electric scooter lcd display manual supplier

Unit: MPH, KM/H. A speed signal comes from the motor via controller to the display. The indicated speed depends on the motor signal and the wheel diameter.

When riding the scooter, keep the acceleration handle pressed with the same pressure for 5 seconds to activate the cruise control mode. Use the brake handle to deactivate the cruise control mode.

For safety purposes, all Joyor models except Mbike model are set by default to non-zero start mode, which means the motor will not get started until you start to kick the scooter first so that the speed is above zero:

The display is equipped with a USB port for you to be able to charge your electronic devices. When the device is connected, the USB indicator is lit. In case of problem, the indicator starts to flash, and a safety mode will be automatically activated.

5. LCD Display Meter: the motor brushless controller kit with LCD display meter, which can clearly display status and data, and is suitable for 22.5mm handlebar.

The function can be achieved by connecting the display jack to the controller instrument interface. If you want to connect other accessories, please refer to the manual.

P1 (fixed) -This will usually be fixed by default, there shouldn"t be a need to change this. Shows the voltage of the battery (Under-voltage point of the battery will be displayed) E.g. Under voltage point will be 31.5V if you"re seeing 315 on the display.

Important to note: If you are using EMOVE Cruiser, the maximum voltage is 52V - if your P2 settings is set lower than default, it might show that your battery only has 3 bars when in fact it is actually full. To the LCD display computer, it will be seen as full.

Yes! It may happen, you may find your electric scooter is not working properly. You were up for a nice and refreshing ride but suddenly you found out the electric scooter’s motor is not working properly. Surely you should maintain your electric scooter very carefully. Generally, electric scooters are durable and built to last for a long time. They also required minimum maintenance. But like other vehicles, the electric scooters have parts and components that are sensitive to damage. The damages may come from overuse, overcharging, and stress due to extreme riding activities causing various outcomes like- malfunctioning, melting or even burning different parts of the electric scooters. After reading this article you’ll have at least some basic knowledge of how to fix an electric scooter or you may become an expert on this! So, try to read the whole article diligently.

The electric scooters use different types of motor, mainly- the hub motor or the electric motor. The motors are generally incorporated to the rear or front wheel. This doesn’t change the basic structure or design of the scooter. The motors are very easy to install and access for service and repair. You can also turn off the motor and run your electric scooter like a kick scooter. The motor just moves along with the wheel without any influence on the motion.

Knowing the types of motor that your electric scooter using will definitely make you proactive. To maximize the performance of your electric scooter you have to take a very good care of the motor also along with the scooter.

As it may happen, you may spend a lot of time to find out what actually happened to your electric scooter. You may try to fix the problem but you found out that you have no idea what or where the problem is. Here we are mentioning five general tips and guidelines-

First, you can check for any disconnected or loose wires by smoothly pulling the wires one by one and try to find out is there anything burnt or melted. But be careful, they should not be disconnected. Try to check all wires or wire connectors that connect to the motor. Or you can smell the motor, speed controller and other electrical components.

If the electric scooter does not run check the motor because the motor is the power source. Because of excessive riding or doing stunts may cause the problems. Check the battery charger too. Connect it to the port and look for the indicator. If the indicator does not work properly change the charger and then try again.

Check the electric scooter’s fuse or the circuit breaker. The fuse may get burnt due to many reasons like- overheating, overcharging. You can check the fuse or circuit breaker by multi-meter.

Test your electric scooter’s throttle. You can use the 4.5-5V DC power source and multi-meter. Sometimes the throttle causes the problem. If you cannot use the multi-meter seek help from an expert. If there is a problem with your throttle the multi-meter will detect it. And if the problem arises you should get the throttle fixed.

If your scooter does not work try to move the power switch or key switch between the “on” and “off” position several times. If you find that the switch is loose there may be a problem because of the switch. The problem with the switch can also be checked with the multimeter.

Finally, at the end of this article about how to fix an electric scooter, we hope you could gain a good amount of insights about your electric scooter. And we also hope that now you can fix your scooter’s general problems all by yourself and ensure better safety.

The Jetson Eris has a detachable device mount to add to the already big and bright LCD display. The electric scooter gets supercharged with next-gen innovation. With an updated motor, lighter frame, and integrated phone holder, the Eris has been built from the ground up for the ultimate riding experience.