crt tft lcd led oled and amoled free sample

In market, LCD means passive matrix LCDs which increase TN (Twisted Nematic), STN (Super Twisted Nematic), or FSTN (Film Compensated STN) LCD Displays. It is a kind of earliest and lowest cost display technology.

LCD screens are still found in the market of low cost watches, calculators, clocks, utility meters etc. because of its advantages of low cost, fast response time (speed), wide temperature range,  low power consumption, sunlight readable with transflective or reflective polarizers etc.  Most of them are monochrome LCD display and belong to passive-matrix LCDs.

TFT LCDs have capacitors and transistors. These are the two elements that play a key part in ensuring that the TFT display monitor functions by using a very small amount of energy without running out of operation.

Normally, we say TFT LCD panels or TFT screens, we mean they are TN (Twisted Nematic) Type TFT displays or TN panels, or TN screen technology. TFT is active-matrix LCDs, it is a kind of LCD technologies.

TFT has wider viewing angles, better contrast ratio than TN displays. TFT display technologies have been widely used for computer monitors, laptops, medical monitors, industrial monitors, ATM, point of sales etc.

Actually, IPS technology is a kind of TFT display with thin film transistors for individual pixels. But IPS displays have superior high contrast, wide viewing angle, color reproduction, image quality etc. IPS screens have been found in high-end applications, like Apple iPhones, iPads, Samsung mobile phones, more expensive LCD monitors etc.

Both TFT LCD displays and IPS LCD displays are active matrix displays, neither of them can produce color, there is a layer of RGB (red, green, blue) color filter in each LCD pixels to make LCD showing colors. If you use a magnifier to see your monitor, you will see RGB color. With switch on/off and different level of brightness RGB, we can get many colors.

Neither of them can’t release color themselves, they have relied on extra light source in order to display. LED backlights are usually be together with them in the display modules as the light sources. Besides, both TFT screens and IPS screens are transmissive, it will need more power or more expensive than passive matrix LCD screens to be seen under sunlight.  IPS screens transmittance is lower than TFT screens, more power is needed for IPS LCD display.

Steven Van Slyke and Ching Wan Tang pioneered the organic OLED at Eastman Kodak in 1979. The first OLED product was a display for a car stereo, commercialized by Pioneer in 1997. Kodak’s EasyShare LS633 digital camera, introduced in 2003, was the first consumer electronic product incorporating a full-color OLED display. The first television featuring an OLED display, produced by Sony, entered the market in 2008. Today, Samsung uses OLEDs in all of its smartphones, and LG manufactures large OLED screens for premium TVs. Other companies currently incorporating OLED technology include Apple, Google, Facebook, Motorola, Sony, HP, Panasonic, Konica, Lenovo, Huawei, BOE, Philips and Osram. The OLED display market is expected to grow to $57 billion in 2026.

AMOLED (Active Matrix Organic Light Emitting Diode) is a type of OLED display device technology. OLED is a type of display technology in which organic material compounds form the electroluminescent material, and active matrix is the technology behind the addressing of individual pixels.

An AMOLED display consists of an active matrix of OLED pixels generating light (luminescence) upon electrical activation that have been deposited or integrated onto a thin-film transistor (TFT) array, which functions as a series of switches to control the current flowing to each individual pixel.

Typically, this continuous current flow is controlled by at least two TFTs at each pixel (to trigger the luminescence), with one TFT to start and stop the charging of a storage capacitor and the second to provide a voltage source at the level needed to create a constant current to the pixel, thereby eliminating the need for the very high currents required for PMOLED.

TFT backplane technology is crucial in the fabrication of AMOLED displays. In AMOLEDs, the two primary TFT backplane technologies, polycrystalline silicon (poly-Si) and amorphous silicon (a-Si), are currently used offering the potential for directly fabricating the active-matrix backplanes at low temperatures (below 150 °C) onto flexible plastic substrates for producing flexible AMOLED displays. Brightness of AMOLED is determined by the strength of the electron current. The colors are controlled by the red, green and blue light emitting diodes.  It is easier to understand by thinking of each pixel is independently colored, mini-LED.

IPS technology is like an improvement on the traditional TFT LCD display module in the sense that it has the same basic structure, but with more enhanced features and more widespread usability compared with the older generation of TN type TFT screen (normally used for low-cost computer monitors). Actually, it is called super TFT.  IPS LCD display consists of the following high-end features. It has much wider viewing angles, more consistent, better color in all viewing directions, it has higher contrast, faster response time. But IPS screens are not perfect as their higher manufacturing cost compared with TN TFT LCD.

Utilizing an electrical charge that causes the liquid crystal material to change their molecular structure allowing various wavelengths of backlight to “pass-through”. The active matrix of the TFT display is in constant flux and changes or refreshes rapidly depending upon the incoming signal from the control device.

"Between 0.0001 and 0.00001 nits" "Sony claims an OLED contrast range of 1,000,000:1. When I asked how the contrast could be so high I was told that the surface is SO black the contrast is almost infinite. If the number representing the dark end of the contrast scale is nearly zero then dividing that number into the brightest value results in a very, very high contrast ratio."

Does not normally occur at 100% brightness level. At levels below 100% flicker often occurs with frequencies between 60 and 255 Hz, since often pulse-width modulation is used to dim OLED screens.

No native resolution. Currently, the only display technology capable of multi-syncing (displaying different resolutions and refresh rates without the need for scaling).Display lag is extremely low due to its nature, which does not have the ability to store image data before output, unlike LCDs, plasma displays and OLED displays.

What are the key differences between leading electronic visual displays available in the market? Such are the times that we live in that today most of us cannot possibly imagine a life without an electronic device. In fact, we have managed to surround ourselves and depend on a growing number of electronic appliances. Several of these devices - as it happens - also have an electronic visual display; be it a mobile phone, a tablet, a desktop monitor or the television set. Without a doubt, these electronic screen devices have revolutionised the way we lead our lives now as all of the four devices have become increasingly commonplace to the point of becoming basic necessities. Which brings to our blog topic: what exactly is an electronic screen and which are the leading screen technologies available today? Read on to know more…

An electronic screen or an electronic visual display, informally called a screen, is basically a device used to display / present images, text, or video transmitted electronically, without creating a permanent record. As mentioned earlier, electronic visual displays include television sets, computer monitors, and digital signage in information appliances. As per the definition, an overhead projector (along with screen onto which the text, images, or video is projected) can also be called an electronic visual display.

