lcd display leak manufacturer

Scientists have discovered that LCD screens leak chemicals into just about every environment where they are found, according to a new study, and these particles have the potential to be toxic over time.As described in a study published last week in Proceedings of the National Academy of Sciences, researchers collected dust samples from seven buildings in China: a cafeteria, student dorm, classroom, hotel, home, lab, and an electronics repair shop. Nearly half of the 53 samples tested positive for liquid crystal particles—which are supposed to stay sealed in the screen after manufacturing—even in places where there were no LCD devices at the time of collection.AdvertisementThe international research team analyzed 362 chemicals used in LCD screens and found that nearly 100 have the potential to be toxic. These particles don’t break down quickly and have "high mobility" in the environment. When inhaled or ingested, according to the study, these particles can build up in the body over time with toxic effects, potentially causing digestive problems and other health issues.“These chemicals are semi-liquid and can get into the environment at any time during manufacturing and recycling, and they are vaporized during burning,” said University of Saskatchewan environmental toxicologist and lead author John Giesy in a press release. “Now we also know that these chemicals are being released by products just by using them.”According to the study, these chemicals are "simply filled" into the space between polarizers (light filters) during manufacturing and are not chemically bonded to any base material. This means that "they can be released during production; through wastewater; or during active use, disposal, or recycling."To be clear, the researchers didn"t observe any adverse health effects from the accumulation of liquid crystals in the human body; they only found that these crystals do in fact leak from devices, and that they have the potential to be toxic.

Stockwell Elastomerics is a leading provider of gaskets for touch screens, displays and integrated touch panel assemblies that serve several functions: sealing, load distributing, gap filling, mechanical shock protection and over-press cushioning.

Often a touch screen gasket or display gasket will help spread the compression load of the housing or bezel on the display. Without a gasket, the enclosure that holds the display in place can create pressure points on the display. In some cases, these pressures can cause distortions, false contacts or short circuits.

Similar to load distributing, touch panel gaskets are used to fill gaps between the screen and the display and/or the screen and bezel. The display gasket will take up gaps generated by tolerance stack-ups in the device.

Display gaskets offer some degree of cushioning to protect the display from damage due to mechanical shock. In the event that a device is dropped or banged, the gasket will act as a touchscreen cushion, offering a limited amount of protection.

Touchscreen gaskets also serve as display cushions when a user presses on the display too hard. The gasket deflects, takes up and spreads the load offering some protection from over-press or overloading in a small area.

LCD dust seals and touch screen dust seals are the most basic requirement of display gasketing. These are often static (not portable), indoor applications where the device is not to be exposed to water. Sealing can be achieved by closed cell sponge materials or fine pore open cell materials such as PORON urethane foam.

Outdoor displays such as outdoor information kiosks, ATMs and remote monitoring equipment require more design consideration. To contend with environments such as direct or wind-driven rain, sealing an enclosure, case or housing from ingress requires the proper material as well as proper compression on the gasket. Silicone foam or silicone sponge materials are preferred. Silicone gaskets remain flexible at low temperatures allowing for continued sealing against melting ice and snow as well as protecting against mechanical shock where many other materials will firm up in the cold and transfer energy. Other key features are: closed cell structure, low-stress relaxation, UV and ozone resistance, and general long life.

Light leaking is sometimes a concern with certain LCD or LED display applications. This can be addressed with black gasketing with either a very thin adhesive or a black supported adhesive. A common material configuration for this is soft PORON urethane foam with 3M 9795B adhesive. The 3M 9795B is a film supported double coat adhesive with a black PET support layer that does not pipe light.

Touchscreen gaskets and display gaskets tend to have narrow walls that don’t always lend themselves to easy installation. This can be addressed in a few ways such as fixturing or utilizing the centers as temporary supports. The preferred adhesives for touchscreen gaskets and display gaskets are repositionable adhesives such as Adchem 8311M or 3M 9415 depending on the bond strength required. Stockwell Elastomerics also offers medium and high bond strength adhesives for permanent bonding. View the current listing of pressure sensitive adhesive options.

