monoprice desk mount for 2 lcd displays pricelist

Mounted 2 Dell monitors. They were sell within the limit for weight.. The instructions could use some change. The end pieces must be taken off to insert the mounting plates into the arms. the mounting plates for ease of installation should be test fit to the monitors so to make sure you have the spacing correct to allow mounting the monitors onto the bracket once you"ve placed it into the arm channel. The Drawing in step 3 shows the bracket with the solid mounting plate located on top. For ease of mounting I placed the slotted part of the plate at the top. The Lock Collar mechanism is weak. It is easy to misalign the threads and the weight of two monitors allows it to slide down the pole. I found I needed to add painters tape around the pole in line with the locking collar to keep the arms at the height I wanted. Locking collar no matter how hard I tried would not engage its threads uniformly, they are just to wide apart to prevent binding as the collar twist out of alignment as you tighten it. Other than this it works great.

I purchased this mount to stack monitors for my Digital Color grading suite. After purchasing a 3rd monitor for critical color evaluation, I found there simply wasn"t enough lateral space to accommodate the new 27 inch monitor with my other 24 and 25 inch monitors; I had to go up to be able to use all three on my current desk.

I suggest you purchase a small tube of Loctite screw thread locker (or use some fingernail polish in a pinch), back out the main screws that hold the collars that hold the VESA mounts to the pole and lock these screws down TIGHT before attempting assembly or they might loosen up and allow the monitor to swivel horizontally after mounting the monitors.

Also, since the metal parts look as if they are powder coated, the screw holes on some mating surfaces might be a bit difficult to get started, so before you are trying to balance a monitor and start a screw into a mating hole, run these screws in and out of them to clear out any manufacturing over spray in the threaded holes. Makes life easier...

If you are doing this by yourself, as I did, I found the easiest way to mount the bottom monitor to the poles were to attache the VESA mounts to the monitor, stand the monitor on its side, resting on the desktop and then bolt the VESA mount to the collar. You only then have to pivot the monitor to horizontal and then tighten the collar around the stand pipe. The top monitor should be assembled to the VESA plate, attached to the collar, roughly leveled and then lowered over the pole to the correct height. It"s tricky but it can be done by one person.

Be prepared to spend some time adjusting and re-adjusting the height, tilt and level of each monitor to get them just right, as they lock in place and are not adjustable when fully tightened. Also, be aware that if one of your monitors has a connection you use that sticks out the back of the monitor at a 90 degree angle in line directly under the VESA mount, you will have trouble tilting the monitor down. My uppermost monitor had such a cable and it took some finessing to get it in place with the stiff video cable sticking out and hitting the support pole, but I was able to make it work.

My only concern now is that I might have a stiff neck from looking up at the top monitor for long periods, but considering my other options (basically none), I"ll have to learn how to deal with it...

If you do not like an article, you can return it to us within 30 days of delivery. Please contact us at eusupport@monoprice.com to receive a free return label. Please print the return label, stick it on the carefully sealed package and hand it over to your local post office. Please keep the document with the tracking number carefully.

Unboxing this monitor arm was remarkably easy, with all the pieces arriving together in one box. The monitor arm was one piece, the base was another, the mounting plate a third, and then the nuts and bolts to attach the base to the clamp. We were able to fully build this monitor arm in around five minutes, even while double-checking the directions to make sure we were building everything correctly.

We could tell out of the box that this arm is designed for a heavier monitor (Currently using a display that weighs just over 21 lbs), so we chose to attach it to the most heavily-used desk in our office space.

We wanted something that we knew would allow for easy monitor swapping – as we change out monitors pretty frequently in our line of work (so we were thrilled to see the quick-release VESA mount allowing for easy removal of the monitor from the arm) – while still looking clean and ergonomically correct. The base, at first glance, seemed rather large, with a substantial clamp - however, after attaching it to our desk, we understood the scale and no longer felt like it was oversized.

This model is a single-arm monitor mount, so only supports one monitor, and additionally has one swivel point, unlike some other models. This design breaks down to the ability to have an excellent range of motion for moving your monitor around; however, not as much as if you had a second arm and swivel point.

We had the opportunity to try this monitor arm out with a plethora of different products during our testing time. We also currently use it with a 34 inches ultrawide, but it has stood up just fine to monitors ranging from 27 inches to 40 inches, both with 16:9 aspect ratios.

There are several reasons why you might need a monitor mount. Perhaps you share your office with someone, and you need to be able to adjust the position of your screen so that it"s not in their line of sight. Or maybe you have neck or back problems, and you need to be able to adjust the height and angle of your monitor in order to reduce pain. Whatever your reason, a good monitor mount can make your life much easier.

Despite the cumbersome name, Monoprice"s desk mount is an excellent product for the modest price tag. While rated for large displays, it could handle smaller screens just as easily. Plus, it can handle ultrawide monitors, which shows that it can hold some heavy displays. When using those wider screens, the visible cables in the corner are not seen while sitting at the desk, making the one con about this monitor arm irrelevant. Therefore, depending on the screen, this could be a perfect choice.Monoprice Workstream Heavy-Duty Single-Monitor Full-Motion Adjustable Gas-Spring Desk Mount: Price Comparison

The Essential Quad Monitor Articulating Desk Mount is designed to mount a four 10" ~ 30" displays weighing up to 22 lbs. each above your desk. The elevated display position not only adds space to your desk, but also improves your posture by allowing you to look straight ahead instead of downward. It also creates a neat and clean professional appearance, which improves the look of any home or office environment. The mount can be swiveled 180°, tilted 90° upward or downward, and rotated 360° for quick and easy swapping between landscape and portrait orientations. The quick release lever on the back of the mount allows you to raise or lower the display at will, without the need for any tools.

Computer Monitor Mounts & Stands└ Monitors, Projectors & Accs└ Computers/Tablets & NetworkingAll CategoriesAntiquesArtBabyBooks & MagazinesBusiness & IndustrialCameras & PhotoCell Phones & AccessoriesClothing, Shoes & AccessoriesCoins & Paper MoneyCollectiblesComputers/Tablets & NetworkingConsumer ElectronicsCraftsDolls & BearsMovies & TVEntertainment MemorabiliaGift Cards & CouponsHealth & BeautyHome & GardenJewelry & WatchesMusicMusical Instruments & GearPet SuppliesPottery & GlassReal EstateSpecialty ServicesSporting GoodsSports Mem, Cards & Fan ShopStampsTickets & ExperiencesToys & HobbiesTravelVideo Games & ConsolesEverything Else

This website is using a security service to protect itself from online attacks. The action you just performed triggered the security solution. There are several actions that could trigger this block including submitting a certain word or phrase, a SQL command or malformed data.

Products with UPC 889028036266 were listed on the following websites. Product prices are accurate as of the date/time indicated and are subject to change.

• The HX features a post design, frees up space and allows positioning of your display for greater productivity.Sleek and streamlined, it accommodates large monitors weighing up to 42 lb - 19 kg