2.2 spi tft display module 240x320 ili9341 free sample

The ILI9341 TFT module contains a display controller with the same name: ILI9341. It’s a color display that uses SPI interface protocol and requires 4 or 5 control pins, it’s low cost and easy to use. The resolution of this TFT display is 240 x 320 which means it has 76800 pixels. This module works with 3.3V only and it doesn’t support 5V (not 5V tolerant).

The ILI9341 TFT display board which is shown in the circuit diagram above has 14 pins, the first 9 pins are for the display and the other 5 pins are for the touch module.

So, the display side pins which numbered from 1 to 9 are (from left to right): VCC (5V), GND (ground), CS (chip select), RST (reset), DC (or D/C: data/command), MOSI (or SDI), SCK (clock), BL (back light LED) and MISO (or SDO).

As mentioned above, the ILI9341 TFT display controller works with 3.3V only (power supply and control lines). The display module is supplied with 5V that comes from the Arduino board. This module has a built-in 3.3V regulator which supplies the display controller with 3.3V from the 5V source.

To connect the Arduino to the display module, I used voltage divider for each line which means there are 5 voltage dividers. Each voltage divider consists of 2.2k and 3.3k resistors, this drops the 5V into 3V which is sufficient.

The first library is a driver for the ILI9341 TFT display which can be installed from Arduino IDE library manager (Sketch —> Include Library —> Manage Libraries …, in the search box write “ili9341” and choose the one from Adafruit).

The ILI9341 TFT display is connected to Arduino hardware SPI module pins (clock and data), the other pins which are: CS (chip select), RST (reset) and DC (data/command) are defined as shown below:

The following Arduino code is from Adafruit ILI9341 library (graphicstest.ino) with some modifications in order to work with the above circuit diagram.

2.2 spi tft display module 240x320 ili9341 free sample

The ILI9341 TFT module contains a display controller with the same name: ILI9341. It’s a color display that uses SPI interface protocol and requires 4 or 5 control pins, it’s low cost and easy to use.

The resolution of this TFT display is 240 x 320 which means it has 76800 pixels. This module works with 3.3V only and it doesn’t support 5V (not 5V tolerant).

The ILI9341 TFT display board which is shown in project circuit diagram has 14 pins, the first 9 pins are for the display and the other 5 pins are for the touch module.

So, the display part pins are numbered from 1 to 9 (from left to right): VCC (5V), GND (ground), CS (chip select), RST (reset), DC (or D/C: data/command), MOSI (or SDI), SCK (clock), BL (back light LED) and MISO (or SDO).

Pins D5 (GPIO14) and D7 (GPIO13) are hardware SPI module pins of the ESP8266EX microcontroller respectively for SCK (serial clock) and MOSI (master-out slave-in).

The first library is a driver for the ILI9341 TFT display which can be installed from Arduino IDE library manager (Sketch —> Include Library —> Manage Libraries …, in the search box write “ili9341” and choose the one from Adafruit).

The ILI9341 TFT display is connected to NodeMCU hardware SPI module pins (clock and data), the other pins which are: CS (chip select), RST (reset) and DC (data/command) are defined as shown below:

Full Arduino code:The following Arduino code is from Adafruit ILI9341 library (graphicstest.ino) with some modifications in order to work with the above circuit diagram.

2.2 spi tft display module 240x320 ili9341 free sample

ER-TFT022-1 is 240x320 dots 2.2" color tft lcd module display with ILI9341 controller,optional capacitive touch panel with controller FT6236U and resistive touch panel,superior display quality,super wide viewing angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO ARM and Raspberry PI.It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.It supports 8080 8-bit,9-bit,16-bit,18-bit parallel,3-wire,4-wire serial spi interface. FPC with zif connector is easily to assemble or remove.Lanscape mode is also available.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!".Here is the link for 2.2"TFT Shield with Libraries, Examples.Schematic Diagram for Arduino Due,Mega 2560 and Uno.For 8051 microcontroller user,we prepared the detailed tutorial such as interfacing, demo code and Development Kit at the bottom of this page.

2.2 spi tft display module 240x320 ili9341 free sample

To download. click the DOWNLOADS button in the top right corner, rename the uncompressed folder Adafruit_ILI9341. Check that the Adafruit_ILI9341 folder contains Adafruit_ILI9341.cpp and Adafruit_ILI9341.

