how to install lcd screen in car for sale

Vehicles are increasingly outfitted with a way to keep all of the passengers entertained during a road trip or give directions during a long voyage. Installing an LCD monitor in your car adds visual entertainment and practical functionality. The LCD monitor could be used for watching DVDs, playing video games, or for GPS navigation systems.

Lots of vehicle owners invest in LCD monitors intended for viewing behind the vehicle. This type of LCD monitor is known as a reverse camera monitoring system. The monitor activates when the vehicle is in reverse and lets the driver know what is behind the vehicle.

LCD monitors can be located in three places in a vehicle: the middle of the dashboard or console area, the ceiling or interior roof in SUVs or vans, or attached inside the headrest of the front seats.

The LCD monitor installed in a dashboard is usually used for navigation and video purposes. Most LCD monitors are touch screen and have a typical amount of video storage.

Most LCD monitors installed into the ceiling or interior roof of a sport utility vehicle or van are generally used for video or TV use only. Headphone jacks are generally installed near the passenger"s seat for easy access to allow passengers to hear the video footage with no distractions to the driver.

It is becoming more common to install LCD monitors inside the headrest of the front seats. These monitors are made for passengers to view movies and play games. There could be a gaming console or the LCD monitor could have preloaded games for a viewer’s choice.

Note: You may have to run your own power supply to the monitor. Be sure to hook up the power supply to a terminal or wire that has power only when the key is in the on or accessory position. To do this, you will need a DVOM (digital volt ohm meter) to check the power to a circuit with the key off and on.

Warning: Do not attempt to tap into a source of power with an object that is connected to the vehicle’s computer. If the LCD monitor were to short out internally, then it’s possible that the vehicle’s computer could short out as well.

Step 10: Pull the molding loose above the passenger doors. This allows you to locate the roof support, which is just a few inches behind the hump in the headliner.

Step 11: Use measuring tape to measure the center point of the headliner. Push firmly with your fingertips into the headliner to feel for the support bar.

Step 12: Measure from side to side of the vehicle. Once you have located the center of the support bar, then mark an X on the spot with a permanent marker on the tape.

Step 16: Straighten out a coat hanger. Attach a new wire to the coat hanger and feed it through the hole you made and out through the molding that you peeled back.

Step 17: Tap the wire into the dome light power circuit with key on only. Make sure that you use a one size larger wire to reduce heat and resistance.

Note: If you plan on using your stereo system for sound, you will need to send RCA wires from the cut hole to your glove box. This results in your having to remove the molding and peel up the carpet to the floor to hide the wires. Once the wires are at the glove box, you then can add adapters to sent it to the stereo and hook it up to the output RCA channel.

Note: If you plan on using an FM modulator, then you will need to send the power and ground wires to the modulator. Most modulators fit perfectly under the glove box next to the stereo. You can tap into the fuse box for a power supply that is active only with the key in the on or accessory position.

Put the caps on to cover the screws. If you removed any other coverings or peeled up the carpet, make sure to secure the coverings and put the carpet back into place.

Note: If you plan on using your headrest and installing a flip up or down LCD monitor, then you will need to measure the headrest and install the LCD monitor onto the headrest. Drill out 4 holes to mount the LCD bracket. You will be drilling into the headrest steel brace. Then you can mount the bracket to the headrest and install the LCD monitor onto the bracket. Most LCD monitors come pre-installed into a headrest like the one in your vehicle. Basically, you are just switching out the headrest for another one, however, it does cost more.

Note: If your seats are fully upholstered, then you must unclasp the upholstery. Fully recline the chair and locate the plastic clasp. Carefully pry on the seam to open and then carefully pry apart the plastic teeth.

Step 26: Install the headrest with the LCD monitor into the seat. You will need to feed the wires through the mounting holes on the seat’s poles into the back of the seat.

Step 27: Run wires through seat material. Once the headrest is installed, you will need to run the wires through the seat cloth or leather material to just under the seat.

Step 28: Guide the wires behind the seat’s back metal brace. This is a tight fit, so be sure to put the rubber hose on the wires directly over the location of the metal brace.

Close the seam to seal the seat together. Sit the seat back up to the normal position that it was originally in. The kit will come with a DC power jack to install the power cord to the vehicle. You have the option to hard wire the LCD monitor or use the cigarette lighter port.