Broad recommendations such as “closed cell foam” do not take into consideration factors such as stress relaxation, compression set, long term sealing performance, outgassing, plasticizer interaction, cost, and manufacturability. Over-designing the gasket can drive the cost up, whereas under designing could result in damaged devices and leaks when the units are in the field. Stockwell Elastomerics can offer guidance on design and manufacturability of touchscreen gaskets or touch panel gaskets. Key design points include:

It is important to keep in mind the clamping loads. While wider gasket walls generally seal better, the overall surface area is directly related to the loads applied to the LCD and touchscreen. Compression Force Deflection curves of various materials are available to aid designers.

The gasket thickness will depend on the designed gap in the enclosure, the fastening scheme, rigidity of the housing and the level of sealing required. Many touch screen gaskets are thin and soft but as the display gets larger the tolerance stacks typically get larger as well. This may require a thicker gasket depending on the fastener locations.

Some OEMs and contract manufacturers prefer to have the center of the gasket remain in place, held in place with small, breakaway tabs. Leaving the centers intact allows for easier positioning on the display when a fixture is not being used. Low tack, clean peeling adhesive is needed.

LCD screen display with two polarized materials, between them is a crystal crystal solution. In the use of many users will encounter liquid crystal screen leakage problems, most users are no clue to this, do not know how to do Today, Xiao Bian gave you popular LCD screen leakage of the repair problem, the way to teach you how to maintain the LCD screen.

Seal damage: the main will appear in the screen of the four edge position, if the beverage, fruit juice, soft drinks, tea and other acid-base liquid accidentally from the outside into the screen edge of the soak, it will cause damage to the sealant, inside the LCD Leakage. Screen in the production process if the sealant problems, the same will appear such a failure.

Screen surface by external damage: generally concentrated in the middle of the screen position, can see the obvious signs of glass cracks, then hand pressure leakage parts, you can see the movement of liquid crystal trajectory along the direction of movement.

Physical phenomena: Notebook or liquid crystal display surface has a very obvious block of dark spots (in the case of power), or there are light and dark uneven patches (in the case of no power) at the same time there are cracks. Individual LCD screen due to external force is not too large, although the liquid crystal screen caused by leakage, but the surface does not produce cracks, the fault is not easy to find, especially in the case of liquid crystal display power is not bright to pay attention. After the liquid crystal display breaks the leak, the image can still be displayed. At the same time after the liquid crystal screen leakage test machine will not produce a new fault, we do not have to worry.

Causes and repair: liquid crystal display by external force extrusion or impact, resulting in liquid crystal screen rupture and leakage phenomenon. Solution and maintenance costs: This type of failure is a very clear man-made physical damage, because the display accidentally squeeze or child with a finger press, it may be caused by the impact of the transport process. LCD screen damage to the higher maintenance costs for the LCD screen if the LCD screen is generally not damaged, because the cost of replacing the LCD screen is close to the cost of a model with the same type of liquid crystal display.

Established in 2002, Sinda Display Technology Co.,Ltd has devoted itself to the manufacturing and development of high-quality industrial display products...

There are very obvious massive black spots on the surface of the long bar LCD screen, or there are uneven patches of light and dark and cracks at the same time. The liquid crystal display is squeezed or impacted by the external force, resulting in the liquid leakage phenomenon caused by the rupture of the liquid crystal screen. The external force is not too large, although the liquid crystal screen leakage, but there is no crack on the surface, this fault phenomenon is not easy to find, especially in the case of LCD power is not bright. After the liquid crystal display ruptures the leak, the image can still be displayed.

Strip liquid crystal screen leakage is physically damaged, and the liquid crystal screen is cut and manufactured as a whole, once the leakage will slowly expand, or even can not display normally, which is irreparable unless the entire screen is replaced. But in terms of the cost of making liquid crystal displays, the screen accounts for 2/3, so it"s not cost-effective to replace the screen, so it"s better to buy a new monitor.

