tft lcd white screen 2.4 manufacturer

The other day I finally found a code that worked on my standard 2.8" TFT LCD by Simkeim, but then I pressed the bottom left corner too hard and the screen went white. The code is a calculator code and it worked because the screen showed the numbers and the screen saver, but when I pressed the screen nothing happened. After the screen went white, I "opened" it and saw no damage to the screen. I have tried a bunch of example sketches and now the touch functions work, but nothing is displayed on the screen. The LCD does not have any wires, it just plugs in the board. When I upload a sketch, the backlight changes brightness a bit, and there is a slight line on the left side of the screen, when the code uses dark colors, I can press two parts of the screen and the screen goes dark (except for a small part of the left side).

No changes made, powered up on the third day, and nothing but a white screen on the ILI9341? So i say, must have blew the t4 some how. Hot air removed the t4, on goes the new one and again a few runs later and i get a white screen again? Checked all my pin assignments, voltages and they are all good.

I picked up the project again today and de-soldered my SAMD51 T4 clone pcb as I need speed! The T4 would have been perfect, so tried a few code changes, got the screen running in the setup function (static text etc), but as soon as it enters the loop(), you guessed it....white screen. Its as if the t4 is too fast on spi or something, but I have changed the clock speeds down to 5mhz and yield the same results...

This graphic display module is a 2.4" diagonal, full color TFT. Suitable for embedded applications, it is low-power, uses a white LED backlight, and has an integrated touch panel which has its connection brought out to the main TAB connector for the display.

LTK0231T4002BL-V0 is a color active matrix thin film transistor (TFT) liquid crystal display (LCD) that uses amorphous silicon TFT as a switching device.

This is our 2.4 inch TFT LCD Display forArduino Uno that will spice up your Arduino project with a touchscreen display shield with built in microSD connection. This TFT display is 2.4″ diagonal with 4 white-LED backlight and 240×320 pixels. It has way more resolution than a black and white 128×64 display. As a bonus, this display has a resistive touchscreen attached to it already, so you can detect finger presses anywhere on the screen.

Winstar WF24H is a 2.4 inch diagonal full color 240x320 TFT display module. This 2.4 inch TFT LCD display is built in with ILI9341V IC; it supports 8/16-bit 8080-series Parallel MCU Interface. WF24H model is having module dimension of 42.72 x 60.26 mm and Active area size of 36.72 x 48.96 mm; it integrated ILI9341V controller on module, logic supply voltage range from 2.4V to 3.3V.

This 2.4" TFT LCD module is portrait mode, if you would like to use landscape mode please contact with us for more technical support. This 2.4" TFT Display is featured with brightness up to 500 cd/m2(typical value), it can be operating at temperatures from -20℃ to +70℃; its storage temperatures range from -30℃ to +80℃. It is very suitable for smart home applications, medical devices, portable devices, wearable devices, energy controls, telecoms and data transfers etc.

Search keyword: tft 2.4, tft 2.4", 2.4 tft lcd, 2.4" tft lcd, 2.4 inch tft lcd, tft lcd 2.4, 2.4 tft display, 2.4" tft display, 2.4 inch tft display, tft display 2.4, tft display 2.4"

Available in a variety of sizes, premium MVA (Multi-domain Vertical Alignment) TFT LCDs offer wide viewing angles, fast responses, and excellent color reproductions and depths.

The game will compile and work, I can see it working on the serial monitor.  The issue is the screen stay white.  I can load examples codes and the display screen works perfectly.