raspberry pi b+ lcd touch screen quotation

- Case is a clear plastic. The kind that looks as if it will crack or shatter if dropped. It is not thick nor feels durable, but the board snaps into place and the top snaps with the bottom half in a solid manner.

- The wifi adapter worked out of the box and was able to stream 720p from an internet streaming site (and 1080p from a local network drive). My wireless router was in the same room about 4 feet away. Don"t know how well the wifi works if placed in another room.

- For those that think the SD card is not 4GB - it is. There is almost invisible print on the generic SD card that when looked at under bright light and maybe a magnifying glass has perhaps a serial number with the last few characters saying 4G or 4GB.

Also, the card is partitioned, so Windows will only see the first 1GB partition. With the SD card in your computer, go to Control Panel > Administrative Tools > Computer Management > Disk Management, you will find the SD card and all of its partitions adding up to around 3.75GB if your kit shipped with a 4GB card.

Putting it together was literally a snap. Installing your preferred OS may be an issue. The pre-installed software on the SD card is NOOBS. It will bring up a menu of different operating systems to choose. Choose the one you want, and it gets installed in a usable form on the same SD card. Upon completion, the system reboots into the OS or XBMC setup you chose.

After snapping the board, case, usb adapters for wifi and wireless keyboard, plugging in hdmi and power, nothing happened. A red light on the board lit up, but nothing else. I went online and after some googling, I found out that if no OS is recognized, nothing will display on your TV/monitor. I unplugged the power, took out the SD card and re-inserted, and the system booted into NOOBS.

I chose to install RaspBMC. The install went fine, the system rebooted to an XBMC screen that had a slight pink glow over the entire screen. More googling, and realized the board may not be outputting enough power through the HDMI port. There is info online for configuring a config file so more power goes to HDMI. I couldn"t get to this file from the SD card plugged into my laptop because Noobs makes this partition not viewable under Windows.

Anyway, I setup my wifi SSID and password in RaspBMC and the system automatically started updating itself. After completion and a reboot, RaspBMC died. It could not finish a successful reboot and mount its partition. It was unusable!!!

Shut it all down. Googled how to remove all partitions on an SD card from Windows command prompt with the diskpart function and formatted the SD card to one big FAT32 4GB partition. Went to the OpenELEC website and downloaded and installed the OpenELEC image for the Raspberry Pi. Booted into the XBMC version of OpenElec, configured wifi and other settings. Tested by watching both 1080p and 720p content streaming from a local network drive and from over the internet.

The official Raspberry Pi 7” Touchscreen allows you to add touch inputs to your programs, creating a new way to interact with your projects. It also makes for a fantastic desktop screen for day-to-day use of your Raspberry Pi. Wrap it in one of our screen cases and take it anywhere – events, Raspberry Jams or even just your friends house for a coding evening!

For smaller projects, LCD and ePaper displays are a fun way to add a visual element to your projects. With simple code and wiring, they’re great for projects that require text, menus and navigation.

Raspberry Pi OS provides touchscreen drivers with support for ten-finger touch and an on-screen keyboard, giving you full functionality without the need to connect a keyboard or mouse.

The 800 x 480 display connects to Raspberry Pi via an adapter board that handles power and signal conversion. Only two connections to your Raspberry Pi are required: power from the GPIO port, and a ribbon cable that connects to the DSI port on all Raspberry Pi computers except for the Raspberry Pi Zero line.

I"m using it to run a lighting and irrigation system for my house. The color graphical interface allows me to use BMP images of my house and yard for control screens, and its built into an enclosure set into the wall for a slick professional look. I even put an access from the backside of the wall for wiring it without having to remove the Pi or the touchscreen.

Great responsiveness, inexpensive, can"t beat 10-finger multi touch! The python demos are really neat, too. Only gripe is that the screen isn"t oleophobic, but for the price I"ll take it!

This was easy to install and it looks good. The Touchscreen is responsive and clear, but you might want to use a stylus. The only issue i had is finding a case for it. You"ll want to get one right away, unless you have a 3D printer to make one yourself. The screen is really thin, so I didn"t want to carry it around without some protection. Overall, it"s a great touchscreen, especially for the price, and I like that it is Raspi-branded.

I purchased 5 touchscreen. Two before and three in January. Touch and display quality is superb. After two-three month of use (no rough use; handled with care), display LCD and front touchpanel (black bezel) break apart. They both are connected using a thin double sided tape. I was planning to use in industrial environment but after such issue, I dropped my plan to use it in industrial environment.