1. Cathode Ray Tube (CRT) display:A vacuum tube containing one or more electron guns and a phosphorescent screen, the cathode-ray tube (CRT) is used to display images. It modulates, accelerates, and deflects electron beams onto the screen to make the images. The images could be electrical waveforms (oscilloscope), pictures (television, computer monitor) or radar targets. CRTs have also been used as memory devices, wherein the visible light from the fluorescent material (if any) does not really have any significant meaning to a visual observer, but the visible pattern on the tube face could cryptically represent the stored data. In television sets and computer monitors, the front area of the tube is scanned systematically and repetitively in a pattern called a raster. Thanks to the intensity of each of the three electron beams - one for each additive primary color (red, green, and blue) - being controlled with a video signal as a reference, an image is produced. In modern CRT monitors and TVs, magnetic deflection bends the beams; magnetic deflection is essentially a varying magnetic field generated by coils and driven by electronic circuits around the neck of the tube, although electrostatic deflection is often used in oscilloscopes, a type of electronic test instrument. CRT is one of the older screen/ display technologies.

2. Flat-Panel display: Flat-panel displays are electronic viewing technologies that are used to allow people to see content (still images, moving images, text, or other visual material) in a range of entertainment, consumer electronics, personal computer, and mobile devices, and several kinds of medical, transportation and industrial equipment. They are much lighter and thinner than traditional cathode ray tube (CRT) television sets and video displays and are typically less than 10 centimetres (3.9 in) thick. Flat-panel displays can be classified under two display device categories: volatile and static. Volatile displays need pixels to be periodically electronically refreshed to retain their state (say, liquid-crystal displays). A volatile display only shows an image when it has battery or AC mains power. Static flat-panel displays rely on materials whose color states are bistable (say, e-book reader tablets from Sony), and they retain the text or images on the screen even when the power is off. In recent times, flat-panel displays have almost completely replaced old CRT displays. Most flat-panel displays from the 2010s use LCD and/or LED technologies. Majority of the LCD screens are back-lit as color filters are used to display colors. Being thin and lightweight, flat-panel displays offer better linearity and have higher resolution than the average consumer-grade TV from the earlier decades. The highest resolution for consumer-grade CRT TVs was 1080i, whereas many flat-panels can display 1080p or even 4K resolution.

3. Plasma (P) display: A plasma display panel (PDP) is a type of flat panel display that uses small cells containing plasma; ionized gas that responds to electric fields. Earlier, plasma displays were commonly used in larger televisions (30 inches and larger). But since more than a decade now, they have lost almost all market share due to competition from low-cost LCDs and more expensive but high-contrast OLED flat-panel displays. Companies stopped manufacturing plasma displays for the United States retail market in 2014, and for the Chinese market in 2016.

4. Electroluminescent display (ELD):Electroluminescent Displays (ELDs) are screens that make use of electroluminescence. Electroluminescence (EL) is an optical and electrical phenomenon where a material emits light in response to an electric current passed through it, or to a strong electric field.

So ELD then is a kind of flat panel display produced by sandwiching a layer of electroluminescent material between two layers of conductors. When the current flows, the layer of material emits radiation in the form of visible light. Basically, electroluminescence works by exciting atoms by passing an electric current through them, leading them to emit photons. By varying the material being excited, the color of the light being emitted is changed. The actual ELD is built using flat, opaque electrode strips running parallel to each other, covered by a layer of electroluminescent material, followed by another layer of electrodes, running perpendicular to the bottom layer. This top layer has to be transparent so as to allow light to escape. At each intersection, the material lights, creating a pixel.

5. Liquid Crystal Display (LCD): A liquid-crystal display (LCD) is a flat-panel display or other electronically modulated optical device that makes use of the light-modulating properties of liquid crystals. Liquid crystals do not give out light directly; they use a backlight or reflector to create images in color or monochrome. LCDs display arbitrary images like in a general-purpose computer display or fixed images with low information content, that can be displayed or hidden, such as preset words, digits, and seven-segment displays, like in a digital clock. They use the same core technology, apart from the fact that arbitrary images are made up of a large number of small pixels, while other displays have larger elements. LCDs could be on (positive) or off (negative), as per the polarizer arrangement. For instance, a character positive LCD with a backlight has black lettering on a background the same color as the backlight, and a character negative LCD has a black background with the letters matching the backlight color. Blue LCDs typically get their characteristic appearance from optical filters being added to white.

LCD screens are being used in several applications such as LCD televisions, computer monitors, instrument panels, aircraft cockpit displays, and indoor and outdoor signage. Small LCD screens are seen in portable consumer devices such as digital cameras, watches, calculators and mobile telephones, including smartphones. LCDs are also found in consumer electronics products such as DVD players, video game devices and clocks. It is interesting to note that these displays are available in a wide range of screen sizes as compared to CRT and plasma displays. Also, while LCD screens have replaced heavy, bulky cathode ray tube (CRT) displays in almost all applications, they are slowly being replaced by OLEDs, which can be easily made into different shapes, and boast other advantages such as having a lower response time, wider color gamut, virtually infinite color contrast and viewing angles, lower weight for a given display size and a slimmer profile and potentially lower power consumption. OLEDs, however, are more expensive for a given display size and they can suffer from screen burn-in when a static image is displayed on a screen for a long time (for instance, the table frame for an airline flight schedule on an indoor sign), not to mention that there is currently no way to recycle OLED displays. LCD panels, on the other hand, are susceptible to image persistence but they rarely suffer image burn-in as they do not use phosphors, plus they can be recycled, although this technology is not exactly common as yet. Not surprisingly, attempts have been made to increase the lifespan of LCDs in the form of quantum dot displays, which provide performance to that of an OLED display, but the Quantum dot sheet that gives these displays their characteristics can not yet be recycled. LCDs are also more energy-efficient and can be disposed of more safely than a CRT display.

