lcd panel connect to computer power supply in stock

This website is using a security service to protect itself from online attacks. The action you just performed triggered the security solution. There are several actions that could trigger this block including submitting a certain word or phrase, a SQL command or malformed data.

It is estimated that there are around one billion personal computers around the world, and with every single desktop computer, there is also a monitor attached to it. Every day, hundreds of computer monitors break down, and if you have a LCD monitor that you bought fairly recently and have questioned why it won"t turn on anymore, it"s most likely a power problem that can be fixed to save you hundreds of dollars. This guide will specialize on the computer monitor model LG L196WTQ-BF, but most monitors will follow similar design and can generally be fixed using the same instructions.

There aren’t many components as boring as the power supply in your PC, but the new Aorus P1200W 80+ Platinum modular power supply is looking to change that. The unit includes an LCD screen on the side that allows you to quickly monitor system information or just add a little more bling to your build.

The main purpose of the screen is to show system information like your total power consumption, fan speed, and PSU temperature. However, you can customize it with just about anything. The screen supports custom text, image files, GIFs, and even MP4s, so you can loop your favorite clip or perhaps even play a full movie.

Gigabyte hasn’t listed any information about the screen, so the resolution and refresh rate might kill the experience. Under the screen is a thin RGB strip with some Aorus branding, which you can customize and sync through Gigabyte’s RGB Fusion 2.0 software.

Glitz isn’t all that makes the P1200W stand out. As a high-end unit capable of taking on the best power supplies, it comes with 80+ Platinum certification, flat modular cables, Japanese capacitors, and a slew of temperature, current, and voltage protections.

It isn’t short of connections, either. It comes with 24-pin motherboard power, two 8-pin CPU connectors, six 8-pin PCIe cables, 16 SATA connections through four cables, and two Molex connectors. All of the cables are fully modular, too, so you only have to plug in what ones you’ll use.

Keeping everything cool is a single 140mm fan, which stays idle if the load is under 20%. The fan also has a unique feature that lets you reverse its direction to blow dust out that’s accumulated inside the power supply. You can set the fan to do that every time you turn on your computer, or you can do it manually.

Unlike a lot of high-wattage power supplies, the Aorus P1200W isn’t any bigger than a standard ATX unit. It measures only 160mm in length compared to the 200mm seen on most other 1200W PSUs.

Gigabyte hasn’t released any information on pricing or where you’ll be able to find the P1200W. At the time of publication, it’s not available through Gigabyte’s online store, and the only retailer in the “where to buy” section doesn’t have it listed. Once it starts making the rounds, though, it will likely be on the premium end of things.

Note: Your email address is used only to let the recipient know who sent the email and in case of transmission error. Neither your address nor the recipient"s address will be used for any other purpose.

To use a desktop computer, a monitor is required. The monitor let you see the operating system GUI and software applications, like a video game, document editor, or Internet browser.

All computer monitors have at least two cables, a power cable and a data cable. The power cable connects to the power outlet, or better, a surge protector, and is what allows the monitor to turn on. The other cable is a data cable and is what allows the picture (data) from your computer to be displayed. The type of cable can vary depending on the type of connection your video card and monitor supports. The cable may be a VGA, S-Video, DVI, HDMI, DP (DisplayPort), or USB-C. VGA and DVI are older connections, whereas HDMI, DisplayPort, and especially USB-C are newer.

Monitors with USB ports or card readers also have a USB cable that must be connected to the computer if you want to use these features. Older monitors with speakers built-in to them may also have audio cables that connect the monitor to the computer. However, newer monitors with speakers no longer need these cables.

If you purchased a new monitor, it should include a cable to connect to your computer. However, if your video card does not support that type of cable, you need to purchase a cable supported by the computer. Alternatively, you can purchase a converter that converts one video signal to another signal supported by the computer.

Generally speaking, today, we recommend using an HDMI cable. With higher quality displays, you may want to use a DisplayPort for higher refresh rates.

The VGA and DVI cables have two screws, one on either side of the connector. Make sure the cable screws line up and then alternate turning each screw until they are secure.

If not already done, connect the flat end of the monitor power cord (left cable end shown below) to the back of the monitor. The power cord may also be built into the back of the monitor.

Turn on the computer and turn on the monitor. The power button for the monitor is often found on the front or bottom of the monitor on the right side.

Plug the USB end of the adapter into a USB charging port on your second display. If your display doesn"t have a USB charging port, plug the USB end into any standard USB Type-A charger with 5W (5V/1A).

