arduino 5 tft lcd touch screen shield ra8875 price

Spice up your Arduino project with a beautiful large touchscreen display shield with built in microSD card connection. This TFT display is big (5" diagonal) bright (12 white-LED backlight) and colorfu 480x272 pixels with individual pixel control. As a bonus, this display has a optional resistive touch panel attached on screen by default.

The shield is fully assembled, tested and ready to go. No wiring, no soldering! Simply plug it in and load up our library - you"ll have it running in under 10 minutes! Works best with any classic Arduino (UNO/Due/Mega 2560).

This display shield has a controller built into it with RAM buffering, so that almost no work is done by the microcontroller. You can connect more sensors, buttons and LEDs.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!" - we"ve written a full open source graphics library at the bottom of this page that can draw pixels, lines, rectangles, circles and text. We also have a touch screen library that detects x,y and z (pressure) and example code to demonstrate all of it. The code is written for Arduino but can be easily ported to your favorite microcontroller!

For 5 inch screen,the high current is needed.But the current of arduino uno or arduino mega board is low, an external 5V power supply is needed. Refer to the image shows the external power supply position on shield ER-AS-RA8875.

If you"ve had a lot of Arduino DUEs go through your hands (or if you are just unlucky), chances are you’ve come across at least one that does not start-up properly.The symptom is simple: you power up the Arduino but it doesn’t appear to “boot”. Your code simply doesn"t start running.You might have noticed that resetting the board (by pressing the reset button) causes the board to start-up normally.The fix is simple,here is the solution.

Spice up your Arduino project with a beautiful large touchscreen display shield with built in microSD card connection. This TFT display is big (5" diagonal) bright (18 white-LED backlight) and colorfu 800x480 pixels with individual pixel control. As a bonus, this display has a optional resistive touch panel attached on screen by default.

The shield is fully assembled, tested and ready to go. No wiring, no soldering! Simply plug it in and load up our library - you"ll have it running in under 10 minutes! Works best with any classic Arduino (UNO/Due/Mega 2560).

This display shield has a controller built into it with RAM buffering, so that almost no work is done by the microcontroller. You can connect more sensors, buttons and LEDs.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!" - we"ve written a full open source graphics library at the bottom of this page that can draw pixels, lines, rectangles, circles and text. We also have a touch screen library that detects x,y and z (pressure) and example code to demonstrate all of it. The code is written for Arduino but can be easily ported to your favorite microcontroller!

If you"ve had a lot of Arduino DUEs go through your hands (or if you are just unlucky), chances are you’ve come across at least one that does not start-up properly.The symptom is simple: you power up the Arduino but it doesn’t appear to “boot”. Your code simply doesn"t start running.You might have noticed that resetting the board (by pressing the reset button) causes the board to start-up normally.The fix is simple,here is the solution.

ER-TFTM050-3 is 5 inch tft lcd module WVGA 800x480 display,serial,spi,i2c parallel interface,RA8875 controller,capacitive or resistive touch screen panel

which I"m looking to use with the Arduino Mega, to do this the datasheet say that logic level is 3.3V which means i need a logic level converter. So I"ve connected the Arduino Mega to the logic level converter then onto the screen SPI pins on the screen.

ER-TFTM050-3-4125 is 5 inch tft lcd display with RA8875 controller board,arduino shield,examples,library.Optional touch panel,arduino mega2560,due or uno board.

at the bottom of the page is an Arduino library for driving the graphics chip with the shield, from what i can see all the shield is just a logic level converter for the screen, I"ve got this from the schematics and my understating of Arduino logic.

So will the library that they supply with the shield work with the set up i have created? I cant see why it wouldn"t but when i connect it all up the screen is not working, its black but their is data on the pins on both side of logic level converter, I was using one of Buy Displays Arduino Mega examples that come with the library on the shield page, I"ve made sure I"ve changed the CS but its still not working and i cant see why it wouldn"t work.

I don"t actually have a display at present. I purchased a 7in one some months ago. It had an LT7381 controller and was supplied with a Hunda LT7381 library for Arduino and some basic display design software. However, I couldn"t get the hardware to work despite it being described as Arduino compatible. As it turned out, it also didn"t display anything when used with the supplied USB adaptor and design software for the PC, so it may have been faulty anyway. I posted something at the time but the controller is quite new and there was not much feedback. I ended up sending it back and getting a refund although it still cost me to send it back to china.

The reason I posted was because the project is now at the stage where the LCD display really needs to be added and I intended to get advice before making another purchase. In the meantime I have been working on the project using a 20x4 display.

