you want, companies like Sony and Kenwood will be happy to provide the systems.