diy lcd panel case made in china

Hi everybody! Bill Owen from Mnpctech. I hope you"re having a great day! Several people have asked if I could share the steps on how I do my Touchscreen LCD mod in PC Computer case bezels, and you’ve come to the right video!

I’ve been using this Amazon 5 Inch Capacitive Touch Screens for $52.99 delivered on Amazon Prime, I’ll posted a link in Video description. The kit comes a with Micro USB for power and HDMI video connector, but these cables are too short for these PC case mods. It includes M3 stand-offs, a Driver Disc and some Instructions. It’s a 5 point Capacitive Touch screen with a Resolution of 800 x 460, which is just fine for it’s 5” viewing screen In addition to the LCD touchscreen, I will buy the following cables for my Desktop Custom PC LCD Case Mod.

One 3ft “Right Angle” 270 degree HDMI cord, 6” 90 Degree Angle HDMI Extension Adapter, and 3ft USB Male to Micro B power connector. For Mounting the LCD Touchscreen Panel, I use 3/16” thick Black acrylic to make custom mounting brackets for the LCD touch screen.

You can PAUSE the video on this page to record the measurements that I’ve made for cutting the acrylic. This PC Case Mod is very easy. "The reason I’m making brackets for my desktop PC LCD Monitor Mod?" I want the ability to easily install or remove the Touchscreen with thumbscrews. I’m using 1/8” drill bit for acrylic, and 6/32 thread tap, These Black thumbscrews from Mnpctech.com. I’ll use the 1/8” drill bit to increase the diameter of the holes in the LCD pcb frame.

I discovered these drill bits for plastic several years ago, Notice the bit isn’t splintering or cracking the acrylic as I make the holes. Mnpctech stocks a variety of these drills bits. My mod requires Twelve 6/32 washers, and links posted in description, “Why so many washers?” We want the Touchscreen to mount flush on the backside of the bezel, I also don’t want to apply any unnecessary pressure to the screen or the PCB, See how this sheet of paper easily slides under the screen Next stage is cutting the hole in the bezel, The best PC case for this mod is the ones without optical drive bays, which every popular case manufacturer now offers.

If you’re using an older case with 5.25 drive bays, you could attach a mounting plate with 5” opening that covers THREE 5.25 bays. That’s how we did this mod in the early days of PC Modding. Determine and measure out a location in the center of your bezel, you can also mount the LCD vertically if you prefer, and just change the screen orientation in Windows. Since the bezel is plastic, I’m using a Dremel with 1.5” reinforced cut off wheel, Don’t forget to always wear eye protection when using power tools. Oops, WTH? Hahaha After cutting our 5” diagonal square hole, I’ll hand file the edges so everything is precise and clean. You may have to remove sound insulation foam from backside of your bezel, I’m using E6000 adhesive to attach the two mounting brackets. This adhesive is very GOOEY at first, so consider masking off the screen, to prevent getting any of this on it. I like that it’s tacky for couple of minutes, so I have time to position the LCD in place, and then I’ll temporarily tape it in place while it cures overnight.

Mounting your Touchscreen LCD in the PC this way allows you to easily remove and re-install the LCD at any time. Especially if you ever need to replace it for some reason. Let’s get this LCD touchscreen connected to the PC, all of the cables are routed from the front to thee rear PCI slots. *3ft “Right Angle” 270 degree HDMI cord *6” 90 Degree Angle HDMI Extension Adapter cable, I plug this compact cable into the Touchscreen to save space. *3ft USB Male to Micro B power connector This mod is great if you want an extra screen for monitoring your hardware and temps. You can also display Weather or calendar or email notifications,

Check out http://www.Rainmeter.net this community offers several hundred custom mad graphic interfaces for FREE, and you can configure your screen to display a variety of updated information tasks Thanks for watching! And Again, all of the products used in this PC case mod are listed in the video description.

More ideas below: How To Make DIY display cases design How To Build Wooden DIY display cases Ideas Glass DIY display cases Book Storage Vintage DIY Action Figures display cases Modern DIY Sports display cases Man Caves Hot Wheels DIY display cases Shadow Box DIY Military Business display cases

A while back I was sitting around and wondering what to do with my dead laptop. I knew the mother board was fried but everything else was still in working condition. As a result, I decided to make an external monitor from my dead laptop and proceeded to do the research to find out if this was possible. Below is what I discovered. Unfortunately, there was no way to use the motherboard"s VGA connector. The VGA connector on a laptop is used to connect to an external monitor. In any case the VGA connector is output only and wouldn"t work for an external screen. As a result, I found that I needed to buy a controller board for the LCD screen, to make it work as an external monitor. This was the main cost but was still less than half the cost of buying an external monitor.