I don"t posses an Arduino shield which is why I was trying to ascertain whether I need something like that. What is their purpose? A lot of photos show the display plugged into one and then into typically a Mega 2560. I don"t understand what the purpose of the shield is? Is it just a convenient way to provide a means of fitting the board to an Arduino with level shifting? SPI needs only 4 wires. Can"t these be connected directly to the ESP SPI pins?

I have had great/fairly painless results using the larger 4 and 5 inch displays from BuyDisplay, however these use an RA8875 display driver and sheild.

I need a bit smaller and less power hungry unit for my next project, so i ordered up the 3.5 inch, 480x320 display (and sheild) that uses the ILI9488 driver with the CAP touch option.

I"ve used this size display from cheaper sources, but most of these only come with a resistive touch panel and they don"t look all that great. Those use the SPI interface.

ER-TFTM035-6-4123 is 3.5 inch tft lcd display with adaptor board,ILI9488 arduino shield,examples,library.Optional touch panel,arduino mega2560.due board.

The example code compiles and loads just fine on the DUE, however i simply cannot get the TFT to work. The CAP touch seems to work fine, and reports touches to the serial terminal, but the screen remains white no matter what.

The included example uses the UTFT library, and, as I have yet to find a tutorial on using the library, i"ve just dug into the examples and the library .H files to try and sort out how to use it. As near as i can tell, the UTFT library supports many different typed of displays and SPI/parallel modes. so to initialize the display you put something like

So I set about checking the wiring diagram for both the shield and the display module, double checking the jumpers and trying to sort out the various pins."

As near as i can tell, both the display module and the shield are set up for the 16 bit parallel interface, but where it gets confusing is the shield schem doesn"t look like it matches up with the example code. for starters, the shield jumpers are not labeled like they are in the schem, and, according to the scem, pins 25-28 are used for the data bus, not the control pins. The control pins look to be on 7,8,9,and 10, but as there are several jumpers, and jumpers from jumpers, and they are not labeled on the shield, Im going in circles. add that to the fact that the Scem doesnt show the RS or WR pins, and alternate names need to be assumed ( RS=DC=A0 ) and there are at least 2 DC pins on the schem, a couple W\R options.

Im pretty sure, if Im to believe the scem, that arduino pins 9 and 10 are CS and RST respectively, but the RS and WR pins could be any combination of arduino pins

Has anyone gotten this to work? I may have another display i can try, possible i have a bad one, but the more i dig into this the more i think im just not setting the control pins right, or not initializing the tft correctly. Would realy like to use this display, and keep the 16 bit mode, i care much more about speed than pins.