The control and drive circuit in the bar display module is a low-voltage, micro-power CMOS circuit, which is easy to be breakdown by static electricity. Electrostatic breakdown is a kind of irreparable damage, which must be paid attention to and should not be careless. Therefore, the display screen in the operation, assembly and use should be careful, to strictly prevent static electricity.

It is best to add a gasket of about 0.1 mm between the bar display module and the front panel, and the panel should also be flat to avoid distortion after assembly.

A maintenance film is affixed to the surface of the installed bar display screen to prevent defilement of the appearance during assembly, so it should not be removed before the whole machine is assembled, so as not to stain or damage the appearance surface.

The above is how to maintain the whole content of the bar LCD screens, I hope that we can learn the method of maintenance, so as to prolong the life of the LCD screens. If you want to purchase bar lcd screens, please contact us by email to

-To be clear, the researchers didn’t observe any adverse health effects from the accumulation of liquid crystals in the human body; they only found that these crystals do in fact leak from devices, and that they have the potential to be toxic. “We don’t know yet whether this a problem, but we do know that people are being exposed, and these chemicals have the potential to cause adverse effects,” said Giesy.

-If you crack LCD screens and find the liquid crystal leakage, don’t panic. Just remember that the liquid crystal materials might not be more toxic than your detergents for stove or washroom. Just wash your hands with soup throughout. Never try to play with it or even worse to taste it. The liquid of the cracked computer screen will not evaporate, no emissions worries.

-Any electronics has environment impact and can’t be used landfills. If you want to get rid of old LCD monitors or LCD TVs, give them to electronic collection stations. Let’s the professionals to handle them. They will extract some precious metals/parts and make them into something useful or at least not hazard. FYI, liquid crystal materials are retrievable.

I used to work for a laptop manufacturer doing support, and we were instructed that in the event that a customer ever called reporting a leaking LCD we were to IMMEDIATELY tell them to hang up the phone, call emergency services, and get a hazmat team onsite, while we escalated the call to our internal dedicated safety response team. That seems like a pretty harsh response (it"s more severe than what I would have been expected to do for anything short of "My laptop set my house on fire") so I"m inclined to think this stuff isn"t especially safe. It may be true that it"s only a hazard if ingested, though; based on my semi-limited knowledge of the chemistry involved that seems possible. If it were me, though, I"d take the extra cautious route just in case.

(In practice, this basically never happens short of a severe puncture like a blade would cause because of the way these things are manufactured. I"ve actually never personally heard of a situation where an LCD was leaking short of taking a bullet.) EDIT: Let me just make this stronger. This hardly ever happens, ever, anywhere, ever - it"s designed to prevent exactly this sort of problem. Unless you actually witness it in action there is probably no reason to worry about it. See further discussion in comments.

Long-time display manufacturer Samsung Display will likely stop the production of LCD displays this year. A recent report says several factors have influenced the South Korean firm’s decision.

Samsung has been a reputed LCD display manufacturer since 1991. It manufactures panels for its own devices and also works as a supplier for several other Big Tech firms, such as Apple. Its displays are used in virtually all products, ranging from foldable smartphones to televisions and tablets.

Despite the company’s successful business, a recent report from The Korea Times suggests Apple is exiting the LCD production business for good. One of the biggest reasons cited for the decision is the increased competition from Chinese and Taiwanese display manufacturers in the recent past.

Samsung wanted to shut its LCD production late in 2020 and its move was on the cards for a while now. Samsung probably kept its LCD manufacturing facilities operational during the pandemic due to the sudden and unprecedented spike in demand. However, LCD technology has been eclipsed by OLED and QD-OLED technologies on most mainstream devices in the last few years. This is another reason why Samsung will probably shutter the business later this year.

Moreover, research firm Display Supply Chain Consultants (DSCC) believes the average price index of LCD panels measured as 100 in January 2014 will drop down to just 36.6 in September 2022. The figure is indicative of the demand for LCD panels and it plummeted to a record low of 41.5 in April this year. The April figure is a whopping 58 percent lower than the record-high index value of 87 in June 2021 when the pandemic was raging. This reduction in demand and price could also be detrimental to the company’s plans to soldier on producing LCDs.