6. Light-Emitting Diode (LED) display:An LED display is a flat panel display that uses an array of light-emitting diodes as pixels for a video display. Their brightness lets them be used outdoors where they are visible in the sun for store signs and billboards. It was in 1962 that LED diodes first came into being; this was when the first practical LED was invented by General Electric’s Nick Holonyak Jr. This was also when they were mainly red in color. While the early models had a monochromatic design, the efficient Blue LED completing the color triad became available in the market only in the late 1980s. Today, large displays use high-brightness diodes to generate a wide spectrum of colors. In fact, recently, LEDs have also become a popular choice among destination signs on public transport vehicles and variable-message signs on highways. LED displays can offer general illumination in addition to visual display, as when used for stage lighting or other decorative (as opposed to informational) purposes. Several big corporations such as Apple, Samsung and LG are currently looking to develop MicroLED displays. These displays are easily scalable, and help with making the production process more streamlined. That said, production costs continue to be quite high and thus remain a limiting factor.

7. Organic Light-Emitting Diode OLED display: An organic light-emitting diode (OLED), also called an organic EL (organic electroluminescent) diode, is a light-emitting diode (LED), where the emissive electroluminescent layer is a film of organic compound that gives out light in response to an electric current. The organic layer is located between two electrodes, at least one of which is transparent. OLEDs are used to build digital displays in devices such as television screens, computer monitors, portable systems such as smartphones, handheld game consoles and digital assistants. Typically, an OLED display works without a backlight because it emits visible light. This means that it can display deep black levels and can be thinner and lighter than a liquid crystal display (LCD). In low ambient light conditions, say in a dark room, an OLED screen can achieve a higher contrast ratio than an LCD, irrespective of whether the LCD uses an LED backlight or cold cathode fluorescent lamps.

Also important to note an OLED display can be driven with a passive-matrix (PMOLED) or active-matrix (AMOLED) control scheme. In the former, each row (and line) in the display is controlled sequentially, one by one, as opposed to in the AMOLED where a thin-film transistor backplane is used to directly control and switch each individual pixel on or off, thus offering higher resolution and larger display sizes.

Lastly, there are two main families of OLED: those based on small molecules and those making use of polymers. A big area of research is the development of white OLED devices for use in solid-state lighting applications.

8. Active-Matrix Organic Light-Emitting Diode (AMOLED) display: AMOLED (Active-Matrix Organic Light-Emitting Diode) is a display device technology being used in smartwatches, mobile devices, laptops, televisions, media players and digital cameras. As mentioned earlier, it is a type of OLED; rather a specific type of thin-film-display technology where organic compounds form the electroluminescent material. What distinguishes it from PMOLED is the active matrix technology behind the addressing of pixels. An AMOLED display basically comprises an active matrix of OLED pixels generating light (luminescence) upon electrical activation that have been positioned or integrated onto a thin-film transistor (TFT) array, which in turn operates as a series of switches to control the current flowing to each individual pixel. AMOLED technology has continued to work towards consuming low power, becoming low-cost and offering scalability (mainly by offering larger sizes.

9. Super AMOLED display: Super AMOLED is essentially an AMOLED display but it is a term coined for marketing purposes by leading device manufacturers. It is used to denote AMOLED displays that come with an integrated digitizer, i.e. the layer that detects touch is integrated into the screen, instead of overlaid on top of it. The display technology however is not an improvement on the AMOLED. For instance, Samsung claims that Super AMOLED displays reflect one-fifth as much sunlight as the first generation AMOLED. In fact, Super AMOLED displays that are part of the Pentile matrix family, are also at times known as SAMOLED. Other variations of this term include Super AMOLED Advanced, Super AMOLED Plus, HD Super AMOLED, HD Super AMOLED Plus and Full HD Super AMOLED.

10. Quantum Dot (QD) display:A quantum dot display is a display device that uses quantum dots (QD), basically semiconductor nanocrystals that can generate pure monochromatic red, green, and blue light. Photo-emissive quantum dot particles are used in a QD layer which converts the backlight to give out pure basic colors that in turn enhance display brightness and color gamut by decreasing light loss and color crosstalk in RGB color filters. This technology is used in LED-backlit LCDs, though it applies to other display technologies as well (such as white or blue/UV OLED).

Among devices employing QD screens, one can find electro-emissive or electroluminescent quantum dot displays, which are currently an experimental type of display based on quantum-dot light-emitting diodes (QD-LED). These displays are similar to active-matrix organic light-emitting diode (AMOLED) and MicroLED displays, as in light is produced directly in each pixel by applying an electric current to inorganic nano-particles. QD-LED displays are supposed to support large, flexible displays and not degrade as readily as OLEDs, making them good bets for flat-panel TV screens, digital cameras, mobile phones and handheld game consoles. As of 2018, all commercial products like LCD TVs that use quantum dots and are called QLED, use photo-emissive particles, whereas electro-emissive QD-LED TVs are only to be found in laboratories today.

This website is using a security service to protect itself from online attacks. The action you just performed triggered the security solution. There are several actions that could trigger this block including submitting a certain word or phrase, a SQL command or malformed data.

We all are familiar with the computer monitors. We spend time sitting in front of them for hours working, gaming or watching movies. A monitor is used to display the output of any computer system. A good display makes all the difference and no doubt enhances the user experience. The innovation in the display technologies has improved the quality of the display devices including monitors. Now the desktop computers are available with a variety of displays ranging from technologically obsolete CRT monitors to latest slim LCD, LED or OLED monitors.

A computer monitor, technically termed as visual display unit is an output device that presents the information from the CPU on the screen working as an interface between CPU and the user. A cable connects the monitor to a video adaptor or video card which is set up on the motherboard of the computer. The CPU (Central Processing Unit) sends instruction to the video adaptor telling what needs to be displayed on the screen. The video adaptor converts the instructions into a set of corresponding signals and sends to the monitor. Monitor contains a circuitry that generates the picture on the screen from the set of signals.

The major parameters that measure the performance of a monitor are luminance, contrast ratio, resolution, dot pitch, response time, refresh rate and power consumption. The common problem that arises in monitors is dead pixels, blurred screen, phosphor-burn, etc.

which were the boxy Video Display Terminals (VDTs). VDTs were monochrome monitors which used CRT (Cathode Ray Tube) technology. They were capable of working with any type of computer by connecting through a serial interface.

IBM’s CRT– IBM launched its first computer also known as a ‘three piece computer’ in 1981. It had three different units – CPU, monitor and keyboard separately. By 1984, IBM introduced the new CRT monitor with enhanced Color Graphics Adaptor (CGA) with 16 colors and a resolution of 640 x 350 pixels. In 1987 IBM started offering the Video Graphics Array as part of its new PCs which allowed 256 different colors and a resolution of 640 x 480 pixels.

