low cost arduino lcd displays pricelist

ER-TFTMC050-3 is 800x480 pixel 5" color tft lcd display with small controller board,superior display quality,super wide viewing angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO, and ARM .It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.

It supports 8080 6800 8-bit,16-bit parallel,3-wire,4-wire,I2C serial spi interface.It"s optional for resistive touch panel and capacitive touch panel with controller,optional arduino shield with library and example and optional for power supply.

This LCD Display Shield gives you a nicely mounted 1602 LCD Display snaps right on top of your Arduino UNO. With onboard buttons for easy navigation including up, down, left, right, select and reset, using your Arduino away from a computer was never easier. Use this shield to display values read in by your Arduino, display options for user inputs, choose between different programs you can run on your Arduino, etc. With a Power LED onboard and a nice blue backlit display, you"ll be able to use your Arduino"s LCD Display Shield day or night!

This shield is compatible with the "LiquidCrystal" library that is bundled with the Arduino software. Just edit the "LiquidCrystal" library"s default mapping from the LCD pins to Arduino pins to the ones for this specific shield by copying what"s shown below. Here is an example of the proper way to instantiate the LiquidCrystal class for this shield:

Liquid crystal displays (LCDs) and LED displays offer a convenient and inexpensive way to provide a user interface for a project. This chapter explains how to connect and use common text and graphical LCD/LED panels with Arduino. By far the most popular LCD is the text panel based on the Hitachi HD44780 chip. This displays two or four lines of text, with 16 or 20 characters per line (32- and 40-character versions are available, but usually at higher prices). A library for driving text LCD displays is provided with Arduino, and you can print text on your LCD as easily as on the Serial Monitor (see Chapter 4), because LCD and serial share the same underlying print functions.

LCDs can do more than display simple text: words can be scrolled or highlighted and you can display a selection of special symbols and non-English characters.

You can create your own symbols and block graphics with a text LCD, but if you want fine graphical detail, you need a graphical display. Graphical LCD (GLCD) and graphical LED displays are available at a small price premium over text displays.

Graphical displays can have more wires connecting to Arduino than most other recipes in this book. Incorrect connections are the major cause of problems with graphical displays, so take your time wiring things up and triple-check that things are connected correctly. An inexpensive multimeter capable of measuring voltage and resistance is a big help for verifying that your wiring ...

General Specification NMLCD-24QA is a colour active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor). It is composed of a colour TFT-LCD panel, driver IC, FPC and a back light unit and with a Resistive Touch...

General Specification NMLCD-24240320-CLB is a colour active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor). It is composed of a colour TFT-LCD panel, driver IC, FPC and a back light unit and without a Touch...

NMLCD-24240320-RTP is a colour active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor). It is composed of a colour TFT-LCD panel, driver IC, FPC and a back light unit and with a ...

General Specification NMLCD-24240320-RTP is a colour active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor). It is composed of a colour TFT-LCD panel, driver IC, FPC and a back light unit and with a...

NMLCD-24240320 is a colour active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor). It is composed of a colour TFT-LCD panel, driver IC, FPC and a back light unit and without a Touch...

NMLCD-24240320-CLB is a colour active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor). It is composed of a colour TFT-LCD panel, driver IC, FPC and a back light unit and without a Touch...

General Specification NMLCD-24QA is a colour active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor). It is composed of a colour TFT-LCD panel, driver IC, FPC and a back light unit and with a Resistive Touch...

General Specification NMLCD-24240320 is a colour active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor). It is composed of a colour TFT-LCD panel, driver IC, FPC and a back light unit and without a Touch...

General Specification NMLCD-24240320 is a colour active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor). It is composed of a colour TFT-LCD panel, driver IC, FPC and a backlight unit and with/without a...

Microcontrollers (MCUs) have a few display options available. A Liquid Crystal Display (LCD) is a common, low-cost option that uses a backlight made of either cold-cathode fluorescent tubes (CCFL) or light emitting Diodes (LEDs). The term “LED display” actually refers to an LCD display with LED backlighting, and thus is the same thing as an “LCD Display.” Another display option is the Organic Light-Emitting Device (OLED), which emits light in a manner similar to LEDs and therefore does not require a separate backlight. An LCD has many more components than OLED displays, and for example might include a light guide panel and a diffuser to evenly disperse the light emitted from the backlight across the whole screen, liquid crystal shutters that switch the light on and off throughout the display, polarizing film and other components to drive the LCD shutters and reflect the backlight (although manufacturing components and techniques may vary).