Place the Adafruit_ILI9341 library folder your arduinosketchfolder/libraries/ folder. You may need to create the libraries subfolder if its your first library. Restart the IDE

2.2 spi tft display module 240x320 ili9341 free sample

ILI9341 is a 262144-color single-chip SOC driver for a TFT liquid crystal display with resolution of 240x320 dots (RGB), comprising a 720-channel source driver, a 320-channel gate driver, 172800 bytes GRAM for graphic display data of 240x320 dots (RGB), and power supply circuit.

ILI9341 supports parallel 8-/9-/16-/18-bit data bus MCU interface, 6-/16-/18-bit data bus RGB interface and 3-/4-line serial peripheral interface (SPI).

ILI9341 can operate with 1.65V ~ 3.3V I/O interface voltage and an incorporated voltage follower circuit to generate voltage levels for driving an LCD.

ILI9341 supports full color, 8-color display mode and sleep mode for precise power control by software and these features make the ILI9341 an ideal LCD driver for medium or small size portable products such as digital cellular phones, smart phone, MP3 and PMP where long battery life is a major concern.

2.2 spi tft display module 240x320 ili9341 free sample

I have some of this cheap, little Displays. They are working very well. To construct a case for them, i made this model with FreeCAD. The dimensions are not very accurate, because i used only some fotos with my digiscope software to get them. ...If you...

Display with SPI communication protocol, sold on Ebay. The dimensions are from datasheet and from a real pc board. The 2 connectors can be soldered if needed. ...Many details are not represented for simplicity.

Models from MSP2202 (2.2") and MSP3218 (3.2") TFT display modules (or similar), which might be handy for a placeholder in designs, for example enclosures. Please compare MSP2202 and MSP3218 datasheets with your displays to confirm that there are no...

2.4" TFT Display ILI9341 Box/Housing. There is place to add a power on/off switch in the lateral. Inside I have an Arduino Leonardo, a battery and one IEEE 802.15.4 module to receive data packets. ...Ready for SD hole.

ER-TFTM090-2 is 9 inch lcd module tft display w/optional touch panel screen,i2c+serial spi+parallel,microsd card slot,font/flash chip for arduio,8051,stm32.Souce from EastRising/buydisplay.com

ER-TFTM043A2-7R is 4.3"800x480 tft lcd display with RA8875 controller board, optional touch panel,serial/parallel interface,micro sd card slot,font,flash chip.Souce from EastRising/buydisplay.com

ER-TFTM1.54-1 is 1.54 inch IPS tft lcd display Module,240x240 resolution,built-in ST7789 controller,SPI interface with pin header for arduino,raspberry pi.Souce from EastRising/buydisplay.com

ER-TFTM043-3 is 4.3" tft lcd module display with serial,spi,i2c and parallel interface,RA8875 controller,microsd card slot,font ic,flash chip.Souce from EastRising/buydisplay.com

ER-TFTM080-2 is color 8"lcd module tft display w/optional touch screen,i2c+serial spi+parallel interface,microsd card slot,font/flash chip for arduio.8051,stm32.Souce from EastRising/buydisplay.com

ER-TFTM050-3 is 5 inch tft lcd module WVGA 800x480 display,serial,spi,i2c parallel interface,RA8875 controller,capacitive or resistive touch screen panel.Souce from EastRising/buydisplay.com

... and a 1.8 "SPI TFT. I installed the following LCD: http://www.ebay.de/itm/1-8-128X160-SPI-TFT-LCD-Display-Modul-SD-Card-fur-Arduino-AVR-/172477060959 The whole thing is for the following project: https://wiki.maschinendeck.org/wiki/Freifunk-Scanner

Case for the screen 2.8 inches 320x240 such as 240x320 2.8" SPI TFT LCD Touch Panel Serial Port Module With PBC ILI9341 2.8 Inch SPI Serial White LED Display with Touch Pen

A Lite CAD Model from 2,8" TFT Module with Touchscreen and SD-Card slot with ILI9341 Controler, mainly designed by own measured datas from a module. ...

This is a TFT display bezel that holds a "2.8 TFT SPI 240x320 V1.2" display on the front panel of a project panel. 4 machines screws hold the bezel on the panel with the display module trapped between the panel and the bezel. 4 clearance holds need...

7" TFT Display case designed to be used with Othermod Raspberry Pi LCD DPI Topper. I made this case with the intentions of gluing the face plate to a two-way mirror and running Todo lists and calendar appointments off of it. Pi and topper are...