XGA and UXGA– A new technology named Enhanced Graphics Array or XGA was introduced in 1990 which allowed 16.8 million colors with a resolution of 800 x 600 pixels. The new monitors were now offering true colors that matched the human eye (human eye can detect 10 million different colors). Later the technology extended as UXGA, Ultra Extended Graphics Array which allowed 1600 x 1200 pixels.

In the 90s the LCD monitors came in the scene and gradually started competing with the CRT monitors. By the end of the 20th century, the CRT era was declining with the increasing popularity of Liquid Crystal Technology (LCD). This technology produces sharper images than the CRT monitors and the LCD monitors are significantly thinner having lower radiation emissions.

Few years’ back, LED displays came in the scene and they are gradually making its space in the market. LED technology has various advantages over LCD technology like better image quality, low power consumption, etc.

Since the beginning of computer era, there have been a number of technologies used for the display of output. The major technologies are CRT, LCD, Plasma, LED and OLED displays.

signals through a cable and the signal is decoded by the display controller which finally appears on a phosphor screen. The detailed working is as following:

As shown in the image CRTs have a conical shape and there is an electron gun or cathode ray gun at the back end of the monitor and a phosphor screen in the front. The electron gun fires a stream of electrons towards the display screen through a vacuum tube. This stream of electrons is also known as cathode rays. At the middle of the monitor, there are magnetic anodes which are magnetized in accordance with the instruction from the display controller. When electrons (cathode rays) pass through the magnetic anodes, they are pushed or pulled in one direction or other depending on the magnetic field on the anodes. This directs the electrons towards the correct part of phosphor coating inside the display glass. When electrons strikes the phosphor coated screen passing through a mesh (shadow mask or aperture grill), the phosphor lights up making a displayable dot on the computer screen. There are three different colored phosphors (Red, Green and Blue) for each pixel and the color of the pixel depends on the phosphor on which the electrons strike.

has three different phosphors for each pixel. A cathode ray strikes to one or more of these phosphors and the corresponding colored pixel appear on the screen. However high quality monitors use individual electron gun for each color which improves the image quality. Distance for two same colored phosphors (for single electron gun monitors) is known as dot pitch. Lesser the dot pitch higher is the quality of monitors.

brightness on the screen. Shadow mask is an obsolete technology in which there is a metal sheet with millions of holes to pass electrons in order to hit the phosphor coating. The shadow mask covers the entire screen thereby protecting the phosphors from stray ions (due to vacuum) and also limits the strength of the rays reducing the brightness on the monitor.

What is the resolution of the screen?–Resolution of a monitor tells how densely pixels are arranged on the screen. A combination of dot pitch and the viewable image area defines the maximum resolution of the screen. For example if a 21 inch monitor screen with a viewable area of 401mm x 298mm has a dot pitch of 0.26 mm, then its resolution is 1843 x 1370 pixels derived from a formula.

currently. LCD monitors are lightweight, compact, occupy less space, consume low power and are available in a reasonable price. Currently there are two types of LCD technology in use – Active matrix LCD technology or TFT and Passive matrix technology. The TFT technology is more reliable with better image quality while the passive matrix technology has a slower response and gradually becoming outdated.

As the name indicates, liquid crystals are the key elements of the display screen. By manipulating the crystal we can change the way they interacts with the light. There is a display controller in the monitor which receives the display signals from the video adaptor in the motherboard. The display controller controls two things – the electric signals to the liquid crystals and the back light. Structure of an LCD is shown in the below images (Also see how LCD works).

The liquid crystals used in the LCD are Twisted Nemantic (TN), a type of liquid crystals that are twisted at 90owith the surface. In this state, crystals allow the light to pass through the polarizer but on applying a voltage, they get untwisted and block the light to passing through the polarizer. The display controller starts the backlight that passes through the first piece of the glass. At the same time the display controller also send the electrical currents to the liquid crystal molecules to align and allowing the varying level of light to pass through the second piece of glass, forming the desired picture on the screen. In color monitors, each pixel is made of three liquid crystal cells fronted with red, green and blue filters. The light passing through the filtered screen forms the color what you see on the monitor. A wide range of colors are formed by varying the intensity of colored pixels.

The backlight is made of cathodes, and depending on the quality of the monitor, there may be a single cathode at the top or one at the top and one at the bottom, or two at the top and two at the bottom to improve the brightness and clarity of the monitor. These cathodes are diffused through a layer of plastic and diffusing materials.

Resolution– Unlike the CRT monitors there is no complex equation for the dot pitch and the resolution. The resolution of a monitor is simply the number of pixels contained in the matrix. Typically a 17 inch monitor has a resolution of 1280 x 1024 pixels.

In the below video Bill Hammack explains how a TFT monitor works, how it uses liquid crystals, thin film transistors and polarizers to display information.

In this field. LED monitors use light emitting diodes that acts as a performance booster in the monitors. Basically LED monitors are the LCD monitors with a LED backlight to power up the LCD panel. It means that LEDs are placed behind or around the LCD panel to enhance the luminosity and video definition of the monitor screen.

As we have seen in the above section of LCD monitors, they use a cold cathode light as backlight. In the LED monitors all the concepts are same except this backlight, which is replaced by LEDs.

There are three different types of LED monitors available based on the manner how the diodes are arranges in the monitor. These are – Direct LEDs, Edge LEDs and RGB LEDs. Both Edge and Direct LED display monitors use white diodes that are used to illuminate the LCD panel to produce the improved picture quality. The arrangement of LEDs in the monitor is shown in the below image:

In the Direct LEDs display, white diodes are placed all over the panel to produce higher quality image while the Edge LEDs display uses LEDs only on the borders of the LCD panel. Direct LEDs are generally used in the production of high definition TV whereas the Edge LEDs is mainly used in the production of computer screens. RGB LEDs display is better among the three types of LED monitors as it uses red, green and blue diodes to produce the lifelike images with amazing contrast ratio.