The report says that in the future, Samsung will remain focused on manufacturing OLED panels and more advanced quantum dot OLED displays. LCD division staffers will likely be transferred to the QD-OLED division. Meanwhile, Samsung Display did not respond to the Korea Times’ request for comment.

There are very obvious massive black spots on the surface of the long bar LCD screen, or there are uneven patches of light and dark and cracks at the same time. The liquid crystal display is squeezed or impacted by the external force, resulting in the liquid leakage phenomenon caused by the rupture of the liquid crystal screen. The external force is not too large, although the liquid crystal screen leakage, but there is no crack on the surface, this fault phenomenon is not easy to find, especially in the case of LCD power is not bright. After the liquid crystal display ruptures the leak, the image can still be displayed.

Strip liquid crystal screen leakage is physically damaged, and the liquid crystal screen is cut and manufactured as a whole, once the leakage will slowly expand, or even can not display normally, which is irreparable unless the entire screen is replaced. But in terms of the cost of making liquid crystal displays, the screen accounts for 2/3, so it"s not cost-effective to replace the screen, so it"s better to buy a new monitor.

The control and drive circuit in the bar display module is a low-voltage, micro-power CMOS circuit, which is easy to be breakdown by static electricity. Electrostatic breakdown is a kind of irreparable damage, which must be paid attention to and should not be careless. Therefore, the display screen in the operation, assembly and use should be careful, to strictly prevent static electricity.

It is best to add a gasket of about 0.1 mm between the bar display module and the front panel, and the panel should also be flat to avoid distortion after assembly.

A maintenance film is affixed to the surface of the installed bar display screen to prevent defilement of the appearance during assembly, so it should not be removed before the whole machine is assembled, so as not to stain or damage the appearance surface.

The above is how to maintain the whole content of the bar LCD screens, I hope that we can learn the method of maintenance, so as to prolong the life of the LCD screens. If you want to purchase bar lcd screens, please contact us by email to

Just recently I"ve noticed a very sticky liquid leaking out of one corner of the screen. There are now bright and dark patches on the screen near where it"s leaking. As well as round the screen the sticky stuff gets onto the base of the laptop where I rest my hands to type. lt"s really hard to clean off and I"m worried it may be toxic.

There has been no physical damage to the laptop at all - it just started leaking. Is this a common fault or is it a sign of a defect in the design and manufacture?

Light leak or backlight bleeding is often noticeable around the edges or the sides of a screen. Especially while it is displaying a dark background or is in a dark environment.

Ideally, light leakage must not be inspected in a dark room. All Dell monitors are inspected as per industry standard with 150-Lux ambient lighting (similar to typical office lighting). However, for gaming monitors, ambient lighting is 70 Lux. Any visual inspection must be done in the same manner to help with the troubleshooting process.

NOTE: This article provides information about common issues that are seen on LCD screens. It is not something specific to a particular Dell computer but is something that can be seen on any LCD screen by any manufacturer.

Before proceeding to the troubleshooting section of this article, you must identify the issue that you are experiencing. Identify the light leak or light bleed issue using the examples below and ensure that this is the correct article for you.

LCD display screens on tablets are made of two thin layers of glass with dark liquid crystal material in between. The glass is covered on the outside by a layer of plastic. Customers often feel there cannot be a broken LCD display because they cannot feel the break. However, cracks in the glass usually cannot be felt because the plastic covering rarely breaks or fractures.

It is important to understand that lines on the LCD can also be caused by video driver issues or a problem with the media you are using. Video driver issues can normally be resolved by downloading and installing a new video driver. However, if the damage is due to a broken LCD, you should understand the following policies.

The highest possible sensitivity.If you want to find leaks faster for your customers, try the Fieldpiece DR82 Infrared Refrigerant Leak Detector. Our newest detector can sniff out leaks at <0.03 oz/yr. That’s 20 times more sensitive than soap bubbles. This exceeds detection standards so you can quickly find and pinpoint leaks. DR82 triggers on all HFC, CFC, HCFC, HFO and blends.