Step 31: Splice into the power wire to the power seat. Be sure it is the seat that is operated only when the key is in the ignition in the on or accessory position.

If you do not have power seats, you will need to run a wire to the fuse box under the carpet in the vehicle and place it into a port that is only active when the key is in the ignition and placed on the on position or accessory position.

Step 34: Hook up the DC power jack cable to the cable sticking out of the back of the seat. Roll up the cable and zip tie the slack and DC power jack to the seat’s bracket.

Step 35: Connect the LCD monitor kit’s A/V input cable to the A/V input cable sticking out of the seat. Roll up the cable and tie it off under the seat out of the way.

Note: If you did not have a nine volt battery saver, you will have to reset all of the settings in your vehicle, like your radio, electric seats, and electric mirrors.

If you installed an LCD monitor with a dvd player, then open the monitor up and install a DVD. Verify the the dvd plays. Hook up headphones to the headphone jack on the LCD monitor or to the remote jack and test the sound. If you routed the sound through the stereo, put the stereo on the input channel and test the sound that is coming in from the LCD monitor.

If your LCD monitor does not operate after installing the LCD monitor into the vehicle, then there may be further diagnosis of the LCD monitor assembly needed.

If the problem persists, then you should seek out help from one of YourMechanic’s certified mechanics. If you have any questions about the process, be sure to Ask a Mechanic for some quick, helpful advice.

Make a detailed plan. It is important to begin organized with all of the necessary equipment, rather than to start installing and realize later that more tools are needed.

Replace the in-dash radio that controls the car system, known as the head unit. It is vital to make sure that the new head unit is the correct size for the vehicle. Head units come in sizes of single-din, which is a 180 by 50 mm panel, or double-din, which is a 180 by 100 mm panel.

Unscrew any set screws or hex bolts that secure the fairing to remove the dashboard pieces around the radio, then cautiously pull out the dashboard pieces.

Disconnect the radio"s antenna connection and place aside the old head unit. Don"t throw away the old head unit, though, because to sell the car in the future, the stock radio will need to be re-installed so you can keep the new touch screen stereo.

Connect the antenna cable and put in the new head unit. Turn on the car to check if the connections work properly. If they do, then screw the new radio into place and connect the audio/visual cable to the touch screen monitor. If the radio does not turn on, however, then it is like a faulty splice in the wire harness. To fix this, remove the radio and check all of the connections.

This website is using a security service to protect itself from online attacks. The action you just performed triggered the security solution. There are several actions that could trigger this block including submitting a certain word or phrase, a SQL command or malformed data.

Has your car"s touch screen stopped working? Or has it developed an issue where it does not respond correctly to your touch? You may be hesitant to have it replaced because of the cost of labor. If you"re here, you may be wondering if you can take care of the touch screen radio replacement yourself.

Many touch screen radios (such as the Cadillac CUE radio) are plug-and-play devices. So when you replace those parts, all you need to do is remove the old one, plug in the new one, and then secure it in place. It"s not that complicated. Yet, it"s a good idea to look up the installation instructions first to make sure that it"s a job you can handle. It should be an easy and straightforward process in most vehicles.

If you want your touch screen replacement to go smoothly, always get an OEM or OE-quality replacement touch screen. We cannot stress how important this is.

Aftermarket touch screens don"t have the same level of quality as OEM touch screens. OEM and good OE-quality touch screens are made with high quality materials that will last a long time.

With an OEM or OE-quality touch screen, you don"t have to worry about fitment or compatibility issues. OEM and OE-quality touch screens are made for your make and model. That means they have the right dimensions. If there"s one thing that makes installing a touch screen much easier, it"s proper fitment.

Most aftermarket radio replacement parts aren"t designed to fit your specific make and model. Many of them come with universal dimensions made for a wide range of cars. Chances are low a universal aftermarket touch screen will fit your vehicle without any issues.

A new touch screen needs to match the car"s electrical system to work properly, too. An OEM or OE-quality touch screen will do this. It will come with the right connectors and the wiring harnesses will all be the correct length. You can"t say the same about aftermarket touch screens.

It"s more than just fitment. It"s also about the way the touch screen feels to use. OEM and OE-quality touch screens are sensitive enough to respond to very light touches. They"re more reliable over time, too. They don"t become less responsive like aftermarket touch screens do.

