kuman uno r3 3.5 tft display screen brands

The touchscreen came on time and looks to be in mint condition. My project is to make a Kuman 3.5 TFT lcd marry a Keystudio Mega 2560. I"m about three hours into my weekend now and I"m clearly missing something quite obvious when it comes to lights and action. When I plug the Mega into the hard drive computer port it lights up and when I check the device manager I can see the the Mega is listed in ports com. If I plug the Kuman touchscreen into the Mega the lights go off on the Mega board and the device manager resets to not show the Mega. The Kuman TFT comes with a small cd with libraries and so forth. When I upload the test library it works okay (within the IDE sketch) when I verify, but when I go to upload to the actual board I get this error message. I have searched the Arduino IDE site for these particular devices. I have found several Kuman videos on you tube but for a different style that has only one row of pins on the side. I"ve uploaded every library I can think of or have heard suggested. I suspect this is a simple problem but I may be more simple. I am open to any primary or basic suggestions if you can spare the time. This is the model I"m using. I also have a spare legit Uno lying around and I get the same results. Do I have the pins lined up wrong? They are actually pressed into place, in the photos I just wanted to show you the positions. What am I doing wrong please? Update...well it works if I follow the pin diagrams with leads, add power and change one letter in the code. So I powered it up, I assume the rest of the test programs will follow. * update - turns out the first two pins on the mega are not to be used and then everything lines up and works. I have a slow learning curve.

I bought online this LCD Touchscreen Kuman SC3A-NEW-UK. It uses ILI9486 drivers, but it didn"t include any instructions manual, and kumantech.com seems to be devoid of complete technical documentation about SC3A-NEW-UK model.

Just in case it wasn"t noticable: I am trying to make a "Hello World" for my SC3A-NEW-UK"s LCD Touchscreen from an Arduino UNO board. In other words: just print "Hello World" to see if it works.

This compiled in Arduino IDE, no problem, but I still don"t know if it will work well with my screen. I am also confused about initialization of the TFT object and how would I have to wire the LCD screen to the Arduino depending on this initialization:

...i mean, my LCD screen has CS and RESET pins, but what is DC supposed to be here? (in this context, I don"t think it stands for "Direct Current"... but there"s no DC pin reference in my LCD screen written "AS IS"... ?? This brings me more confusion...

...specially having in mind that I don"t know how am I supposed to wire the LCD screen to the Arduino yet. It seems the LCD pins have been designed to fit in directly to the Arduino board without thinking too much about it (like the shape is the same), but that would make the screen getting all the Arduino UNO"s pins for itself, so I don"t think so...

...so, powering the screen shouldn"t be a big deal, but, how am I supposed to connect everything else? I am completely misguided about how am I supposed to interact with the screen from Arduino code... what is RS pin for? Should I use 4-bit or 8-bit mode? (I think 4-bit would imply connecting 4 digital pins for the screen, and 8-bit the whole 8 pins from screen to the Arduino UNO board)? Should I use LCD_RD and LCD_WR? Well you have a picture of my confusion.

Even though I know how to control Input/Output in Arduino code to interact with analog/digital input and output pins at will with C++ in Arduino code (but even so, I think I"m still an Arduino n00b), this LCD screen"s physical interface is very confusing to me...

PD: I have read somewhere that this SC3A-NEW-UK Touchscreen is made to shield Arduino MEGA boards (by fitting the PINs directly into it), but mine is an Arduino UNO Board! (perhaps I shouldn"t have bought This LCD model, then?)... but I have sets of wires, pinboards and stuff... I don"t want to give up the idea of harnessing this LCD screen using an Arduino UNO. I don"t care about shielding feature, I just want to wire it and make it work. I will figure out how to shield electronics later on.

Based on VE7JRO"s answer, I managed to map the connections by seeing where the connections would go if I just fit the connections shielding the Arduino UNO, the way VE7JRO suggested:

I put NONE for A5 input, because that pin of LCD screen doesn"t have any name on it. There are another ones without name as well, that I didn"t include in this table. I believe (perhaps I"m wrong believing it, I don"t know) that those pins without name have no use.

The bad thing about this layout is that it consumes almost all the Arduino pins, so I would not be able to attach additional circuits. However, perhaps I should not be worrying about earning connections yet, before testing the screen.

I still don"t know much of the details about what pins do what for the screen, but I have read somewhere that LCD_D0 to LCD_D7 are meant to receive digital data in some kind of 8-bit parallel mode. But I also heard that there is a 4-bit mode. If I could use that mode with this screen, I would be able to have 4 free digital pins for anything else...

I tested VE7JRO"s code. LCD Screen did draw the interface as expected. But buttons didn"t respond. I found out the code sample needs further calibration.

...because their values when I touch the screen with the touchpen are very weird. I tried to guess which ranges they go, and they don"t make sense when I move around the screen. Perhaps it"s because this strange "Z instead of Y" mapping from the TSPoint object. Perhaps pixel_x and pixel_y don"t need to make an intuitive sense, perhaps it"s just some intrincated in-bound logic that only makes sense within electronics" low-level scope, or within Adafruit_GFX_Button.press method, I don"t know... but x, y and z readings from TSPoint object seem very accurate, despite Y being Z and Z being Y...