Many microcontrollers have built-in circuitry for display drivers so that the MCU can directly control the display or segments in a display. Controlling a display with an MCU is relatively easy if the display is a simple segment-driven (e.g., text-only), monochrome display. Several MCUs include a software library for operating LCD displays, which will be driver-specific. Find the software library that matches the hardware that drives the LCD display. Sometimes off-brand hardware display drivers will be compatible with other display drivers that are already in wide use so you can still use the software library for the compatible driver. Expect to use several pins for data and power for the backlight that should be included with a segment-driven display. According to the Arduino site, which offers LiquidCrystal software libraries, the Hitachi HD44780 driver has a 16-pin interface. Some MCUs use SPI or I2C to drive an LCD or OLED display. Small OLED displays have become fairly affordable and make sense if you have a strict power budget. See Table 1 for comparison of OLED and LCD to make the best choice for your design.

PROs: LCD displays are thicker and heavier than OLED displays and consume more power than OLEDs, due to the need for a backlight. OLEDs have self-emitting light and do not require backlights. However, OLED displays do not put out as much light as an LCD/LED display. (E.g., all things being equal, an OLEDdisplay as a flashlight is not as effective as your smartphone’s LED display screen in a dark room.) Without a backlight, OLED displays do not leak light when black areas are shown on the OLED display, unlike LCD displays. With OLED displays, each pixel that is set to black is going to be really black. OLEDs, being self-emitting light sources, are also controllable down to the pixel. LCD displays cannot control each pixel, but control in regions. OLED technology is newer than LCD and therefore more expensive, but prices are dropping as OLED technology matures. OLED has a superior viewing angle; the picture does not diminish as you view the screen to 80 degrees or more off center, whereas LCDs lose visibility at around 50 degrees.

CONs: OLED displays can lose their brightness over long-term use, but the technology is improving with time. It is also technically possible for OLEDs to suffer long-term image retention (also known as “burn-in,” an inaccurate term for OLEDs borrowed from CRTs) under extreme conditions. However, OLEDs do not use phosphor coating as CRTs did, so burn-in is not necessarily permanent. The potential for burn-in makes OLED displays used for digital signage a poor candidate, especially if the display image is extremely bright, high-contrast, and never varies (at the pixel level), or if the OLED display is not set up with some screen preservation features. LG claims that OLED TV screens come with built-in features to avoid burn-in, such as pixel-shifting an image, termed “Screen Shift” by LG, which “moves the screen slightly at regular intervals to preserve picture quality.” LG also claims that the quality of an OLED image can be preserved “by resetting the TV so it clears the pixels.”[i] Unlike CRTs, for which long-term image retention is permanent once it’s there (and monochromatic), OLED screens experience an erasable, multi-color long term image retention. Therefore, OLED “burn-in” isn’t the same kind of permanent burn-in that CRTs can experience. Long-term image retention on an OLED screen can be “erased” by playing varying content on the OLED screen for a while.[ii] DIY digital signage with a static image on an OLED display is not recommended, however. Major manufacturers like Samsung and LG offer OLED displays for digital signage but include features to avoid long-term image retention.

3.2 Inch TFT LCD Touch Screen Display V4.0 for Raspberry PiFeatures320x240 hardware resolutionResistive touch controlSupports any revision of Raspberry Pi (directly-pluggable)Drivers provided (works with your own Raspbian/Ubuntu/Kali)Supports FBCP software driver as well, allows to config software r..

In electronics world today, Arduino is an open-source hardware and software company, project and user community that designs and manufactures single-board microcontrollers and microcontroller kits for building digital devices. Arduino board designs use a variety of microprocessors and controllers. The boards are equipped with sets of digital and analog input/output (I/O) pins that may be interfaced to various expansion boards (‘shields’) or breadboards (for prototyping) and other circuits.

The boards feature serial communications interfaces, including Universal Serial Bus (USB) on some models, which are also used for loading programs. The microcontrollers can be programmed using the C and C++ programming languages, using a standard API which is also known as the “Arduino language”. In addition to using traditional compiler toolchains, the Arduino project provides an integrated development environment (IDE) and a command line tool developed in Go. It aims to provide a low-cost and easy way for hobbyist and professionals to create devices that interact with their environment using sensors and actuators. Common examples of such devices intended for beginner hobbyists include simple robots, thermostats and motion detectors.

In order to follow the market tread, Orient Display engineers have developed several Arduino TFT LCD displays and Arduino OLED displays which are favored by hobbyists and professionals.

Although Orient Display provides many standard small size OLED, TN and IPS Arduino TFT displays, custom made solutions are provided with larger size displays or even with capacitive touch panel.