Both types of monitors work on the same technology. LED monitors are LCD monitors with replaced cold cathode backlight to LED backlight. Here are the differences that make the LED displays better than the LCDs

Contrast and Black level of the LED screen is better than the LCD screens because the liquid crystals cannot stop 100% of the backlight from cold cathode backlight and hence when the black screen is to be shown on the monitor, it is not completely black (as shown in the below image). But Edge LED screens perfectly show the black screen as there is no backlight at all.

illuminate tiny colored fluorescent lights to create image pixels. Each pixel is made of three such fluorescent lights – red, green and blue lights. To create a wide range of colors, intensity of these lights is varied accordingly.

There are millions of tiny cells filled with the gas like xenon and neon. They are positioned between two plates of glass known as front plate glass and rear plate glass. Two transparent electrodes covered by an insulating dielectric material and a magnesium oxide protective layer are also sandwiched between the glass plates on both sides of the cells on the entire screen.

When the CPU sends the signals to the Plasma monitor, the corresponding electrodes are charged which ionizes the gas in the intersecting cells by passing an electric current. Due to the collisions between the gas ions they release energy in the form of the photons of light which illuminate the respective cells. This process occurs thousands of times in a small fraction of second making the display faster. The released ultraviolet photons strike the phosphor material coated on the inner wall of the cell and hence phosphor electrons jump to the higher energy level. When the electron falls back to its normal state, it releases the energy as a visible light photon. Every pixel on the screen is made of three different colored phosphors – red, green and blue.

are some organic material (containing carbon, like wood, plastic or polymers.) that is used to convert the electric current into light. Since the LEDs are capable of producing different colored light, they are directly used to produce the correct color and there is no need of a backlight which saves power and space. With fast response time, wide viewing angles, outstanding contrast levels and perfect brightness, OLED displays are surely better than the existing other display technologies.

The heart of the OLED display is a stack of thin organic layers which is sandwiched between two conductors – a transparent anode and a metallic cathode, which in turn are sandwiched between two glass plates known as seal and substrate. The organic layer consists of a hole-injection layer, a hole-transport layer, an emissive layer and an electron-transport layer. When an appropriate voltage is applied, an electric current flows from cathode to anode through the organic layers. The cathode give electrons to the emissive layer of organic molecules while the anode takes equivalent electrons from the conducting layer of organic molecules. At the boundary of emissive and conductive layers, electrons and the holes are gathered. Here electrons are recombined with the holes by releasing energy in the form of photon of light. Hence the organic layer emits the light to produce the display. The color of the light depends on the type of organic molecules while the brightness depends on the amount of the current applied. By maximizing the recombination process in the emissive layer the output light can be improved in OLED devices. Thus the emissive layer is slightly doped with highly fluorescent molecules to enhance the electro-luminescent efficiency and control of color.

·Comparing it with the LCD devices, OLED displays can be viewed from different angles as they are “emissive” devices i.e. they emit light rather than modulating transmitted or reflected light.

Firstly polarization, in this we will get to another terms which are polarized light and unpolarized light. So a polarized light wave is that light wave in which vibration occur in a single plane and an unpolarized light wave is that light wave in which vibration occur in more than one plane. Now let’s finally understand polarization. Polarization is a process of transforming unpolarized light wave into polarized light wave.

This is older technology which is not used today. In CRT monitors there was a cathode ray tube due to which it is called CRT monitors. It consists of the electron gun which emits electron on the phosphorous screen and with the help of it image is formed on the screen. The signals that is send from the video adapter reaches to the electronic gun through cables. There are three electronic guns for each RGB color Red, Green, and Blue. These three color mixes with each other and form other colors. The electrons beams emitted from the electronic gun can be focussed in different direction using magnetic force. So that it can reach on the whole screen and produce display. The electron beams when hit the phosphorus screen it produces Red, Green, and Blue colours. The CRT monitor was heavy, large and bulky in size. It consumes more energy. The disadvantage of this technology is that it emits radiations which are harmful for human eyes and health. Due to this reason the CRT monitor is now replaced with the LCD monitor.

The flat panel display replaced the CRT. The flat panel display takes small space as compare to the CRT. It is small in size and consumes less power. Now days mostly computer and laptops uses flat panel display. Flat panel display does not emit any harmful radiation. Flat panel display uses three types of technology:

Now the first display panel type we have got is liquid crystal display or LCD it is a type of display panel that uses liquid crystals technologyalong with polarizers and a cold cathode fluorescent lamp as backlight to provide lightning. These liquid crystals do not emit light directly instead of it. They use a backlight or reflector to illuminate screen and produce image in colour or monochrome. The LCD works better in sunlight. The electricity passes through the liquid crystal and produce image.The color accuracy of the LCD is not very good. The LCD works on three things:

When light emits from source then the light wave vibrates in different direction in horizontal, vertical and diagonal. Then the polarization filters which are sheet of plastic which consists of vertical lines which are very near to each other. The important thing about filter is that when it is place in front of light then only vertical waves can pass through this filter. The horizontal waves are blocked by the filter. If we rotate this filter by 90 degree then this filter will block the vertical waves and pass the horizontal waves. Then we have liquid crystals which was discovered by an Australian scientist in 1888 which is state between the solid and liquid. The interesting thing about liquid crystal is that when the current is passes through it. The molecules changes its direction.

This type of LCD used active matrix technology which means that at every pixel transistor and capacitor is separately attached. The TFT contrast is better than LCD. But the disadvantage is that it consume more power due to which the battery timing of the mobile or laptop is minimum and also from the side the display view is not good. TFT technology is not available in the latest mobiles.

IPS LCD is the advanced form of the TFT technology the viewing angle and colour contrast is better than TFT. In IPS technology there are two transistors for each pixel and also the back light is maximum. It consumes less power as compare to TFT due to which it’s battery life is better than TFT.

The next display panel is light emitting diode or simply led. A led display panel also uses liquid crystal technology but instead of cold cathode fluorescent lamps as back lightning led display panel use an area of small light emitting diodes or LEDs as backlighting to illuminate the screen.

LED might seem like a new type of screen but in fact the LED is just an LCD screen but instead of using fluorescent light as the backlight it uses LEDs  this gives the LED screen some new advantages for example it’s more energy efficient since LEDs consume less power also LED screens can be made very thinner than LCDs because they don’t have that bulky backlight. LEDs also have slightly more accurate colors than LCDs what’s also nice about LEDs is that black is slightly more black than on an LCD screen.