If you"re looking for a replacement touch screen for your vehicle, ISS Automotive may have what you need. We offer OE-quality replacement radios and screens. When we remanufacture OEM touch screens, we use OEM and OE-quality replacement parts. We have been around for over 70 years, so we know car radios and touch screens inside and out.

Eonon official website: https://www.eonon.com/ Facebook: https://www.facebook.com/Eonon.Official/Twitter: https://twitter.com/EononOfficialInstagram: https:/...

If you have a smartphone and a head unit it’s obvious that you want to watch your favorite stuff on abigger screen and this is what I will help you with.

Before you start watching any movies while you are parked (right? you are parked) you need to convert the video to a specific format so you can see it in your car.

After you have plugged in the USB you might need to hit the Media Source button a few times to locate the USB. Also some cars require that your car to be stationary with the handbrake engaged. While other cars the movie is playing if the handbrake is disengaged and it only delivers the audio.

These days, people have the entire world on their phones. From messaging and staying connected to the people in your life and the world at large, the phone is a repository of several videos and multimedia elements.

It is only natural that one would want to stream something from their phone on the car screen when they are on the move. The two of the most important ways of streaming video from phone to car include USB ports and aux cables.

Car stereo systems are equipped with USB ports that allow you to connect your phone to the car’s stereo system, giving you a range of stuff to choose from when it comes to streaming.

Save all the data that you want to see on your car screen effectively on a USB port. This is the tool that you will be using to connect to your car’s stereo for streaming later.

Aux cables are one of the most commonly used tools for streaming videos, audio and music videos and movies on your car. Anything that is there on the phone can be mirrored onto your car’s stereo.

The biggest benefit of using aux cables is that you don’t have to go through the trouble of saving something on the cable. You just need to connect your aux cable to the phone and enjoy seamless streaming on your car screen. It is simple, effective and immensely popular. And now you know why!

If you are into watching and enjoying local broadcast television and have something important to watch while on the move, there is good news. There is a way you can watch videos on car screen easily without any hassles.

The installation might be slightly troublesome but it is worth the hassle if you really want to watch something. There are a number of requirements that you need to put in place should you decide to go ahead with the setup. These include an antenna, tuner and a display.

Similarly, if you wish to broadcast satellite television in your car, you need to buy a mobile antenna and a paid subscription to the service you want to stream. Though people have this in their homes, it can also be installed in cars. It is a wireless system that also gives it an edge over broadcast TV.

If you wish to play music videos in your car’s stereo, you can use some other options to do this if the above-discussed options do not appeal to you or are not working for some reason.

Bluetooth: All smartphones come equipped with Bluetooth and that makes multimedia sharing easier and simpler. Pairing devices with Bluetooth is simple and can be done in a fraction of a second.Hence, if you wish to stream a movie or music video on your car screen, you simply need to pair your phone’s Bluetooth with that of the car’s and stream whatever you wish to.

SD or Memory Card: This is one of the oldest ways of streaming audio or video on your car screen. But you would have to check if your car stereo is equipped with a card reader.If it is, all you need to do is to connect your card reader to your car’s stereo and stream anything that you want.

Car screens come in myriad shapes and sizes. If you are looking for an ultimate streaming experience, you can use the LED screen of your car for streaming multimedia.

Head Units: These are equipped for watching videos and several even have a touch feature that makes changing stuff easier and simpler and certainly faster. This is why it is one of the key features people look out for while buying or upgrading their car stereo.

Roof Fittings: Sometimes screens are fitted on the roofs of the car. These are adjustable and you can move them as you please for a seamless streaming experience.

In most cars, the head unit is equipped with DVD and CD elements and once you play them, you can watch movies on your car screen. Combination units are also adept at helping you watch movies on your car screen.

You need to put the CDs and DVDs in the combination unit set and they will stream the video for you, giving you a great experience. This is how to watch movies on car screen.

It is very convenient to play movies and music videos on your car screen if you make use of some of the most commonly available tools such as aux, Bluetooth and memory cards among others. There are several options available and you may choose as you please.

A word of caution though, you need to follow all the laws and take necessary precautions while streaming and driving simultaneously. Do not get too engrossed in watching the video that you end up in an accident.

