5 inch 800x480 hdmi lcd touch screen factory

1. Connect the TOUCH interface of LCD to the USB interface of PC. Wait for a while, the windows will automatically recognize the touch function.2. If you use HDMI, you need to connect the HDMI interface of LCD to the HDMI port of PC. About 10s later, you can see the LCD display properly. If you need the audio, you can insert a 3.5mm earphones to HP ports, or connect to the related speaker module through the speaker interface (such as 8 ohms 5-watt speaker).3. If you use VGA, you need to connect the VGA interface of LCD to PC"s VGA ports by Mini HDMI to VGA Cable. After about 10 seconds, you can see the LCD display normally.

A wide variety of 5 inch touch screen options are available to you, such as call center and on-line technical support, free spare parts and others.You can also choose from 16:9, 16:10 and 4:3 5 inch touch screen,As well as from 4g, gsm, and 3g. And whether 5 inch touch screen is new, stock, or {3}.

All the accessories listed below tier pricing need to pay.We won"t deliver until you select. Power adaptor should be 5V/2000mA in output and center pin for positive voltage and the outer shield for negative voltage .The temperature for controller RTD2660 would increase during working.That"s normal phenomenon,not quality problem.

ER-TFTV050A1-4 is 800x480 dots 5" color tft lcd module display with small HDMI signal driver board,optional 4-wire resistive touch panel with USB driver board and cable, optional capacitive touch panel with USB controller board and cable, optional remote control,superior display quality,super wide view angle.It can be used in any embedded systems,car,industrial device,security and hand-held equipment which requires display in high quality and colorful video. It"s also ideal for Raspberry PI by HDMI.

Winstar launched a 5" for HDMI signal Interface Mini Computer Display which item No. is WF50BTIFGDHTV. This 5 inch TFT Display with Resistive Touch Panel is a mini panel-mountable display, made of resolution WVGA 800x480 dots. This WF50BTIFGDHTV comes with a control board with a HDMI signal interface and a 40-pin connector on board; it is designed to make Raspberry Pi usage become easily. This display has a USB interface Resistive Touch screen overlay on TFT panel. The Capacitive Touch Panel also is available for option. We designed a connector part no. WWHDMI-00# for optional, the customers can use it to connect WF50BTIFGDHTV module with your Raspberry Pi directly. If the customers do not require a 40-pin header connector on board, please choose WF50BTIFGDHT0.

This display is small and compact, you can simply to use it to work with Raspberry Pi, and also you can use this Mini Computer display with any embedded system which has a HDMI signal output. The 5" display is 800x480 resolution, which is just enough to run most software, but still small enough that it can be used in portable or embedded projects without the bulk. Please note, this product does not include an HDMI or USB cable.

WF50BTIFGDHTV#: with a 40-pin header connector on board, supports up to Raspberry Pi 3B+ (contain Pi 4B) version. If customers choose Raspberry Pi 4 version, please note the interface is Micro HDMI; customers need to use the Micro HDMI to HDMI cable for these TFT series products.

RFF50VB-1IW-DHG is a 5-inch, resolution 800x480 pixels, TN transmissive color active matrix TFT LCD display, featuring HDMI signal with projected capacitive touchscreen (USB interface). This module has built-in controller TFP401, supporting HDMI connector (only DVI signal) interface. The PCAP touchscreen has a built-in IC ILI2130 which enables 1-point/2-point/multiple-point touch.

★RFF50VB-1IW-DHG: with a 40-pin header connector on board, supports up to Raspberry Pi 3B+ (contain Pi 4B) version. If customers choose displays supporting Raspberry Pi 4, please note that the interface is only compatible with micro HDMI. Customers need to use “Micro HDMI to HDMI” cable for these TFT series.

When using the 800X480 5inch HDMI LCD for the first time with the Raspberry Pi the display does not cover the entire 5 inch display. This tutorial will show you how to get rid of the black border on the display .

FAQWhy the LCD doesn"t work with my Raspbian?To use the LCD with the Raspberry Pi official image, driver (SPI touch interface only) should be installed first. Please refer to the user manual.

However, for the first testing, you may want to use our image directly (if provided).Why the LCD still doesn"t work with the Waveshare provided image?Make sure the hardware connection is correct and connects fine.

The PWR will keep on and the ACT will keep blinking when the Raspberry Pi starts up successfully, in case both of the two LEDs keep on, it is possible that the image was burnt incorrectly OR the TF card was in bad contact.Which power supply should I use?It is recommended to use a 5V/3A power adapter for the Raspberry Pi other than USB connection, otherwise the Pi may failed to start up because the PC"s USB port might have not enough power.

This is a Waveshare 5-inch Capacitive Touch Screen LCD, with a resolution of 800×480 and a capacitive touch panel, which supports Raspberry Pi and can also be used as a computer monitor. This product supports Windows 10/8.1/8/7 OS. For the Windows 10/8.1/8 OS, the touch screen supports multi-touch up to 5 points. For some Windows 7 OS, the touch screen supports single touch only. This LCD can support Raspbian / Ubuntu / Kali / Retropie and WIN10 IoT systems. When the LCD works on systems such as Raspberry Pi, the resolution must be set manually, otherwise, it will cause abnormal display. There is no such problem when the LCD works on the PC version of Windows.

Compatible and Direct-connect with any revision of Raspberry Pi. (If you are using a Raspberry Pi Zero / Zero 2 W, an additional HDMI cable is required).

Raspberry Pi leads out 40 GPIO pins, while the screen leads out 26 pins. When connecting, pay attention to the corresponding pins and Raspberry Pi pins.

5) Insert the TF card into the Raspberry Pi, power on the Raspberry Pi, and wait for more than 10 seconds to display normally. But the touch is abnormal at that time, and the touch needs to be calibrated as the following steps.

3. After reboot, touch will work normally under normal circumstances. But for different resistance screens, the accuracy of using the default calibration parameters may not be very suitable.

You can perform touch calibration by clicking the Raspberry Pi icon on the taskbar, selecting Preferences -> Calibrate Touchscreen, and following the displayed prompts.

4. After calibration, the following data will be displayed. If you want to save these touch values, you can replace the data in the red circle with the data in the corresponding position in 99-calibration.conf.

The installation of xserver-xorg-input-evdev and xinput-calibrator in Ubuntu system reports an error, so the touch cannot be used normally. How to solve it?

The installation of xserver-xorg-input-evdev and xinput-calibrator in Kali system reports an error, so the touch cannot be used normally. How to solve it?