So the next display panel is organic light emitting diode or simply OLED. OLED display panel is made by putting a series of organic thin films between two conductors and when electric current is applied to this type of structure it emits a bright light unlike LCDS and LEDS.They don’t require backlight so they can be thinner and way lesser.So finally OLED uses an organic substance that glows when electric current is introduced and these displays can be thin and flexible too. Now to show something in OLED display it do not require all the display to turn on and only those pixel work which want to display something and other pixels will remain off. Due to which the black portion of the OLED display looks very good compare to LCD. It also consumes less power due to which the battery life will be good. The contrast ratio of OLED technology is better than LCD because the black pixels remain off. The disadvantage is that in sunlight its light is compromised and we may face problem in watching compare to an LCD display. LCD based phone is relatively cheaper than OLED display phone. The screen of the OLED display is very thinner because it does not need back light. Due to which OLED display phone is very thinner and more flexible than LCD phones. The very important benefit of it is that it is folded display. So we can decrease the phone size by folding the screen.

Now the next display panel is active matrix organic light emitting diode or simply AMOLED in AMOLED display panel. The first two words a and m refers to active and matrix respectively. The active matrix refers to the technology which is used for addressing pixels. AMOLED display panel uses a thin film transistor or TFT which contains a storage capacitor which maintains the line pixel states. So AMOLED display panel is a type of OLED which uses active matrix technology.The AMOLED is called active matrix because it consists of different layers for display formation. The anode layer is integrated with thin film transistor TFT which means it does not depend upon on the external circuit to glow the pixel.

Now the last display type we have got is super active matrix organic light emitting diode or simply assemble it as S-AMOLED is an AMOLED display which has an integrated touch function. So instead of having a layer which recognizes touches on top of screen that layer is embedded directly into screen assembly is a marketing term that is used by Samsung which refers to a display technology. Now you may be thinking what is the difference between S-AMOLED and AMOLED. So the term super make it distinguishable from its older version AMOLED and S-AMOLED are not only similar by name but also similar in function. The difference between them is the integrated touch function technology which S-AMOLED have and AMOLED have not. The super AMOLED is integrated with the touch sensor. As in the AMOLED we were used touch sensor digitizer which was integrated in the S-AMOLED due to which the thickness was decreased and due to removal of the touch sensor digitizer battery consumption is also decreased. In S-AMOLED light reflection is less as compare to the AMOLED. Both shares the same pixel arrangement

Gaspar, D. J. & Polikarpov, E. OLED Fundamentals: Materials, Devices, and Processing of Organic Light-Emitting Diodes. (Taylor & Francis Group, Boca Raton, FL, 2015).

Tull, B. R. et al. High brightness, emissive microdisplay by integration of III-V LEDs with thin film silicon transistors. SID Symp. Digest Tech. Papers46, 375–377 (2015).

Takeda, A. et al. A super-high image quality multi-domain vertical alignment LCD by new rubbing-less technology. SID Symp. Digest Tech. Papers29, 1077–1080 (1998).

Lee, S. H., Lee, S. L. & Kim, H. Y. Electro-optic characteristics and switching principle of a nematic liquid crystal cell controlled by fringe-field switching. Appl. Phys. Lett.73, 2881–2883 (1998).

Kim, H. J. et al. Optical efficiency enhancement in wide color gamut LCD by a patterned quantum dot film and short pass reflector. SID Symp. Digest Tech. Papers47, 827–829 (2016).

Soh, M. Y. et al. Design and characterization of micro-LED matrix display with heterogeneous integration of GaN and BCD technologies. IEEE Trans. Electron Devices66, 4221–4227 (2019).

Ahn, H. A., Hong, S. K. & Kwon, O. K. An active matrix micro-pixelated LED display driver for high luminance uniformity using resistance mismatch compensation method. IEEE Trans. Circuits Syst. II: Express Briefs65, 724–728 (2018).

Chaji, G. R. & Nathan, A. Parallel addressing scheme for voltage-programmed active-matrix OLED displays. IEEE Trans. Electron Devices54, 1095–1100 (2007).

Templier, F. et al. A novel process for fabricating high-resolution and very small pixel-pitch GaN LED microdisplays. SID Symp. Digest Tech. Papers48, 268–271 (2017).

Templier, F. et al. Advanced solutions for high-performance GaN MicroLED displays. Proceedings of SPIE 10918, Gallium Nitride Materials and Devices XIV. (SPIE, San Francisco, 2019).

Takita, Y. et al. Highly efficient deep-blue fluorescent dopant for achieving low-power OLED display satisfying BT.2020 chromaticity. J. Soc. Inf. Disp.26, 55–63 (2018).

Olivier, F. et al. Shockley-Read-Hall and Auger non-radiative recombination in GaN based LEDs: a size effect study. Appl. Phys. Lett.111, 022104 (2017).

Chen, S. M., Sun, X. W. & Kwok, H. S. Hybrid analog-digital driving method for high definition AMOLED. SID Symp. Digest Tech. Papers45, 1514–1517 (2014).

Hosoumi, S. et al. Ultra-wide color gamut OLED display using a deep-red phosphorescent device with high efficiency, long life, thermal stability, and absolute BT.2020 red chromaticity. SID Symp. Digest Tech. Papers48, 13–16 (2017).

Utsumi, Y. et al. Improved contrast ratio in IPS-Pro LCD TV by using quantitative analysis of depolarized light leakage from component materials. SID Symp. Digest Tech. Papers39, 129–132 (2008).

Hoffman, D. M., Stepien, N. N. & Xiong, W. The importance of native panel contrast and local dimming density on perceived image quality of high dynamic range displays. J. Soc. Inf. Disp.24, 216–228 (2016).

Guarnieri, G., Albani, L. & Ramponi, G. Minimum-error splitting algorithm for a dual layer LCD display—part I: background and theory. J. Display Technol.4, 383–390 (2008).

Guarnieri, G., Albani, L. & Ramponi, G. Minimum-error splitting algorithm for a dual layer LCD display—part II: implementation and results. J. Display Technol.4, 391–397 (2008).

Daly, S. et al. Viewer preferences for shadow, diffuse, specular, and emissive luminance limits of high dynamic range displays. SID Symp. Digest Tech. Papers44, 563–566 (2013).

Nishimura, J. et al. Super bright 8K LCD with 10,000 nit realized by excellent light-resistance characteristics of IGZO TFT backplane. SID Symp. Digest Tech. Papers51, paper 3.1 (2020).