Step Two. To Remove the LCD screen from the laptop, you will need to remove the screws. There are rubber pads on the front of the LCD screen to protect it when the laptop lid is closed. Behind the rubber pads are the screws. Find and remove all the screws holding the front plastic frame on the laptop lid. Keep track of the pads and screws as you will need them to reassemble everything.

Step Three. Remove the plastic frame from the LCD screen. Here is where you need to be careful. The screws are not the only thing holding the plastic frame on the LCD screen! The plastic frame is snapped into place. Carefully pry loose the frame from the LCD screen. Pry it loose gently. Try to keep it as close as possible to the LCD panel while you are prying it loose because you may also find that you need to slide it to the left or right to completely remove it from the laptop. There is a small protrusion of the plastic frame where the hinge is. Because of this protrusion you need to slide the frame, in this case, to the right, to detach it from the laptop.

Step Four. Locate and remove the screws holding the LCD panel to the laptop. These are located on the bottom. The screws are attached to a small metal hinge. this is the component that is attached to the keyboard frame.

Next you will need to remove the LCD screen. Note that there is a cable attached. This is the LVDS cable. It is best to take apart the rest of the laptop and unplug it from the keyboard. However, the cable can be cut at the bottom. Take care not to cut the two wires going into the inverter (that"s the slim circuit board at the bottom.

Once the LCD panel is removed, you can remove the LVDS cable and unplug the inverter at the bottom. Unplug the inverter from both ends. Do not cut it. The LVDS cable is taped to the back of the LCD screen at the top. It is the flat cable running up the back. Remove the tape and slid the cable down. Since you need to buy an LCD controller board, you will no longer need the LVDS cable the laptop came with or the inverter. At this point you should just have an LCD screen with a pair of wires coming out of it.

Keep track of the plastic front frame and the plastic backing. You will need them to resemble the LCD screen. On the other hand, you have different fingers, just kidding. On the other hand, you can buy a picture frame and put the LCD screen in the picture frame.

Here is a picture of the LVDS cable and the inverter detached from the LCD screen. Since we will be buying an LCD control board these cables will not be needed again.

Next, once you have removed the LCD panel. Flip it over and look for a model number on the back. You will need this model number to order the correct LCD controller board. I went to E-Bay and found one for $42.00. I bought the LCD controller board and then received an email from the seller requesting the model number of the LCD screen and manufacturer. This is because each controller board is flashed, (programed to run a specific LCD) I gave him my model number, LP171WX2 A4K1 and told him it was made by LG Phillips. Since the board was coming from China, I received my order about 2 weeks later. Due note to buy one with a power cord! The LCD controller board has the VGA input connection which allows you to connect it to another computer and use it as a second monitor or as a back up in the event the one on your working computer goes out.

The LCD controller board is real easy to connect. It comes with all the required cables, except a VGA cable which you will need, in order to connect your LCD to another computer. You can buy a VGA cable from Best Buy or a computer parts store.

The LCD control Bard comes with all the cables except the VGA cable which you will have to buy. Once you have received your kit, proceed to connect it to the LCD screen. Plug the LVDS cable into the LCD panel where you removed the original from. The two wires at the bottom of the LCD screen that were connected to the inverter need to be unplugged from the old inverter and plugged into the new inverter below. Then, plug the power in. Make sure that the LCD control board is not sitting on anything conductive, like metal or it will short and fry. Next connect the VGA cable to the LCD control board and plug the other end of the VGA cable to another computer. Make sure the computer is on before you plug in the VGA cable. At this point you should have the same image that is on the computer you plugged the VGA cable into, on the LCD panel.

Next, I attached a 4 inch section of two by four on the outside back of the laptop lid. I needed this in order to attach my stand to the LCD screen. I used 5 screws and screwed them in place from the inside. I did splice and extend the cables going from the LCD controller to the inverter it came with just to have a little more room.

Originally, I built a nice wooden stand for my LCD panel but was not satisfied with it. So, I took a broken florescent desk lamp and dremeled off the section holding the florescent tubes, leaving enough metal to screw on to the two by four on the laptop lid. Before attaching the stand, I drilled four holes in the metal to make it easier to screw it on the two by four.

