3.5 tft lcd shield touch screen kit price

Spice up your Arduino project with a beautiful large touchscreen display shield with built in microSD card connection. This TFT display is big (3.5" diagonal) bright (6 white-LED backlight) and colorful (18-bit 262,000 different shades)! 320x480 pixels with individual pixel control. As a bonus, this display has a optional resistive touch panel with controller XPT2046 attached by default and a optional capacitive touch panel with controller FT6236 attached by default, so you can detect finger presses anywhere on the screen and doesn"t require pressing down on the screen with a stylus and has nice glossy glass cover.

The pin32 (SDO) of 3.5 display module is also used by touch panel or SD card SPI interface, so we must cut off this pin to avoid conflict with the touch panel or SD card.

The shield is fully assembled, tested and ready to go. No wiring, no soldering! Simply plug it in and load up our library - you"ll have it running in under 10 minutes! Works best with any classic Arduino (Due/Mega 2560).

This display shield has a controller built into it with RAM buffering, so that almost no work is done by the microcontroller. You can connect more sensors, buttons and LEDs.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!" - we"ve written a full open source graphics library at the bottom of this page that can draw pixels, lines, rectangles, circles and text. We also have a touch screen library that detects x,y and z (pressure) and example code to demonstrate all of it. The code is written for Arduino but can be easily ported to your favorite microcontroller!

The official ODROID Ubuntu image is required to configure the display shield. You can simply download the Kernel updates (via dist-upgrade) and configure your ODROID for this display shield.

GPU/VPU hardware acceleration requiring OpenGL-ES and video playback are not supported - To playback video on this screen, the file has to be transcoded to 480x320 with FFMPEG software decoding.

Are you looking for a 3.5" TFT Display to add to your product or project? We"ve got a handful of different TFTs with a 3 1/2 diagonal dimension. Most of them support 16-bit Parallel, 18-bit Parallel, 8-bit Parallel, 9-bit Parallel, RGB, and SPI. While all TFTs are transmissive, we carry some that are bright enought to be sunlight-readable. As you can see we offer a variety of pixel densities for this size, 480x640, 320x480 and 320x240. If you"re looking for a different 3.5 inch TFT display that isn"t listed here, please contact our support team, they"d love to help you find the perfect display for your requirements.

It is the cutest display for the Raspberry Pi. It features a 3.5" display with 480x320 16-bit color pixels and a resistive touch overlay. It"s designed to fit nicely not only to the Pi Model A or B but also works perfectly fine with the Model B+/2B/3B/4B.

The 3.5" TFT LCD Touch Display Shield for Arduino has been fully assembled, tested, and is ready to use. Install the touch display without any wiring or soldering! Simply plug it in and load a library; you"ll be up and running in less than 10 minutes! It works best with any traditional Arduino ATMEGA328 board. So add a beautiful touchscreen display shield with a built-in microSD card connection to your Arduino project. This TFT display is large (3.5′′ diagonal), bright (4 white LED backlights), and colorful (262,000 different shades)!

The TFT display has 480x320 pixels and individual pixel control. It has significantly higher resolution than a black and white 128x64 display. As an added bonus, this TFT display includes a resistive touchscreen, allowing you to detect finger presses anywhere on the screen.

The control and driving circuit of TFT displaymodules is low voltage and FRIDA micro-power CMOS circuit, can be easily damaged by static, static damage is an irreparable damage, and sometimes human have hundreds of volts of high voltage static electricity, therefore, in handling, assembling and use should be extremely careful to prevent static electricity:

Shield for Arduino Uno consisting of a TFT LCD display with 3.5" resistive touch screen, ILI9486 graphic controller, 480x320 pixel resolution, 65,000 colors, white LED backlight, SD card slot and SPI interface. Ideal for creating applications that need to display data, photos and videos. Suitable for interfacing with Arduino Uno, it is also compatible with Fishino, Nucleo, Xnucleo, MAKERUNO and UNO PLUS (see related products).

The TFT LCD Touch Screen Module for the Arduino is a version of a liquid crystal display(LCD) that uses thin film transistors(TFT) electronic that allows a user to create an interact-able interface between the user and the system. As the name may suggest, this screen module has the touch screen function.