Daly, S. & Feng, X. F. Bit-depth extension: overcoming LCD-driver limitations by using models of the equivalent input noise of the visual system. J. Soc. Inf. Display13, 51–66 (2005).

Guo, W. J. et al. The impact of luminous properties of red, green, and blue mini-LEDs on the color gamut. IEEE Trans. Electron Devices66, 2263–2268 (2019).

Kim, H. M. et al. Ten micrometer pixel, quantum dots color conversion layer for high resolution and full color active matrix micro-LED display. J. Soc. Inf. Disp.27, 347–353 (2019).

Chen, H. W. et al. Liquid crystal display and organic light-emitting diode display: present status and future perspectives. Light: Sci. Appl.7, 17168 (2018).

AU Optronics Corp. AUO Showcases Mini LED Backlit LCDs Across Diverse Verticals to Seize Smart Living Market Opportunities. https://www.auo.com/en-global/New_Archive/detail/News_Archive_Technology_190513 (2019).

Handschy, M. A., McNeil, J. R. & Weissman, P. E. Ultrabright head-mounted displays using LED-illuminated LCOS. Proceedings of SPIE 6224, Helmet- and Head-Mounted Displays XI: Technologies and Applications. (SPIE, Florida, 2006).

Zhang, L. et al. Monochromatic active matrix micro-LED micro-displays with >5,000 dpi pixel density fabricated using monolithic hybrid integration process. SID Symp. Digest Tech. Papers49, 333–336 (2018).

Fan, R., Zhang, X. N. & Tu, Z. T. Influence of ambient temperature on OLED lifetime and uniformity based on modified equivalent lifetime detection. J. Soc. Inf. Disp.27, 597–607 (2019).

TFT LCD image retention we also call it "Burn-in". In CRT displays, this caused the phosphorus to be worn and the patterns to be burnt in to the display. But the term "burn in" is a bit misleading in LCD screen. There is no actual burning or heat involved. When you meet TFT LCD burn in problem, how do you solve it?

When driving the TFT LCD display pixels Continously, the slightly unbalanced AC will attract free ions to the pixels internal surface. Those ions act like an addition DC with the AC driving voltage.

Those burn-in fixers, screen fixer software may help. Once the Image Retention happened on a TFT, it may easy to appear again. So we need to take preventive actions to avoid burn in reappearing.

For normal white TFT LCD, white area presenting minimal drive, black area presenting maximum drive. Free ions inside the TFT may are attracted towards the black area (maximum drive area)

Different displays have different characteristics, just tell Panox Display your application, and operating environment, Panox Display will suggest a suitable display for you.

But Panox Display is not a school, if customers don`t know the basic knowledge to design circuit boards, we suggest using our controller board to drive the display.

If you don`t know or don`t want to write a display program on Raspberry Pi, it`s better to get an HDMI controller board from us, and Panox Display will send a config.txt file for reference.

TFT is an abbreviation for Thin Film Transistor, a flat panel display used to improve the operation and utility of LCD screens. In order to portray an appearance to the audience, a liquid crystal display (LCD) utilizes a crystalline-filled fluid to modify rear lighting polarized origin through the use of an electromagnetic force among two relatively thin metal wires such as indium oxide (ITO). However, color TFT displays are associated with this method, which can be employed in both divided and pixelated display systems.

With motion pictures displayed on an LCD, the intrinsic sluggish rate of increase between liquid phases over a significant number of pixel components can be an issue due to capacitance impacts, which can create a blurring of the visuals. Placing a high-velocity LCD control device inside the formation of a thin-film transistor immediately next to the cell component just on a glass screen, the issue of LCD picture speed may be substantially improved, and image blur can be eliminated for all useful purposes entirely.

Organic light-emitting diodes (AMOLEDs) are a type of flat light-emitting advanced technologies that are created by interspersing a succession of organic thin sheets over two conducting conductors. An electrical charge causes a brilliant light to be produced when the current flows. AMOLED displays are light-emitting screens that do not require a backlight, making them thinner and more energy-efficient than liquid crystal displays (LCDs) (which will need a white backlight).

AMOLED displays are not only thin and fuel-intensive, but they also deliver the highest image quality available, so they can be made translucent, elastic, bendable, or even rollable and stretchy in the future, allowing for a variety of applications. AMOLEDs are a revolutionary technology in terms of display devices! It is possible to create an AMOLED by sandwiching a sequence of thin films across phase conductors. Electric charge causes a brilliant light to be emitted when the current flows through the coil.

The color display is fantastic. Color intensity, sharpness, and luminance settings that are second to none and can be customized to meet the needs of any application.

Half-Life has been expanded. TFT displays have a far longer half-life than its LED equivalents, and they are available in a number of sizes, which might have an effect on the device"s half-life based on the phone"s usage as well as other variables. Touch panels for TFT screens can be either resistant or capacitance in nature.

As it is more affordable than capacitive, resistive is typically the preferred option. However, capacitive technology is compatible with a wide range of contemporary smartphones and digital gadgets.

They rely on backlight to give illumination rather than generating their own light. Hence they require constructed light-creating diodes (LEDs) in their backlit display framework to ensure enough brightness.

Backlighting is unnecessary for AMOLEDs. LCDs produce images by selectively blocking parts of the illumination, whereas AMOLEDs produce light. AMOLEDs utilize less energy than LCDs since they don"t need backlighting. This is critical for battery-powered devices such as phones.

While AMOLED light-emitting sheets are lightweight, the substrate can also be elastic rather than stiff. AMOLED films are not limited to glass-like LEDs and LCDs.

AMOLEDs offer 170-degree ranges of vision. LCDs operate by obscuring the light. Hence they have intrinsic viewing obstacles. In addition, AMOLEDs have a substantially wider viewing spectrum.

AMOLEDs outperform LEDs. Since AMOLED organic coatings are less than LED inorganic crystal levels, AMOLED conducting and particle emitters layers can just be multi-layered. Also, LEDs and LCDs need glass backing, which absorbs light. AMOLEDs don"t need it.

AMOLEDs seem to be simpler to implement and larger. AMOLEDs are constructed of polymers and may be produced into big sheets. It takes a lot of extra liquid crystals to build and set down.

While red and green AMOLED sheets have a greater lifespan (46,000 to 230,000 hours), azure compounds have significantly shorter longevity (up to roughly 14,000 hours).