Install Android Auto Apps Downloaded which is the simplest way to play video from any android phone to the screen of your car. You won’t require a PC nor you have to ROOT your phone. Within the app you install Fermata Auto and you’re set to enjoy videos on the big screen.

If you have an iPhone you can use the app called CarBridge. After installing it you will be able to play any video from your phone on the car screen. For Android there’s Android Auto Apps Downloaded (AAAP) after install all you need to do is within the app install Fermata Auto and you can enjoy your videos.

You can play videos on your car screen from your mobile either by using a mirroring app. What plays on your mobile is shown on the car screen. Or you get a special app that allows you to watch videos without mirroring it’s called Android Auto Apps Downloaded (AAAP) after install all you need to do is within the app install Fermata Auto and you’re set.

To watch movies on your car screen all you have to do is connect your phone via USB to the car or the USB stick to the car. With the phone you can either mirror your screen or use the head units built in apps.

All you need is to install the app called Android Auto Apps Downloaded (AAAP) after install all you need to do is within the app install Fermata Auto. Full Disclaimer you shouldn’t be watching videos while driving and this is for educational purposes only.

Yes you can play videos on your car screen. For that you need a decent head unit plus either a phone or a USB device. Additionally you might need a software to help you play videos on car screen or watch movies in car.

The easiest way to play video on Android Auto is to install the AAAD app to download and install third-party video playback apps that will work with Android Auto. I highly recommend the app called Fermata Auto.

For Androids, the best way to play videos is by installing the AAAD app. This app allows you to download Android Auto third-party apps and correctly install them. It also grants you full access to all the features of the built-in touch screen in your car. I highly recommend the app called Fermata Auto.

Many people think that touch screens are only for expensive luxury cars. But, of course, this is not true, and the fact is, these unique devices that bring the digital world to your fingertips are relatively cheap and easy to install.

As a general rule, depending on the space available in your dashboard, you will either fit a Single DIN or Double DIN touch screen. The upgrade to the touch screen includes:

From their sizes to their price, if they will fit in your old car, the tools you will need, and more. I will also share my top picks on the market to make your choice a little easier.

Days are gone where you only could have a radio with a CD player, and perhaps if you are lucky enough, a USB port so you can plug your phone in and listen to your favorite tunes.

Nowadays, many cars come with an infotainment system toped off to include all the bells and whistles. This means you get a touch screen, navigation, streaming services, and other apps.

Some infotainment systems even include Android Auto and Apple CarPlay, where you can sync your phones and set up your infotainment system to cater to your every in-car need.

However, many people still think that the radio in their car is all they can have, and no additional features or even replacements can be fitted without costing hundreds of dollars if not thousands.

Cars nowadays are designed with standards in mind. This means that for the most part, if you are driving a regular vehicle, the dashboard and radio unit is built to a specific size.

Of course, this does not mean that every car is the same, but for the most part, you can find a replacement radio, touch screen (infotainment system) that will fit your vehicle.

There are two types of touch screen sizes (infotainment systems) designed to fit either a vehicle with a large dashboard opening for radio (2 DIN) or a small opening (Single-DIN).

Furthermore, if the touchscreen does not precisely fit, you are more than likely able to find a stereo installation kit that includes a bracket for the specific make and model of your car.

Most vehicles will be expected to have the size, but if they don’t, you can always find a stereo installation kit that will help you install this size head unit.

Again this is the standard, and more than likely, your car, if it is equipped with a Double DIN unit, will be this size, and if not, you can always find a stereo installation kit.

They are renowned for their car audio expertise and will surely help you find what you are looking for regarding any car audio situation you find yourself struggling with.

If your car has a Single DIN slot, you can purchase touchscreens that fold in and out, and if you have space available for a Double DIN unit, you need to worry even less because you will have even more options to choose from.

If you do not want to go too expensive, a fantastic choice of the Single DIN unit with touch screen is the Jensen CNN 10 with its fully adjustable 10.1″ screen. If you want to try it in your car, check the latest price on Amazon.

If you plan to take it into a car audio installation shop, you have to add the price for labor, which can be as little as $125 and can go as high as $400.

If you are planning to do a DIY installation of the unit yourself, you are only looking at the unit’s price and the tools you will require, and your time.