There are 22 test sketches that come with the MCUFRIEND_kbv library. One of them scans your display and outputs configuration information (sorry, it"s been a while since I tested my screen). Another sketch will draw little boxes in each corner and sides. This is used to get the x y coordinates of the edges of your particular screen (it might be called TouchScreen_Calibr_native.ino).

z seems indeed sensitive to touch pressure, but it"s like its sensitivity is different depending on the touchpen"s position on screen (altough I"m not a robot, I think I was using more or less the same amount of force with my hand). It prints 0 when i do not touch the screen.

The fifth parameter is supposed to be the resistance measured between LCD_D6 and LCD_RS with the screen unplugged. Unfortunately, my multimeter can"t measure it for some reason (I put it in 2000 Ohms mode for reading resistance: I always get "1", the same than when I don"t connect anything... like if multimeter"s contacts aren"t working well, I don"t know)... so I left the default 300 value.

Frequently Asked Questions About Kuman Arduino UNO R3 3.5 inch TFT Touch Screen with SD Card Socket w/ Tutorials in CD for Arduino Mega2560 Board SC3A-1 in Bahamas

Where can I buy Kuman Arduino UNO R3 3.5 inch TFT Touch Screen with SD Card Socket w/ Tutorials in CD for Arduino Mega2560 Board SC3A-1 online at the best price in the Bahamas?

desertcart is the best online shopping platform where you can buy Kuman Arduino UNO R3 3.5 inch TFT Touch Screen with SD Card Socket w/ Tutorials in CD for Arduino Mega2560 Board SC3A-1 from renowned brand(s). desertcart delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.

Is Kuman Arduino UNO R3 3.5 inch TFT Touch Screen with SD Card Socket w/ Tutorials in CD for Arduino Mega2560 Board SC3A-1 available and ready for delivery in Bahamas?

desertcart ships the Kuman Arduino UNO R3 3.5 inch TFT Touch Screen with SD Card Socket w/ Tutorials in CD for Arduino Mega2560 Board SC3A-1 to and more cities in Bahamas. Get unlimited free shipping in 164+ countries with desertcart Plus membership. We can deliver the Kuman Arduino UNO R3 3.5 inch TFT Touch Screen with SD Card Socket w/ Tutorials in CD for Arduino Mega2560 Board SC3A-1 speedily without the hassle of shipping, customs or duties.

Is it safe to buy Kuman Arduino UNO R3 3.5 inch TFT Touch Screen with SD Card Socket w/ Tutorials in CD for Arduino Mega2560 Board SC3A-1 on desertcart?

Yes, it is absolutely safe to buy Kuman Arduino UNO R3 3.5 inch TFT Touch Screen with SD Card Socket w/ Tutorials in CD for Arduino Mega2560 Board SC3A-1 from desertcart, which is a 100% legitimate site operating in 164 countries. Since 2014, desertcart has been delivering a wide range of products to customers and fulfilling their desires. You will find several positive reviews by desertcart customers on portals like Trustpilot, etc. The website uses an HTTPS system to safeguard all customers and protect financial details and transactions done online. The company uses the latest upgraded technologies and software systems to ensure a fair and safe shopping experience for all customers. Your details are highly secure and guarded by the company using encryption and other latest softwares and technologies.

Features: This TFT LCD Screen Module with a LCD break , SD card and Flash design. So it"s a powerful extension module for your project. Dimension: 3.5 inch Controller: ILI9481 or ILI9488 driver(default in random) Resolution: 480x320 Data bits: 8 - 16 Interface pin number: 37 pin Distance: 1 mm Note: There is a film on the LCD, if there is scratch on the film when you receive the item, pls try to remove the film with your finger nail from the corner of the LCD, thanks. Package include: 1* 3.5 inch TFT touch screen 1* touch pen 1* CD with tutorial

We still recommend the Nextion K035 Enhancedas the best for most users, due not only to its reliable LCD panel, but also the hardware inside, which is superior to most other models. The Kuman SC3A-1, on the other hand, is less full-featured but also costs notably less. The Adafruit 1947is one with a bit of a reputation as a high-performing, lost-lasting touch screen, and the Walfront 7-Inchis one of the better large-format options around.

Arduino is an immensely interesting platform, and is a great way to create custom electronic controllers for a huge range of purposes. It"s also an excellent way for young people and other beginner engineers to get into the field. Because it"s so small and simple, low prices are somewhat of a hallmark of the category. The Nextion Enhanced models are packed with the most advanced features, and for full functionality, they"re the way to go, though they aren"t always the cheapest. Nonetheless, the 2.8- and 3.2- inch versions are great selections. For basic and more low-budget purposes, check out the Kuman, Elegoo, and HiLetGo, which are all designed to plug directly into the smallest Arduino boards. For more in-depth projects, it"s hard to beat AdaFruit and WishIOT, who offer a number of versatile and highly reliable options. And if you"re going for maximum visibility, check out the Walfront, which has a crisp and large screen, although be aware that most controllers won"t be able to achieve extremely high refresh rates at such high resolutions. Also keep in mind that there is a wide selection of projects, tutorials, and libraries for the entire Arduino family available online.