Five of two displays are not in good condition. First display"s touch-panel and display LCD was break apart after two-three month. The second among five displays had another issue. Display LCD was mounted slightly right side of the touchpanel. Once you power-up display, it is easily be seen that LCD panel was a bit off-side. The other display"s screen guard having so many scratches on them which seems mishandling.

I got a couple of these for several RPi projects that Im developing and they are working amazingly well for the application. If these fit your application needs I wouldn"t hesitate to recommend them.

This screen worked right out of the box! Touch worked great with my new pi 3! However aside how fragile the (non functional) edges are, the only real issue I see is upon shutdown of the pi... The screen goes through a series of screen washes/whiteouts and never really shuts off.. I have to pull power to get it to turn off.. I"ve even tried usb/provided jumper wires.. And both results in the same thing. Not sure if this an issue per se, but it is bothersome.. I can just turn the unit off, I need to unplug it too..

I am using Raspberry Pi 3. The display came up with no problems. I am just waiting for the Smarti Pi Touch enclosure (pre-ordered after the Kickstarter project closed) before continuing to work with it.

Basically, it "does what it says on the tin". It"s bright, relatively responsive and has acceptable color. Haven"t played much with the touch screen part of it yet, but very pleased so far!

The only question(s) that I have are regarding what sort of additional processor power is inside the screen, and whether powering it from the micro-usb connection whilst also bridged from the RPi3 is an issue (it hasn"t hurt anything, yet!).

No convenient mounting points - like a screw hole in each corner, or similar. I still haven"t figured out a good way to mount it in a non-standard box.

I WAS DISAPOINTED THAT THE UNIT DISPLAYS EVERYTHING UPSIDE DOWN. I HAD TO USE THE LCD_ROTATE=2 COMMAND IN CONFIG.TXT TO FIX IT. THE INITIAL BOOT IS STILL UPSIDE DOWN BUT I GUESS AFTER IT READ THE CONFIG.TXT, IT FLIPS. SHOULDN"T IT COME STANDARD RIGHT SIDE UP?

Hmmm, it should, and this isn"t an issue we"ve seen before. I would suggest getting in touch with our Tech Support team, they should be able to help you out.

Works like great. I also bought the case Which I love except you can not get to the SD card once it build. I use a small wireless keyboard so it nice combo. I Can Throw it in my back pack when I go to work too. This allow me more time to play with it.

With so many, phone and tablets that have hi res screens, this is disappointing. It does what it"s supposed to, but has a retro look. Non techy relatives are not impressed.

The must annoying feature is the bright white screen when it loses signal as the OS shuts down. The touch input is inconsistent as input. I was using the I2C for a device was not able to get it going on the alternate I2C, but fortunately the required clock and data are on the DSI cable ... wasted hours finding that out. An OLED display, higher res, and lower current draw would be really nice in the next version.

I forgot to check that this LCD touchscreen don"t have a case. Much better that you have a notification (e.g. recommending the user to purchase also a case) when purchasing this kind of product. But thank you for this product, I will purchase again soon.

The only minor drawback that everyone should be aware (which is to be expected, honestly) is that the display draws quite a noticeable amount of current. The SmartiPi case comes with an splitter USB cable for the power source, but if you expect to use that, be prepared with a (very) beefy power supply, else you"ll get the thunder icon on the screen all the time and a very reduced performance (Just discovered that the RPi3 reduces its own clock when power is low).

I currently power this with a separate 1.5Amp supply for the screen and a 2Amp supply for the RPi3 and everything works just nice. This totals to a whopping 3.5A, which may be overkill, but keep that in mind as a reference.

I am impressed with this screen, I also got the mating case (SmartPi Touch) and it assembled nicely. With the separate case, the included jumpers and cable are not needed. The PCB was already attached with the standoffs. The packaging was super! The screen is slightly larger than 7 inches. I measured it as 7 5/8" wide X 4 3/8 high with a diagonal measurement of 8 9/16.

Works very well, but I haven"t found reliable instructions. Internet search turns up lots of hits, mostly unreliable. Doesn"t work with the OSMC I have, and I haven"t had time to track down the problem. Didn"t find anything in the official blogs.

This official Raspberry Pi 7" touchscreens now come with the display controller already connected and mounted to the back of the display. You still need to be careful pulling forward the small black tab ends that connect a ribbon cable to the RPi.

I bought the companion enclosure as well. This Touchscreen works exactly as described. I am very pleased with the display. I ended up using a mouse anyway as the icons (while clear are very tiny) and selection areas are a bit small for fat fingers.

I connected it to a Raspberry Pi 3 B running Stretch and it seems to be working perfectly. I had been previously driving a VGA monitor from HDMI through an adapter. The RPI 7" screen started up just fine without changing or installing anything with the OS.

