1.44 tft lcd module arduino in stock

ER-TFTM1.44-2 is 128x128 pixel 1.44 inch color tft lcd display panel with ST7735S controller and breakout board,superior display quality,wide viewing angle,super and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO,ARM and Raspberry PI.It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.It"s 4-wire serial spi interface with pin header connection.It"s easily controlled by MCU such as 8051,PIC,AVR,ARDUINO,ARM and Raspberry Pi.It can be used in any embedded systems,industrial device,security,medical and hand-held device.

Features:100% brand new and high quality This 1.44-inch LCD module uses ST7735 drive chip to drive 128x128 dot, with 128 x 128 resolution 1.44-inch screen with SPI serial module, a minimum of only four IO-driven resolution 128 * 128 Perfect upgrade true color, replace the black and white LCD screen for nokia 5110/3310 This TFT LCD Display Module comes With PCB plate

» Makerfabs is Open Hardware, Arduino, Raspberry Pi, mbed, BeagleBone, IoT, Smart Home, etc, Related Products& Services Vendor for Makers and new Startups.

The 1.44" display has 128x128 color pixels. It is the best way to add a small, colorful, and bright display to any project. Since the display uses 4-wire SPI to communicate and has its own pixel-addressable frame buffer, it can be used with every kind of microcontroller. Even a very small one with low memory and few pins available!

This 1.44 inches TFT LCD from Elecrow has a 128 x 128 resolution display that uses SPI communication to interface with microcontrollers like Arduino. You can use it to upgrade a Nokia 5110 phone as it originally sports a monochromatic display while this display supports 262 varieties of color! Otherwise, it is the perfect portable display for your embedded projects.

1.44 inch Oled Arduino TFT LCD ModuleIt has full color feature. It is compatible with Arduino. It can be controlled correctly. The screen provides color levels, good brightness and high contrast.

A number of display devices like LEDs, 7-segments, character and graphic displays can be attached to microcontrollers to create an interface between the user and an electronic system for displaying data or controlling the system. Sometimes you may need to add colorful images or graphics to your project, that’s where the TFT color displays come in handy.

TFT LCD is a variant of a liquid-crystal display (LCD) that uses thin-film-transistor (TFT) technology to improve image qualities such as addressability and contrast. In this tutorial we are going to show how to interface a 1.44″ TFT color display based on the ST7735 driver. It has 128×128 color pixels and can display full 16-bit color.

This is the type of display am using but they come with various pin configurations. However all the displays will have the major pins stated below and should be connected to the Arduino board as follows:

This TFT display uses 3.3V but comes with an on board voltage regulator therefore the VCC can be connected to the Arduino 5V. However for best practice it’s better to use the 3.3V.

Most code Libraries for this TFT ST7735 display with Arduino are programmed with the SDA and SCL pins connected to Arduino pins 11 and 13 respectively. Make sure you don’t change that order otherwise the display may not work.

There are a number of libraries that have been developed to run the TFT ST7735 color display using Arduino but I found the Adafruit-ST7735-Librarythe best to use. Make sure you have this library installed in your IDE.

tft.fillRoundRect(x,y,w,h,r,t); function draws a filled Rectangle with r radius round corners in x and y location and w width and h height and t color.

There are many other functions and commands which you can use to program the TFT color display but the above are the commonest. You will meet many more with practice.

We"ve written a full open source graphics library that can draw pixels, lines, rectangles, circles, text and bitmaps as well as example code and a wiring tutorial . The code is written for Arduino.

Note:If you want to show the whole pitcure on the screen, it"s suggest using arduino mega2560. Because when you use Arduino UNO, thememory is not enough which cause the application simply ran out of memory.

The breakout has the TFT display soldered on (it uses a delicate flex-circuit connector) as well as a ultra-low-dropout 3.3V regulator and a 3/5V level shifter so that you can use it with 3.3V or 5V power and TTL control logic.

This lovely little display breakout is the best way to add a small, colorful and bright display on to your project. Since the display size is 1.44-inch and since TFT display has its own pixel-addressable frame buffer, it can be used with every kind of microcontroller. Even a very small one with low memory and few pins available!

In the above example, Node32-Lite and this 1.44-inch LCD.  Please refer to the tutorial here: ST7735S interfacing with ESP32 to make the connections, Arduino library installation, and modification needed for it to works on this LCD.