kd58c lcd display pricelist

Product Name and Model 1Specifications 1Appearance and Size 1Display Layout 1Function Summary and Button Definition 2 Function Summary 2 Button Definition 2General Operation 2 Turning eBike On/Off 2 Turn Front Light On/Off 2 Display Interface 3 Pedal Assistance Level Selection 3 Power Indicator 4 Error Code Identification 4General Settings 4 Clear Trip 4 Unit Selection (MPH or Km/H) 5 Slow Start 5 *Specific Set Settings* 5 Pedal Assist Power Set 5 Speed Limit Settings 6 Set Password 7Recover Default Settings 7Error Code Definitions 7 Error Code 21 7 Error Code 22 7 Error Code 23 8 Error Code 24 8 Error Code 25 8 Error Code 30 9Appendix 9Tower KD58C Electric Bicycle Intelligent DisplaySpecifications ● 48V Power Supply ● Rated current: 10mA ● The maximum working current: 30mA ● Off leakage current: <1uA ● The supply controller working current: 50mA ● Working temperature: -20 ~ 60 ​℃ ● Storage temperature: -30 ~ 70 ​℃

Button Definition -​There are three buttons ( ​ , ,​ + ​) on the KD58C display that represent the followingfunctions: ​DOWN, POWER/MODE, UP​​.​

After turning on the eBike system, the display shows the speedometer in the main monitor.Press POWER to transition through the available six display interfaces:

Assistance levels indicate the output power of the motor. The default value is level 0, so as asafety precaution when you turn on your LCD display your eBike’s pedal assistance will not beengaged. .

The motor output power will be displayed on the display as below in an inverted triangle. Themore of the triangle that appears, the more battery you are currently consuming. When you arecompletely using your own pedal power or momentum, your power indicator will be minimal,which means you’re not draining your battery at all currently. This indicator varies from momentto moment to show you how reliant you are being on your battery reserves:

To exit the settings menu, hold the ​DOWN( - )​ ​button for two seconds.If there are not any operations for one minute, the display will exit the settings menuautomatically.

Clear Trip is used to reset the trip distance. Press the ​UP ​or ​DOWN ​button to choose YES orNO to clear the trip distance. The default value is NO. Press the ​POWER ​button to confirmthe selection, the display will then show OK and return to the general selection settingsinterface.

To change this setting, press ​UP​ ​or ​DOWN​ ​to increase or decrease until the desired speedlimit is displayed. Press ​POWER​ to store the selection and return to the general selectionsinterface.

Recover Default SettingsTo reset the LCD screen to the default factory settings, press both the UP and POWER buttonsfor 2 seconds. Select Y/N (yes/no). It may take 1 minute for this to register. Note that this actioncan not be undone. It will reset your password to the default setting of 1 2 3 4

● When the instant current exceeds double the rated current, or the continuous current exceeds the rated current, it may stop working and display this error. Since all controllers for Tower eBikes are 48V/20A controllers, this error means that the instant current is over 40A or the continuous current is over 20A.

Definition: There is a faulty connection running from the throttle sensors to the main controller.Throttle is not responding even after the battery is turned on, LCD is powered up, and thethrottle button is pushed in.

Definition: Connection error between the brakes and the bike itself. Brakes will still manuallywork, but not they are not in sync with the speedometer and LCD screen.

● Caused by the brakes being used while the LCD screen is being turned on. While powering up the LCD screen make sure the brakes are not touched and in their upright position.

Try turning on your LCD screen while not touching any brake lever. If the error code persists,inspect brake cables. Follow the cable wiring running down from one brake lever and unplug theconnection point. Turn on the LCD screen and test again. Run this test to figure out which brakelever (left or right) is causing this error code.

Follow the cable running from the LCD screen and ensure it is plugged in underneath the blackwiring frame. Ensure plugs underneath the controller, and by the foot pedals are plugged infirmly.

I have fitted Woosh DWG22C rear hub motor kits to two of my bikes and have been very pleased with the results. The kits use cadence sensing and speed control to modulate the output from the motor. The controller is made by Lishui and the LCD display is a King Meter 529.

1) I understand that some displays / controllers allow a degree of user customisation, but I’ve not seen any way to modify the parameters of the King Meter 529. Is this LCD display ‘locked’ or is there any software to permit minor modifications? I’m not interested in changing the fundamental elements such as maximum permitted amps, just the power level settings.

2) Another possibility is to replace the King Meter 529 with one of the ‘better’ King Meter displays such as their SW-U model as this can also display the watts currently used by the motor. Not an essential feature but a ‘nice to have’.

I’m not sure if this display would connect to the existing Julet connectors in the Woosh harness or even if it can be obtained easily in the UK, but might be worth investigating. I have assumed that this display would be able to communicate with the Lishui controller as it is the same manufacturer as the original display.