Next you will need to attach the LCD controller to the laptop lid. To do this, screw in a few sections of wood from the inside of the lid. Then on the outside of the lid attach the LCD control board. Place the wood in an area where the control board can reach.

Next you will need to find all those screws you have been saving and reassemble the LCD screen. I also added some surgical tubing to the top springs for added strength.

By the way a store bought swing arm half the size of this one, I found, cost around $400.00. If you choose to use a swing arm like this one, go with the one that has a magnifier on it and dremel off the magnifier leaving enough metal to attach to your LCD lid. You need one of this caliber to hold the LCD screen. Swing arms with the light attached are not strong enough.

Since I was asked about the web cam, I though Should add it to the instructable. There is a nice instructable here at this site showing how to convert a web cam from an LCD screen: http://rntmns.com/2011/02/rebirth-of-a-webcam/

Actually, you can do One better. You can salvage the RAM, the Wireless card, the Batteries, the charger, the hard drive, the DVD disk player and sell them to people that need them on E-bay and Still keep the LCD screen for yourself.

The LVDS cable of the controller board is too short for the way I need it to be, does anyone know if there is an easy or inexpensive way to extend its lenght? (with LVDS cable I mean the 20/30 pin cable that is the main data cable for the display and goes to [in my case] 20 pin on the big board of the controller board)

I checked ebay for the LCD control Board and all I did was punch in " LCD control Board for a LP154W01(A3)" , That"s my model number. You, of course, use your"s. ebay came up with the correct one for $25.00 and it has all the imputs you could want. This is good today, 2/11/19. Have fun folks!

i have a similar lcd panel to yours. infact 3 of them! they"re so easy to work with and doesn"t need a backlight controller LP154WH4 TLA1 except the lvds cable sold separately. I"ve build one and runs on

Nicely done and very informative!! However unfortunately, by the time you add the cost of the LCD Controller card, various parts and time you could have bought a new inexpensive monitor.

it really depends on what kind of display your laptop came with. I recently had a laptop that featured a 4k OLED screen and If I add the price up of the controller kit and materials (depending how you are going to make the stand) it would actually in my case be cheaper to make that an external monitor because, quite frankly 4k is pretty expensive and I don"t want to degrade to a lower resolution. in said laptop the motherboard died so I just scavenged everything including the LCD which I have just lying on my desk. so I might even consider trying this.0

If you want to display items at your shops in the most impressive way, Alibaba.com can help you do that with the sturdy and trendy diy transparent display collections. These stylish and freestanding diy transparent display are ideal for displaying all types of products at your space in a fabulous way. The quality of these diy transparent display is very rigid and made of superior raw materials to ensure long-lasting performance and stability. These products are easy to assemble and can be maneuvered with ease from one place to the other.

The unique and robust diy transparent display offered on the site are not just tough in terms of quality but are also very appealing aesthetically and spacious enough to display plenty of items in one single place. These diy transparent display are very easy when it comes to installation and are equipped with compression loads feature that let them withstand any weight you put. You can also customize the shelves as well as hooks of the diy transparent display as per your needs and are multi-usage.

Alibaba.com offers an exciting range of diy transparent display according to their sizes, shapes, shelves, designs, and colors to let you choose as per your requirements. These diy transparent display are made from all types of sturdy materials such as stainless steel, white acrylic and hardware, metal wire, wood, cardboard, and many more. The diy transparent display come with powder-coated surface treatments and can be completely customized in terms of designs.

Check out the varied diy transparent display ranges at Alibaba.com and go for the products that meet your finances and requirements. These items are offered as OEM products on bulk orders and you can enjoy brilliant deals at regular intervals. Customized packaging is also available along with free shipping.

There are more and more TFT displays used in outdoor applications, such as automobile display, digital signage and kiosks. High ambient light in outdoor environment often causes wash-out image and renders the screen not readable. Readability & sustainability of TFT  display under direct sunlight is becoming vital. Topway Display has been developing sunlight readable LCD display solution for years. The company understands the ins and outs of sunlight readable TFT LCD.

For an LCD to be readable in outdoor environment with very bright ambient light, the LCD screen’s brightness needs to exceed the intensity of light that is reflected from the display surface. To be comfortably viewed by human eyes, the LCD’s brightness needs to exceed its reflected light by a factor of 2.5 at minimum. Naturally, to make an LCD sunlight readable, we can work on two areas, increasing brightness or reducing reflectance.

