3.5 tft lcd adafruit quotation

ER-TFTM035-6 is 320x480 dots 3.5" color tft lcd module display with ILI9488 controller and breakout board,superior display quality,super wide viewing angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO,ARM and Raspberry PI.It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.

It supports 8080 8-bit /9-bit/16-bit /18-bit parallel ,3-wire,4-wire serial spi interface.Built-in microSD card slot, optional 3.5" 4-wire resistive touch panel with controller XPT2046 and capacitive touch panel with controller FT6236, so you can detect finger presses anywhere on the screen and doesn"t require pressing down on the screen with a stylus and has nice glossy glass cover . It"s optional for font chip, flash chip and microsd card. We offer two types connection,one is pin header and the another is ZIF connector with flat cable mounting on board by default and suggested. Lanscape mode is also available.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!".Here is the link for 3.5"TFT Touch Shield with Libraries, EXxamples.Schematic Diagram for Arduino Due,Mega 2560 and Uno . For 8051 microcontroller user,we prepared the detailed tutorial such as interfacing, demo code and development kit at the bottom of this page.

Displays are one of the best ways to provide feedback to users of a particular device or project and often the bigger the display, the better. For today’s tutorial, we will look on how to use the relatively big, low cost, ILI9481 based, 3.5″ Color TFT display with Arduino.

This 3.5″ color TFT display as mentioned above, is based on the ILI9481 TFT display driver. The module offers a resolution of 480×320 pixels and comes with an SD card slot through which an SD card loaded with graphics and UI can be attached to the display. The module is also pre-soldered with pins for easy mount (like a shield) on either of the Arduino Mega and Uno, which is nice since there are not many big TFT displays that work with the Arduino Uno.

To easily write code to use this display, we will use the GFX and TFT LCD libraries from “Adafruit” which can be downloaded here. With the library installed we can easily navigate through the examples that come with it and upload them to our setup to see the display in action. By studying these examples, one could easily learn how to use this display. However, I have compiled some of the most important functions for the display of text and graphics into an Arduino sketch for the sake of this tutorial. The complete sketch is attached in a zip file under the download section of this tutorial.

As usual, we will do a quick run through of the code and we start by including the libraries which we will use for the project, in this case, the Adafruit GFX and TFT LCD libraries.

With this done, the Void Setup() function is next. We start the function by issuing atft.reset() command to reset the LCD to default configurations. Next, we specify the type of the LCD we are using via the LCD.begin function and set the rotation of the TFT as desired. We proceed to fill the screen with different colors and display different kind of text using diverse color (via the tft.SetTextColor() function) and font size (via the tft.setTextSize() function).

The Adafruit library helps reduce the amount of work one needs to do while developing the code for this display, leaving the quality of the user interface to the limitations of the creativity and imagination of the person writing the code.

It appears some TFT displays have the red and blue pixel elements swapped. This is rather odd because the default colour order is the same as the Adafruit libraries for that display.

Anyway, I have updated the master library driver files for the HX8357D display to permit the colour order to be defined in the setup file. By default the colour order is RGB (as in Adafruit libraries) but this can be changed to BGR. The Setup_15 header has been updated with the following two lines:

Are you looking for a 3.5" TFT Display to add to your product or project? We"ve got a handful of different TFTs with a 3 1/2 diagonal dimension. Most of them support 16-bit Parallel, 18-bit Parallel, 8-bit Parallel, 9-bit Parallel, RGB, and SPI. While all TFTs are transmissive, we carry some that are bright enought to be sunlight-readable. As you can see we offer a variety of pixel densities for this size, 480x640, 320x480 and 320x240. If you"re looking for a different 3.5 inch TFT display that isn"t listed here, please contact our support team, they"d love to help you find the perfect display for your requirements.

The PiTFT Plus is a 480 x 320, 3.5 inch touchscreen TFT that has been designed for use with the Raspberry Pi Zero, Pi 2, 3 & 4 and models A+ and B+ (any Pi with a 2 x20 connector). The 16-bit colour pixels and resistive touch overlay make this display a valuable addition to any Raspberry Pi project, where it can be used as a console, X window port, displaying images or video etc.

A custom kernel package based on Notro"s awesome framebuffer work has been created which can be installed over existing Raspbian (or derivative) images using just a few commands. Adafruit provide a free tutorial and software installation guide to help you get the most out of your new, touchable TFT screen.