I connected it to a Raspberry Pi 3 B running Stretch and it seems to be working perfectly. I had been previously driving a VGA monitor from HDMI through an adapter. The RPI 7" screen started up just fine without changing or installing anything with the OS.

Based on other comments here and looking at one of these at a maker space, I bought the smartipi touch case for this; it"s strongly constructed and works great. Only issue was that I"m using this with a model 3 B+, and that takes a different door on the back than comes with the case (this is being fixed by the smartipi folks, but I don"t know the logistics of getting their new cases into Sparkfun)

It gets rid of a full sized monitor, which is great.. I gave a full system to my grandson for Christmas. After we put it together, his first question was, can I use it for home work?. All I need for it now is a Ups type battery charger for 5volts. It,s now sitting proudly on my aircraft instrument panel.

I have tried other touch screens for the Raspberry Pi. They had complicated assembly and were very difficult to get them to work. This unit was easy to install and get working, is very nice looking. I am very Happy with it.

Right out of the box it worked. Didn"t even have to do anything to the RPi (in fact, both were taken out of the box at the same time, connected, and worked on the first power up). Screen quality is good for price. Also ordered the "SmartPi Touch" case which holds everything together very nicely.

Ordered it, a Raspberry Pi 3 B+, and a power supply. (Had a mouse, keyboard, and uSD on hand.). It came a couple of days ago, and I put together yesterday. Had noticed in the documentation that there"s a micro USB power input, and a standard USB output. In the configuration where the power supply is plugged directly into the Pi and the LCD interface is powered via a USB cable plugged into one of the Pi"s USB ports to the LCD"s micro USB, the LCD won"t light up at all. When the power supply is plugged into the LCD controller board and the USB cable connects power to the Pi, I get "low voltage" warnings (yellow "lightning bold"). When I use the provided F/F jumpers, it works fine, but this will cause problems plugging in other "hats", as well as clearance problems. (In my application, separate power supplies would be a BIG PROBLEM.) BTW, I checked with two different USB cables, and got the same problems as well as when I tried an Adafruit 5.25V power supply. (I was about to try a second RPi3B+ when the original one stopped booting. Fortunately I had another that I"d been using as a "pass-around" sample at talks, and fortunately when I tried it, it still worked, so now the "dead" one will be passed around!) Also, it could prove really useful to know what size those mounting screws are in case they get lost! Ace Hardware recently opened a new store about half a mile from my house!

The screen is portable enough to take with you and the Pi will use it with no configuration change when it"s powered up. Used it to set up several Raspberry Pis in a remote lab. Touch screen is nice but bring along a keyboard if you have to do any setup work. One thing to make it better, replace the jumper wires with a ribbon cable connected to 1x5 and 2x2 pin headers.

I have a Raspberry Pi in each room of my home and they run a Kiosk interface for home automation, cameras and more. I"ve tried some cheaper ones and none have survived. (I"m hard on equipment) I haven"t managed to break one of these yet.

Got a PI3+, 7" touchscreen and SmartPI case for manufacture test. I put these together and booted the latest Raspbian. The LCD and touchscreen connect to the display connector using a short FPC cable. The display booted and the touch screen just worked out of the box. There were some nice but not well documented improvements. They provide a Y USB cable to power both the PI and the LCD. This is a cleaner solution than the jumper wires they provide.I"m not a big fan of using lego blocks in a industrial environment but the case went together easily and does a decent job of protecting the display and the PI. Some reported a inverted display issue but that seems to have been resolved.

A truly plug-and-play display for the Raspberry Pi. Does not steal any additional extension connector pins if you power it with a USB power supply and leaves the I2C1 interface available for other devices.

Big enough for somewhat squinting actual Raspberry PI development and computer work, but really shines for touch screen optimized large button control panels.

You can just install a Pi3 or 4 on the back, but with a 4 you really need some additional airflow. The SmartiPi Touch 2 enclosure works better. https://www.sparkfun.com/products/16302

It works fine, no glitches, no problems, no hair pulling moments. Once electrically connected to my RPi 3B+ it"s good to go. I run it with the "lite" version of the Raspberry Pi OS with only xorg drivers installed, no full desktop or windows manager, as part of an in-the-field project with a HQ camera attached. My only complaint is the ribbon cable could stand to be about 6 inches longer.