7" inch TFT LCD Resistive Touch RA8875 Shield for Arduino Due,MEGA 2560 Uno. Refer to the. Spice up your Arduino project with a beautiful large touchscreen display shield with built in microSD card connection. This TFT display is big (7" diagonal) bright (21 white-LED backlight) and colorful (16-bit 262,000 different shades)! Description Spice up your Arduino project with a beautiful large touchscreen display shield with built in microSD card connection. This TFT display is big (7" diagonal) bright (21 white-LED backlight) and colorful (16-bit 262,000 different shades)! 800x480 pixels with individual pixel control. As a bonus, this display has a resistive touchscreen attached to it already. The shield is fully assembled, tested and ready to go. No wiring, no soldering! Simply plug it in and load up our library - you"ll have it running in under 10 minutes! Works best with any classic Arduino (UNO/Due/Mega 2560). This display shield has a controller built into it with RAM buffering, so that almost no work is done by the microcontroller. You can connect more sensors, buttons and LEDs. Of course, we wouldn"t just leave you with a datasheet and a "good luck!" - we"ve written a full open source graphics library at the bottom of this page that can draw pixels, lines, rectangles, circles and text. We also have a touch screen library that detects x,y and z (pressure) and example code to demonstrate all of it. The code is written for Arduino but can be easily ported to your favorite microcontroller! For 7 inch screen,the high current is needed.But the current of arduino uno or arduino mega board is low, an external 5V power supply is needed. Refer to the image shows the external power supply position on shield ER-AS-RA8875. For people who want the same screen but not in a shield form-factor, check out our 7" TFT breakout. What"s included in the package Num Standard Accessory Name Qty 1 7"TFT Display with Resistive Touch Panel and RA8875 Controller Board 1 2 Arduino Shield 1 * The default power supply is 5V and the default interface is 4-wire serial interface. Compatible with Following Arduino Boards Board Name MCU I/O Arduino MEGA2560 ATMEGA2560 54 Arduino Due AT91SAM3X8EA 54 Arduino Uno ATMEGA328 14 * Please buy separately if you need the arduino boards. Ebay doesn"t allow listings to contain external links,so the documents link may be invalid. Please copy the below entire link to your browser for checking our documents(at the bottom of the page) or for bulk order. https://www.buydisplay.com/default/serial-spi-arduino-7-inch-tft-lcd-touch-shield-ra8875-for-mega-due-uno Datasheet for TFT LCD Module,Controller Format Documents Name (Downloadable) Version Language Update Date Size 7"800x480 Dots TFT LCD Module withController Board Datasheet 1.0 English Dec-04-2013 926K Controller IC RA8875 Datasheet 1.0 English Jul-31-2013 2.3M Datasheet for Resistive Touch Panel Format Documents Name (Downloadable) Version Language Update Date Size 7 inch 4-Wire Touch Panel Datasheet 1.0 English Feb-02-2013 247K Datasheet and Schematic for Arduino Shield Format Documents Name (Downloadable) Version Language Update Date Size ER-AS-RA8875 Datasheet 1.0 English Mar-08-2016 767K ER-AS-RA8875 Arduino Schematic Diagram 1.0 English Jun-24-2015 195K Tutorial - Arduino Due (MEGA 2560,Uno)Libraries,Examples ↓ Format Documents Name (Downloadable) Version Language Update Date Size Libraries+Examples for 4-wire SPI 7"Capacitive Touch Shield 1.0 English May-17-2017 22K Libraries+Examples for 4-wire SPI 7"Resistive Touch Shield 1.0 English Dec-01-2016 58K Libraries+Examples for 4-wire SPI Micro SD Card or TF Card 1.0 English Dec-20-2016 1.6M About Us We"re China-based global display manufacturer named EastRising Technology Co.,Ltd. that has a worldwide business in design, produce and sell various displays for small to large companies since 2003. Our web site is [link removed by eBay] . Link for video and image of our production line and equipment. RoHS reports for all material we used on display module. Long Term Continuity Supply Warranty We promise the long terms continuity supply and would never end.Some controller IC may stop the production,we"ll try our efforts to find the completely compatible ones.If the equivalent is unavailable, we¡¯ll make the new tooling and use the most similar IC as replacement.So you don"t have to worry even your research time is very long. Shipping Policy All products will be checked carefully and packed in good condition before shipping.We e-mail all customers with tracking information immediately after the shipment for status tracking. Item will be shipped within 1 business day after the payment has been received. Customs fees and import duties for exports are buyer"s responsibility. Warranty All products are covered under our limited warranty, which provides all products are free of functional defects for a period of one year from the date of receipt and all products are free of visual defects and missing parts for a period of 30 days from the date of receipt.If a product was damaged during shipping or the order is incorrect,you must notify us within 2 days of receipt. How to return a product First request an RMA number from our sales with the information:part number,reason for return,order number. Our sales will then either issue an RMA number, ask you for more information, or offer to help you resolve a technical problem so that the product does not need to be returned. Products must arrive here in the same condition as when you received them. You are responsible for return shipping and insurance.Please make sure your RMA number is on the shipping label and on any documents you include with the product. After we receive the product, we inspect it to determine the cause of any defect, then update by email with our findings. This process usually takes five business days. Specification Gross Weight (kg)0.3710 ManufacturerEastRising Continuity SupplyWe promise the long term continuity supply for this product no less than 10 years since 2015. Part NumberER-TFTM070-5-4125 Display Format800x480 Dots Interface6800 8-bit Parallel , 8080 8-bit Parallel , 6800 16-bit Parallel , 8080 16-bit Parallel , I2C, 3-Wire Serial SPI, 4-Wire Serial SPI IC or EquivalentRA8875 AppearanceRGB on Black Diagonal Size7.0“ ConnectionPin Header, FFC-Connector Outline Dimension180.0(W)x104.0(H)mm Visual Area156.9x89.00mm Active Area154.08(W)x85.92(H)mm Character SizeNo Dot (Pixel) Size0.0642(W)x0.1790(H)mm Dot (Pixel) PitchNo IC PackageSMT Display TypeTFT-LCD Color Touch Panel OptionalYes Sunlight ReadableNo Response Time(Typ)20ms Contrast Ratio(Typ)500:1 Colors256/65K Viewing DirectionNo Viewing Angle RangeLeft:60.0 , Right:60.0 , Up:60.0 , Down:60.0 degree Brightness(Typ)200cd/m2 Backlight ColorWhite Color Backlight Current (Typ)No Power Supply(Typ)5V Supply Current for LCM(Max)480mA ( VDD=3.3V) / 300mA ( VDD=5.0V) Operating Temperature-20℃~70℃ Storage Temperature-30℃~80℃ Series NumberER-TFT070-4

Have you gazed longingly at large TFT displays - you know what I"m talking about here, 4", 5" or 7" TFTs with up to 800x480 pixels. Then you look at your Arduino. You love your Arduino (you really do!) but there"s no way it can control a display like that, one that requires 60Hz refresh and 4 MHz pixel clocking. Heck, it doesn"t even have enough pins. I suppose you could move to ARM core processors with TTL display drivers built in but you"ve already got all these shields working and anyways you like small micros you"ve got.