On a clear day in direct sunlight, the ambient brightness is about 6000 cd/m2. And a typical TFT LCD with touch screen reflects about 14% of ambient light, which is around 840 cd/m2. These days, most LCD displays use LED backlight as light source. It is not too difficult to increase an LCD’s brightness to 800 ~ 1000 Nits, to overpower the bright reflected sunlight. Thus, you have a sunlight readable TFT LCD.

However, this method requires more backlight LEDs and/or higher driving current. The drawbacks are high power consumption, more heat dissipation, increased product size and shorter LED backlight lifespan. Apparently, increasing backlight to make TFT LCD sunlight-readable is not a very good solution.

Transflective TFT LCD is a TFT LCD with both transmissive and reflective characteristics. A partially reflective mirror layer is added between LCD and backlight. This change turns part of the reflected ambient light into LCD’s light source, increasing the TFT display’s brightness. However, transflective TFT LCD is more expensive than transmissive one. At the same time, the partially reflective mirror layer will block some of the backlight, making it not ideal in indoor or low ambient light environment.

The total reflectance on a TFT LCD with touch panel is the sum of reflected light on any interface where two materials meet. As an example, between polarizer and display glass, the difference in index of refractions for the two materials is very small, around 0.1. So the reflected light on this interface is only 0.1%. As Fresnel’s equation points out, we should focus reflection reduction on air interfaces. For air, its index of refraction is 1; for glass, it is 1.5. And that results in a reflectance of 4.5%. Therefore, the three air interfaces contribute majority of TFT LCD’s reflectance, at about 13%.

For food industry application, shattered glass is a serious problem. An LCD screen with external film solves this issue nicely. As for automotive applications, in an accident, broken LCD with top AR film won’t produce sharp edge glass that could harms auto occupant. Nevertheless, a top film always reduces TFT LCD’s surface hardness. And it is susceptible to scratches. On the other hand, AR coating retains LCD’s hardness and touch performance. But it comes with a bigger price tag.

Another quick and easy way to tackle reflectance is to affix a linear polarizer on the top of TFT screen. When ambient light gets to the top polarizer, only half of the light passes through. Which results in reflection light cutting to half. This is a very low cost way to increase TFT LCD’s contrast, such that making it more sunlight readable.

Laminating a circular polarizer in TFT LCD will get rid of a lot of reflectance. That is because when ambient light passes through circular polarizer it gets circularly polarized. And when it is reflected, the polarization direction flips by 180 degrees. So when reflected light comes back to the circular polarizer, nothing goes through to viewer’s eyes.

This method is very effective for an LCD display with resistive touch panel. We know resistive touch LCD has two air gaps: air gap between two ITO layers and air gap between touch panel and LCD display. Reflectance caused by the two air gaps is very high. Applying circular polarizer blocks off most of the reflected light, and makes the LCD display sunlight readable.

The disadvantage of such solution is its cost. Since we need not only a circular polarizer, but also a retarder film on the top of LCD display, making sure light originates from within LCD is not blocked by external circular polarizer.

Add AR films on both interfaces of internal air gap. The add-ons can reduce this area’s reflection from 8.5% to 2%. And since the AR films are not outside facing, they are much cheaper than the one used outside. Keeping the air gap also retains the ease of service, in case either touch panel or LCD display needs to be repaired.

The most effective way is to eliminate air gap totally, by using optical bonding. In plain language, we fill air gap with special optical adhesive, to smooth out the area’s refraction index differences. Such that reflectance caused by internal air gap drops from 8.5% to 0.5%. Optical bonding is expensive but effective way to improve TFT LCD sunlight readability. It enhances durability and resistance to impact. Moreover, no air gap means no moisture condensation and fogging.

There are many ways to make TFT LCDsunlight readable. They all have their own pros and cons. With 20+ years" LCD design and manufacturing experience, Topway knows how to create the best sunlight readable TFT LCD for challenging environments. Leave us a message and let"s start the conversation of creating suitable sunlight readable TFT LCD for your project.

I saw a really cool video of a PC case called “Snowblind“, that had a transparent LCD Screen as a side panel. I was amazed over how cool it was. The only problem was that it was really expensive. Therefore, I tried making my own! In this instructables I will go through how I made it, and how you could make your own. The best of all, since it was made from an old monitor that was thrown away, it was basically free! I just added some LED strips on the inside of the case to get better contrast on the screen. You could probably re-use the monitors backlight, but it’s safer and easier to just get some cheap LED strips.