It works great, the colors are beautiful, and finger touch works fine. What I like most is that the Raspberry Pi GPIO pins are all still available - except for one +5v pin and one Ground pin. Both are redundant (i.e. others are available). So, this is not an issue at all. I also like that data connects to the Pi via the IPS ribbon cable. Another thing I like is that power connects to the Pi via two jumper wires. The Pi is fussy about its power supply voltage. So, the jumper wires are better because they are heavier gouge than a small PCB trace.

I connect a Pi v4 and put the whole thing in the SmartPI Touch 2 case from Sparkfun and now it looks pretty professional. Make sure you use a good power supply.

Where is the documentation? This thing is so poorly documented it"s almost a joke. The whole point of the RPi ecosystem is to enable Makers and learning about electronics, so why isn"t this fully documented?

I used this to build a portable utility/testing device for my company. It works fantastic with the SmartiPi Touch Pro Case on Amazon. The touchscreen functions great, only thing is you can"t register mousedown and mouseup events in Chromium (only click). Other than that it"s great!

I got it working the first try, easy to follow instructions. Trying to learn Kivy with Python for touch screen programming, That"s a lot more difficult.

It"s bright, clear, good color rendition. Touch input is responsive and accurate. Trivial to assemble and get going. Like the multiple power options. Would buy again.

The only drawback is that I wish there was a case I could purchase for it. I have seen 3D files for printing your own, but I do not have a 3D printer (yet).

By continuing to use AliExpress you accept our use of cookies (view more on our Privacy Policy). You can adjust your Cookie Preferences at the bottom of this page.

PO Box, APO/FPO, Afghanistan, Alaska/Hawaii, Albania, Angola, Anguilla, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Azerbaijan Republic, Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belize, Benin, Bermuda, Bhutan, Bolivia, Botswana, British Virgin Islands, Brunei Darussalam, Burkina Faso, Burundi, Cambodia, Cameroon, Cape Verde Islands, Cayman Islands, Central African Republic, Chad, China, Colombia, Comoros, Congo, Democratic Republic of the, Congo, Republic of the, Costa Rica, Côte d"Ivoire (Ivory Coast), Djibouti, Dominica, Dominican Republic, Ecuador, Egypt, El Salvador, Equatorial Guinea, Eritrea, Ethiopia, Falkland Islands (Islas Malvinas), French Guiana, Gabon Republic, Gambia, Georgia, Ghana, Greenland, Grenada, Guadeloupe, Guatemala, Guernsey, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras, India, Indonesia, Iraq, Jamaica, Jersey, Jordan, Kazakhstan, Kenya, Kuwait, Kyrgyzstan, Laos, Lebanon, Lesotho, Liberia, Libya, Macau, Madagascar, Malawi, Maldives, Mali, Martinique, Mauritania, Mauritius, Mayotte, Mexico, Mongolia, Montserrat, Morocco, Mozambique, Namibia, Nepal, Netherlands Antilles, New Zealand, Nicaragua, Niger, Nigeria, Oman, Pakistan, Panama, Papua New Guinea, Paraguay, Peru, Qatar, Reunion, Russian Federation, Rwanda, Saint Helena, Saint Kitts-Nevis, Saint Lucia, Saint Pierre and Miquelon, Saint Vincent and the Grenadines, Saudi Arabia, Senegal, Seychelles, Sierra Leone, Somalia, South Africa, Sri Lanka, Suriname, Svalbard and Jan Mayen, Swaziland, Taiwan, Tajikistan, Tanzania, Togo, Trinidad and Tobago, Tunisia, Turkmenistan, Turks and Caicos Islands, US Protectorates, Uganda, Ukraine, United Arab Emirates, Uzbekistan, Vatican City State, Venezuela, Vietnam, Virgin Islands (U.S.), Western Sahara, Yemen, Zambia, Zimbabwe

All orders are processedwithin 24 hoursafter they are placed. Usually, we are able to ship orders the next day. Weekend orders are shipped on the following Monday. You will receive a shipping confirmation email from our system when the shipping information has been uploaded.

Generally, we will ship the orders with Free Shipping, without the minimum order amount requirement. You may check if the free shipping method is available to your country in the Delivery Area below.

Austria, Belgium, Czechia, Denmark, Finland, France, Germany, Greece, Hungary, Italy, Lithuania, Luxembourg, Monaco, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey, Ukraine, United Kingdom, etc.

Easy Peasy! Log into your account through the online store, check out the fulfilment status against your recent order. If the order has been fulfilled, click onto the order information & you can find your tracking information here.

As soon as your order is packed and shipped, you"ll receive a shipping confirmation email. You will then be able to track your order through the tracking link on the email. If you haven"t received an email yet, please reach out to us atservice@sunfounder.com, our sales staff will contact you ASAP.