What if I told you there was a driver chip that could fulfill those longings? A chip that can control up 800x480 displays, and heck, a resistive touchscreen as well. All you need to give up is 5 or so SPI pins. Would you even believe me? Well, sit down because this product may shock you.

The RA8875 is a powerful TFT driver chip. It is a perfect match for any chip that wants to draw on a big TFT screen but doesn"t quite have the oomph (whether it be hardware or speed). Inside is 768KB of RAM, so it can buffer the display (and depending on the screen size also have double overlaying). The interface is SPI with a very basic register read/write method of communication (no strange and convoluted packets). The chip has a range of hardware-accelerated shapes such as lines, rectangles, triangles, ellipses, built in and round-rects. There is also a built in English/European font set (see the datasheet section 7-4-1 for the font table) This makes it possible to draw fast even over SPI.

The RA8875 can also handle standard 4-wire resistive touchscreens over the same SPI interface to save you pins. There"s an IRQ pin that you can use to help manage touch interrupts. The touchscreen handler isn"t the most precise driver we"ve used, so we broke out the X/Y pins so 11:54)

Have you gazed longingly at large TFT displays - you know what I"m talking about here, 4", 5" or 7" TFTs with up to 800x480 pixels. Then you look at your Arduino. You love your Arduino (you really do!) but there"s no way it can control a display like that, one that requires 60Hz refresh and 4 MHz pixel clocking. Heck, it doesn"t even have enough pins. I suppose you could move to ARM core processors with TTL display drivers built in but you"ve already got all these shields working and anyways you like small micros you"ve got.

What if I told you there was a driver chip that could fulfill those longings? A chip that can control up 800x480 displays, and heck, a resistive touchscreen as well. All you need to give up is 5 or so SPI pins. Would you even believe me? Well, sit down because this product may shock you.

The RA8875 is a powerful TFT driver chip. It is a perfect match for any chip that wants to draw on a big TFT screen but doesn"t quite have the oomph (whether it be hardware or speed). Inside is 768KB of RAM, so it can buffer the display (and depending on the screen size also have double overlaying). The interface is SPI with a very basic register read/write method of communication (no strange and convoluted packets). The chip has a range of hardware-accelerated shapes such as lines, rectangles, triangles, ellipses, built in and round-rects. There is also a built in English/European font set (see the datasheet section 7-4-1 for the font table) This makes it possible to draw fast even over SPI.

The RA8875 can also handle standard 4-wire resistive touchscreens over the same SPI interface to save you pins. There"s an IRQ pin that you can use to help manage touch interrupts. The touchscreen handler isn"t the most precise driver we"ve used, so we broke out the X/Y pins so you can connect them up to something like the STMPE610 which is a very classy touchscreen controller.

On the PCB we have the main chip, level shifting so you can use safely with 3-5V logic. There is also a 3V regulator to provide clean power to the chip and the display. For the backlight, we put a constant-current booster that can provide 25mA or 50mA at up to 24V. The connector to the screen is a classic "40 pin" connector. All the 40-pin TFT"s in the Adafruit shop are known to work well. There are other 40-pin displays that have different pinouts or backlight management and these may not work - they may even damage the driver or TFT if the boost converter pushes 24V into the display logic pins! For that reason, we only recommend the displays we"ve tested and sell here.

Each order comes with an assembled, tested RA8875 breakout and a stick of header. You"ll also need to purchase a 40-pin TFT screen. We currently have 4.3", 5.0" and 7.0" screens available.

To get you started we"ve written a graphics library that handles the basic interfacing, drawing and reading functions. Download the Adafruit RA8875 library from github and install as described in our tutorial. Connect a 40 pin TFT to the FPC port and wire up the SPI interface to an Arduino as described in the example code. Once started you"ll be able to see the graphic/text demo and then touch the screen to "paint". For more advanced details on what the RA8875 can do (and it can do a lot) check the datasheet.

Hi @Uup115 — thanks for highlighting an issue with Due operation. I don’t have a Due so haven’t had an opportunity to test with one yet, so it is likely there are some compatibility adjustments needed. I will order one right away.

635 arduino tft lcd products are offered for sale by suppliers on Alibaba.com, of which lcd modules accounts for 64%, lcd touch screen accounts for 14%.