The tools you need may vary depending on the model of your car and your dashboard, but for most instances and 90% of the time, you will most likely require these tools or slight variations of them.

I guess you have the majority of these tools in your garage, and if not, I added below Amazon links to tools I use, and I am happy with their quality.

Take note that the touchscreen size won’t matter. This is because your touch screen will either be a Single DIN unit or a Double DIN unit depending on how much space you have in your dashboard.

Take note that before you begin the process, I will explain all steps as universal, and you should be able to apply this process to almost any vehicle.

The first thing you will need to do is disconnect the battery. You want to do this because you do not wish to have power flowing through the vehicle. This is in case you short out a wire or pop fuses which could lead to all sorts of nightmares.

The next step is to remove the radio that is currently in your vehicle. You will do this by removing the dashboard panel. The main thing to remember here is finding where the panels are screwed or bolted to the car’s frame. These can be in various places depending on your vehicle, but they should be easy to find for the most part.

You will typically start at the bottom of your dashboard and work your way up unscrewing and using the pry tools to dislodge the panel from the frame.

Once you have the panel removed, you will typically find that the radio is screwed into place by a couple of 10mm screws (this may vary depending on the vehicle). This can also depend if your radio is still the factory radio or you have had an aftermarket one put in place.

This step is easier than you think because all car radios have the same color scheme for their wiring. All you need to do is match up the wires for each harness and either sell them together or use the butt plugs and crimp tool to secure them.

For a Single DIN unit, the installation is a tad bit different. A Double DIN unit will come with mounts or brackets, but a Single DIN unit will come with a cage, and you will need to put the cage and frames together.

If you prefer a visual explanation, check out a short video below, where guys from Sonic Electronix will drive you through the whole installation process in detail.

Why? It has a large 9″ WVGA capacitive touchscreen that ‘floats’ in front of the dash. The best thing about this radio is that you can adjust the mounting angle and height of the screen for the best position.

On top of the excellent touch screen, AlpineiLX-F309 can support a range of audio playback features like Bluetooth, HD radio, or SiriusXM satellite radio.

You can also choose to buy this option bundled with a front and rear camera and connecting equipment for a complete audio and camera integration for your car.

You cannot go wrong with this one. It has all of the features you can expect, like Bluetooth and Android Auto, and comes with a range of other desirable functions, such as the JVC Streaming DJ feature, which allowsup to five paired smartphones to control music streaming.

Touch screen radios are not only available to people who can afford high-end luxury or sports cars like years ago, but to anyone who drives a vehicle with a radio can install a touch screen stereo.

Contrary to mainstream thinking, these units come in sizes that will typically fit your car, and if not, there is always an installation kit that you can find for your car make and model.

All of us have a tendency to treat the driver"s seat as our personal throne. That"s where we"re in our element, so we get comfortable—and complacent. Whether our fingers were last tapping on our phone screen, grasping the handle of a wrench, or carefully unwrapping a half-melted Hershey bar, we all tend to jump in, tune the radio, adjust the AC, and set a destination on the nav screen—all without first washing our hands.

And if you have a family? Other drivers use the car and its touchscreen, too. Of course, kids can"t resist touching any kind of screen, ever, and who knows where those tiny fingers have been? All parents have swiped their car"s touchscreen and felt... mystery muck. Yuck.

Touchscreens are likely one of the dirtiest, most germ-covered surfaces of any automobile. Sure, your dash gets dusty and your floorboard accumulates (a disturbing amount of) trash. However, it"s that dash-mounted screen that gets the most fingers, and therefore germs, on it.

Not necessarily. Many typical household glass cleaners contain either ammonia or alcohol. Most manufacturers recommend avoiding harsh chemicals on touchscreens, as they can affect functionality and perhaps damage the surrounding dashboard.

Sure, it"s cheaper and easier to use plain ol" Windex or Glass Plus, mainly because you"ve probably already got that stuff. Despite the temptation, though, you should avoid using household glass cleaner on your car"s touchscreen unless you"re positive the one you"re using contains neither ammonia nor alcohol. Besides, you may already own a great screen cleaner and not realize it.

Many modern automotive detailing products, including Chemical Guys Interior Cleaner and Meguiar"s Total Interior Detailer, are safe and effective to use on your car"s touchscreen. Read the label to be sure.