* Delivery Time - These are the delivery estimates provided by our shipping partners and apply from point of dispatch, not from point of sale. Once your parcel leaves our warehouse, we cannot control any delays after that point.

Such as the products you buy on our site - can"t simply be shipped freely from country to country. When goods are imported into a different country or customs territory, there is a charge called Customs Duty that must apply. This is charged by the local customs authority where the goods are being imported into.

If Customs Duty is payable to your territory, you"ll be responsible for paying it to the authorities, so SunFounder isn"t involved in this process. Whether Customs Duty is payable, and by how much, depends on a whole lot of different things. For example, many countries have a "low value threshold" below which they do not charge any Customs Duty.

If you do have to pay Customs Duty though, the amount payable is usually calculated based on the value of the goods and the type of goods being imported.

If, for whatever reason, you refuse the customs fee and the parcel is returned back to us. If you"re still unsure on whether you"ll be subject to customs fees, we recommend contacting your local customs office for more info before placing your order!

Inky wHAT is a 400x300 pixel electronic paper (ePaper / eInk / EPD) display for Raspberry Pi, a larger version of our popular Inky pHAT display, with more than 5x the number of pixels, and available in three colour schemes - red/black/white,...

Build a full-featured media center capable of playing nearly all of your digital media using any 40 pin Raspberry Pi and the Media Center HAT Raspberry Pi touchscreen display. Native support in...

Inky wHAT is a 400x300 pixel electronic paper (ePaper / eInk / EPD) display for Raspberry Pi, a larger version of our popular Inky pHAT display, with more than 5x the number of pixels - red/black/white version.

If you"re looking for the most compact li"l color display for a Raspberry Pi B+, Pi 2, & Pi 3 (most likely a Pi Zero) project, this might be just the thing you need!

In honour of Raspberry Pi"s 10th birthday, we"ve fused a RP2040 microcontroller with an EPD display to make a stylishly monochrome, maker friendly, e-paper badge(r)...

Pico Inky Pack features the speedy 2.9" e-paper display that you can find on Badger 2040, coupled with three handy buttons for interfacing. Equip it to the back of your...

Waveshare 21435 - 2.8″ Touch Screen Expansion For Raspberry Pi Compute Module 4, Fully Laminated Display, Gigabit Ethernet, USB2.0, Optional Interface Expander

In honour of Raspberry Pi"s 10th birthday, we"ve fused a RP2040 microcontroller with an EPD display to make a stylishly monochrome, maker friendly,...

Crisp, high-res, with great viewing angles (IPS), this 1.3" square, 240x240 pixel, colour LCD will add some pizzazz to your Raspberry Pi or Arduino projects.

A TFT touch screen combines the fundamental elements of a raspberry pi touch screen with the advanced imagery TFT technology. These are the variants of raspberry pi touch screen displays that most consumers see and use on a daily basis. While TFT displays use more energy than standard monochrome LCD displays, many models provide brighter and more detailed visuals than conventional screens.

Explore the extensive selection of wholesale raspberry pi touch screen LCD displays, TFT, and HMI that can be used across a range of industries, including domestic, medical, industrial, automotive, and many others. You can choose from a number of standard industry sizes and find the raspber p i touch screen that are applicable to your required use. If you would like options that allow a smaller environmental footprint due to low power consumption, you can browse the Chip-on-Glass (COG) LCDs. COGs are designed without PCBs so have a slimmer profile.

Alibaba.com features a broad collection of smart and advanced raspberry pi touch screen equipped with bright, capacitive screens for the most affordable prices. These raspberry pi touch screen are made implying the latest technologies for a better, enhanced, and smart viewing experience. These products are of optimal quality and are sustainable so that they can last for a long time. Buy these raspberry pi touch screen from the leading wholesalers and suppliers at discounted prices and fabulous deals. The smart and capacitive raspberry pi touch screen offered on the site are applicable for all types of ads displaying, mobile screens, LCD monitors, and many more. You can use them both for commercial as well as residential purposes. These marvellous raspberry pi touch screen are provided with bright and strong backlights available in distinct colors for a wonderful screen viewing experience. These raspberry pi touch screen are.

This small 3.5-inch touch screen module is designed especially for Raspberry Pi, using the latest Linux Core system. This is ideal for DIY anywhere, anytime and does not require any separate power source or case to hold it. The module sits right on top of Pi. The screen also comes with a stylus to interact with the small screen.

This website is using a security service to protect itself from online attacks. The action you just performed triggered the security solution. There are several actions that could trigger this block including submitting a certain word or phrase, a SQL command or malformed data.