1.8 tft display module spi 128x160 for sale

ER-TFT018-2 is 128x160 dots 1.8" color tft lcd module display with ILI9163C controller ,optional 4-wire resistive touch panel,superior display quality,super wide viewing angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO ARM and Raspberry PI.It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.It supports 8080 8-bit,9-bit,16-bit,18-bit parallel,3-wire,4-wire serial spi interface. FPC with zif connector is easily to assemble or remove.Lanscape mode is also available.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!".Here is the link for 1.8"TFT Touch Shield with Libraries, EXxamples.Schematic Diagram for Arduino Due,Mega 2560 and Uno . For 8051 microcontroller user,we prepared the detailed tutorial such as interfacing, demo code and Development Kit at the bottom of this page.

This lovely little display breakout is the best way to add a small, colourful and bright display to any project.Since the 1.8 Inch TFT LCD Module display uses 4-wire SPI to communicate and has its own pixel-addressable frame buffer, it can be used with every kind of microcontroller. Even a very small one with low memory and few pins available!

The 1.8 display has 128160 colour pixels. Unlike the low cost Nokia 6110 and similar LCD displays, which are CSTN type and thus have poor colour and slow refresh, this display is a true TFT! The TFT driver (ST7735R) can display full 18-bit colour (262,144 shades!).

The breakout has the TFT display soldered on (it uses a delicate flex-circuit connector) as well as an ultra-low-dropout 3.3V regulator and a 3/5V level shifter so you can use it with 3.3V or 5V power and logic.

Features :1.8-inch serial SPI colour display moduleSupport analogue SPI and hardware SPIThe LCD has a wide viewing angle, the contrast is also very suitable.Good quality display.

Since the 1.8 Inch TFT LCD Module display uses 4-wire SPI to communicate and has its own pixel-addressable frame buffer, it can be used with every kind of microcontroller. Even a very small one with low memory and few pins available!

The 1.8 display has 128160 colour pixels. Unlike the low cost Nokia 6110 and similar LCD displays, which are CSTN type and thus have poor colour and slow refresh, this display is a true TFT! The TFT driver (ST7735R) can display full 18-bit colour (262,144 shades!).

The breakout has the TFT display soldered on (it uses a delicate flex-circuit connector) as well as an ultra-low-dropout 3.3V regulator and a 3/5V level shifter so you can use it with 3.3V or 5V power and logic.

Key words: tft 1.8", 1.8 tft lcd, 1.8" tft lcd, 1.8 inch tft lcd, tft lcd 1.8, 1.8 tft display, 1.8" tft display, 1.8 inch tft display, tft display 1.8, tft display 1.8", 1.8 tft lcd, tft 1.8

This ST7735S 1.8" TFT Display features a resolution of 128×160 and SPI (4-wire) communication. Integrated with a microSD card slot, it allows you to easily read full-colour bitmaps from the SD card.

The module provides you with two wiring methods: pin header and GDI (General Display interface). You can directly connect the display to a FireBeetle main controller using the included FPC cable. Plug n" play and easy to wire, the display supports a low refresh rate and offers a good display effect and strong versatility.

This small screen is one of the best ways to add a small, colorful and bright screen to any project. 1.8 Inch TFT LCD Module can be used with any microcontroller since it uses 4-wire SPI for communication and has its own pixel addressable frame buffer. It can even be used with low memory and few pins! The TFT driver (ST7735R) can display full 18-bit color (262,144 tones). The 1.8 Inch SPI 128×160 TFT LCD Display Module always comes with the same driver chip, so you don"t have to worry about your code not working from one to the other. Also in a small space, a microSD card holder is built in, so you can easily load full color bitmaps from a FAT16/FAT32 formatted microSD card.

I got a few random displays of several types and it was, um, challenging to get them working. Now each has a minimum test program associated with it I can use as a starting point.

I have found the really cheap displays to function, but seem clearly to be factory seconds, like the OLED I had that aged out waaay too soon. And the touch screen that needed more than a touch alla time.