The fact is, there"s an even less expensive method to clean your car"s touchscreen, no products required—except a microfiber towel. (Again, you want to avoid scraping dust particles across the surface of your touchscreen to prevent scratches, so always use a clean microfiber towel.)

Many of the experts and gearheads in our Hearst Autos test garage told us they rarely use any kind of cleaner on their personal touchscreens. Up and down the line, those who saw us testing and photographing screen cleaners—we"re talking about people whose opinions we trust and whose bylines our readers know and respect—told us that whenever they get behind the wheel, they just drip a bit of water onto a clean microfiber towel, and wipe. Done.

As a parent, however, I"m left asking the question: Will a simple water wipe eliminate germs in the family SUV? Yeah, no. Sorry, but knowing my children, and the impressive but disgusting level of filth they can achieve, I"m going to use a cleaning agent on my car"s touchscreen.

To get to the bottom of whether car screen cleaners were truly necessary, we used a very scientific methodology. That is, we got our fingers and hands dirty, and touched the heck out of a screen in a test vehicle in the Hearst Autos stable. We let it dry for a while, and then cleaned it according to the product"s instructions. We did that five times.

We first made sure all the products did the job they claimed to do—and they all did. The wipes left droplets on the screen, which required a second wipe with a microfiber. But they all cleaned the chocolate and grease off the screen, leaving it clean and clear.

While using, we looked for any greasy film or residue left behind. We also considered any particularly strong odors, and took note of cleaners that left residual streaks. Most did, but all came away clean with a soft buff—that is to say, a few more gentle wipes with the microfiber towel.

Word to the wise: Don"t discount a screen cleaner because it leaves streaks on your screen. Take your time and do it right. We noticed far too many people online complaining that the product they used wasn"t some sort of magical solution that cleaned perfectly with just one wipe. All screen cleaners—all glass cleaners, really—will streak unless you take the time and care to give the surface a soft buff at the end of the process.

With a combined 206 years of automotive publishing experience, Hearst Autos—Car and Driver, Road & Track, and Autoweek—knows cars better than just about anyone. The Gear Team is committed to delivering honest evaluations, hands-on tests, and product reviews driven by decades of knowledge and experience. We get our hands on almost every product, tool, and piece of gear we feature.

If we can’t get our hands on the gear, we rely on the combined wisdom of our writers and editors, as well as auto experts we trust. We’ll never say anything is “the best” if we wouldn’t recommend it to our friends or buy it ourselves, and we won’t claim we’ve tested something if we haven’t. Learn more about our product testing here.

Whether you"re commuting, running errands, traveling on vacation, or just backing out of your driveway, knowing exactly what"s behind you is important for safety. A rear-view or back-up camera and monitor can help to protect your car, your person, your passengers, and pedestrians. Here are some tips for choosing TFT (thin-film transistor) LCD video monitors and cameras to provide a field of vision that can enhance your peace of mind behind the wheel.

Some kits come with just a waterproof rear-view camera with night vision, without any type of monitor. These can be plugged into a DVD player, a monitor you purchase separately, or an existing display unit in your car. Other kits will come with both a rear-view camera and a TFT LCD monitor of some kind, while other kits will only offer a monitor without the backup camera. Some kits come with multiple cameras for larger vehicles and can even include a multiview display so you can see what the entire camera system is seeing at once. Which kit you choose will depend on your individual needs and the size of your vehicle.

In many cases, you can install a rear view camera and 7-inch LCD monitor yourself. This depends on whether you already have a monitor of some kind installed in your car, or if you choose a monitor that simply mounts on the dash or a wireless monitor. If the monitor needs to be installed in the dash and wired into the electrical system; however, you may need professional installation. Many backup cameras simply screw onto your license plate with existing screws and take little time to install. Some cameras are also wireless and will beam the image straight to a Bluetooth wireless monitor.

There are several different types of monitors you can pair with your back-up camera. Some monitors will simply mount on your dash and can be plugged into a 12V socket in your car. Other monitors actually take the place of your rear-view mirror, turning it into a full-time monitor. Other monitors need to actually be mounted into your dash and can take the place of an existing radio, audio unit, or touch-screen device. Kits are made to fit RV trucks and buses as well as cars.