Due to the fact that AMOLED displays inherently emit illumination, they do not need a backlight when used on a monitor screen. Conversely, LCDs require backlights since the liquid crystals themselves are incapable of producing light under their own. Direct light emission from AMOLED displays also allows for the developing of lightweight display devices than others using TFT LCDs.

LCD displays have a higher brightness than AMOLED panels. This is owing to the LCD"s usage of led backlight, which may provide a brilliant illumination of the entire display. Despite the fact that AMOLEDs produce high levels of brilliance from their illumination, they will never be able to match the intensity of LCD lighting.

LCD screens use less power than AMOLED displays, which provides a slight advantage. The amount of energy consumed by AMOLED displays is dependent on the intensity of the screen. Lowered luminance results in lower energy usage, however, it might not be the best solution because the contrast would suffer as a result of the decreased brightness. In some situations, such as when to use an AMOLED device in direct sunlight, it is not an optimal situation.

However, the backlit keys of TFT displays account for the majority of their power usage. TFT screens" efficiency is considerably improved when the backlight is set to a lesser brightness level than the default setting. For example, replacing the light of an LCD TV with just an Led flash will have no effect on the image quality, but will result in lower power usage than replacing the light of an AMOLED TV.

With the exception of phones, numerous other technologies make use of displays to allow customers to engage in direct communication with them. To determine whether or not TFT LCD will be able to withstand the development of AMOLED innovation, we should first review the benefits of LCD technology. The backlighting quality ensures that whites are strong and brightness is superb but will deplete a battery much more quickly than just an AMOLED display. Furthermore, the cost of LCD screens is a considerable consideration. In addition to being less expensive and more easily accessible, they are produced in standard industry sizes, allowing them to be purchased for innovative products with relative ease.

Apple has brought mini LED toiPad Pro, and is also working on micro LED technology. Here"s what to expect from the new display technologies set to take over from TFT LCD and OLED.

Display technology has been slow to change, with the industry seemingly taking decades to move from one to the next. Cathode ray tube (CRT) screens hung around for ages until thin and light TFT LCD screens became cheap and attractive enough for consumers to adopt.

Inevitably, when a technology has started to see wide adoption by the industry, the attention then turns to what is on the way. With supply chain reports of Apple"s interest in microLED and mini LED, the use of mini LED in the 12.9-inch iPad Pro, and the potential use of both technologies in future products, this has prompted a lot of interest from observers.

The two technologies are interesting, and each provides its own benefits to the device table. In the case of microLED, it introduces a major fundamental change in the way devices are designed, produced, and appear to consumers.

One of the older and more established display technologies in use today, TFT LCD stands for Thin Film Transistor Liquid Crystal Display. It has been in use in screens for decades, most commonly in notebooks, but it is also used in tablets, smartphones, and other mobile devices.

The technology is relatively similar to the segmented screen of a calculator, in that it relies on a series of layers to sandwich a liquid crystal material. When a current is applied, the properties of the liquid crystal material can change, and so it affects how light passes through it.

In a simple calculator display, pockets are formed in the layers to contain the liquid crystal material in a specific formation, and applying current in these areas allows certain segments to become opaque while others remain transparent or translucent. Controlling which of these segments have current applied to them in different combinations shows different numbers.

Instead of a segment of a number, there are instead millions of little pockets across the screen in a grid of pixels. Using pockets with color filters for red, green, and blue, these segments can be used to show different combinations of colors.

Polarizing filters are on either side of the display sandwich, used to force light to pass through in a specific way. The LCD sections can block the light from passing through, resulting in a dark or black pixel in that section.

An important element of the system is light, which is transmitted from behind the TFT LCD stack. Without that light, the screen will appear dark and largely unviewable to the user.

For many years, this has involved the use of LEDs in a backlight, spread out across the edges of the screen and funneled across to illuminate the entire backlight.

TFT LCD offers a cheap, cost-efficient, and highly reliable way to include a display in their device for device producers. The long lifespan of the technology means it is already quite mature, though with relatively few ways to expand the technology in new directions.

TFT LCD has been a staple of Apple"s product range for many years, from MacBooks and iMacs to the iPhone and iPad. While Apple is certainly looking into other areas to improve its products" displays, it at least has a well-worn technology it can fall back on if required.

The next major display technology for thin portable screens after TFT LCD was OLED, which means Organic Light Emitting Diode. While the names are dramatically different, there are many elements of OLED that borrow heavily from TFT LCD, but there are still some fundamental differences.

Like TFT LCD, OLED uses thin film layers, a grid of pockets filled with a liquid to create pixels, and colored filters to change the color of light. Unlike TFT LCD, the big differentiator is the liquid that is put into that film sandwich.

An organic compound is used, one that emits light when a current is passed through it. This means that each pixel is self-illuminating and eliminates the need for a backlight.

This offers quite a few advantages over TFT LCD, such as an OLED screen being thinner by not requiring a backlight in order to function. This can also make the display assembly lighter and simpler to construct in some cases.

By having a light source per pixel, this also means that OLED can provide far higher contrast levels than TFT OLED. A TFT screen generally won"t show pure black for some pixels, as the backlight will be on for all pixels equally, and so some light will bleed through and show a very dark grey instead.

There is also the potential for power savings, as OLED requires power to illuminate only the pixels it requires. TFT LCD typically requires all of the LEDs in the backlight to be on, regardless of the type of image being shown.

Since there"s no backlight, OLED is also a great candidate for flexible displays, such as those used in foldable devices like the Samsung Galaxy Fold and the rumored "iPhone Fold."

While great, OLED panels have their own issues, such as the relatively high cost of production due to a need for clean environments devoid of dust and water. Each is easily capable of contaminating the display, ruining it partially useless.

There has been some talk about Apple using OLED instead of TFT LCD in some future iPad Pro models, which could allow for even thinner tablets with higher contrast levels. However, the typically longer use of a tablet could lead to burn-in or a loss of brightness over time for the OLED panels.

To fix this last point, it was rumored that Samsung was adding a distribution chamber to an OLED production line, which would allow the stacking of emitting layers. With these extra layers, the OLED screen"s lifespan could be extended beyond typical durations.

The use of the technology isn"t necessarily limited to tablets and smartphones. There have been rumors over the years claiming Apple was going to add OLED to its MacBook Pro line, though so far