To change the settings for your adapter, update the firmware, and more, you"ll need the Microsoft Wireless Display Adapter app. Here"s how to install it from the Microsoft Store:

Select Update & security. If an update is available, select Update. You"ll need to keep the app open and stay connected to the adapter until updates are completed.

To keep your adapter up to date, turn on Update adapter automatically. Updates will take place when updates are available and your adapter is connected to your Windows PC.

Get better performance when your Windows PC and adapter are connected to the same Wi-Fi network. If you need to change the network your adapter is connected to, here"s how:

In 1987, the year Gary Rosenzweig started college,Drexel University in Philadelphia had the foresight to require every student to purchase a computer. Better still, they required that computer be a Macintosh.

From the 1987 Macintosh SE with two floppy disk drives and a little monochrome screen, to his current 2009 Mac Pro with two four-core Xeon processors, Gary has always owned a Mac.

His Mac was his primary tool used in creating games and websites from 1994 to the present day. But it wasn’t until 2007 that he took his love of Macs to the professional level with the launch of the MacMost site and video podcast.

At first,MacMost covered Apple news each week. But soon it evolved into a more frequent show with tutorials, tips, news, and reviews.The website grew as well, featuring iPhone games, ringtones, a weekly newsletter, and other features.

Gary has also written many books, most on programming using Macromedia/Adobe software like Director and Flash. He lives in Denver, Colorado, with his wife,Debby, and daughter, Luna. Also a dog and too many cats.

When pressing the power button to power up the computer, the fan and LED indicators perform normally, but nothing gets displayed on monitor at all, please follow the instructions below to troubleshoot:

2.If the cables for the front panel of the case are damaged, the system may not be able to boot up normally using the power button. Please try to remove the boot cables of the front panel, then “short circuit” the Power Switch pin directly using a metal object (i.e. screw driver) to confirm whether the system can boot up normally.

1.Please visit MSI’s official website and click "Search” at the top-right corner, then enter system"s model. Using “MEG Z590 ACE” for example, we then press “Enter” to search for said model.

If you are unable to boot up a system which has two or more memories installed, please first boot up the system with one memory to confirm whether the system can boot up, then install the remaining stick(s) of memory/ies to eliminate potential memory problems.

2.Please connect your monitor to the display output on the motherboard to have the motherboard"s internal display output display. (If your CPU does not have an internal display output function, please skip this step). Disconnect the power, then first remove the standalone graphics card. Connect the monitor cable to the display output interface behind the motherboard (as shown in the red frame part in the image below). If the monitor have display after booting up, this means that the standalone graphics card may have an issue.

Check the debug status of the motherboard’s EZ Debug LED indicators: When errors in related hardware occur during the system"s booting process, the corresponding LED indicator will remain constantly on, hence allowing you to quickly determine the point of failure.

3.If the system normally boots up in this configuration, damages to certain hardware may cause the booting process to fail. Please try to reconnect the devices individually to identify the damaged device.

Discharge to clear CMOS: After the computer"s power supply is completely disconnected, use a metal object to short circuit the CMOS jumper (JBAT1), or remove the CMOS battery on the motherboard and wait 5 minutes before reinstalling. Once done, try booting up the system again.

You may be able to connect one or more external displays to your Mac (you may need a video cable or adapter for each display). See the Apple Support article Adapters for the Thunderbolt 4, Thunderbolt 3, or USB-C port.

For each display, securely connect a video cable (and adapter, if necessary) from a video output port on your Mac to the video input port on the display. See About the video ports.

You can connect one or more external displays, depending on your Mac.For Mac computers with the Apple M1 Chip: You can connect a single external display to your Mac. Docks don’t increase the number of displays you can connect. On a Mac mini with M1 chip, you can connect a second display to the HDMI port. See the Apple Support article Mac computers with Apple silicon.

For Mac computers with Thunderbolt 3 (USB-C): You can connect a single display to each port. If you connect multiple Thunderbolt devices to each other, the Thunderbolt 3 display must be the last device in the chain. If your Thunderbolt 3 display has USB ports, those can be used for data and power.

For Mac computers with Mini DisplayPort, Thunderbolt, or Thunderbolt 2: You can connect up to two displays. If the displays themselves have Thunderbolt ports, you can connect one display to another, and then connect one of the displays to a Thunderbolt port on your Mac. If your Mac has two Thunderbolt ports, you can connect each display to separate Thunderbolt ports on your Mac. A DisplayPort device must be the last device in a chain of connected Thunderbolt devices. See Connect a display, TV, or projector to Mac.

For Mac computers with Thunderbolt 4 (USB-C) and HDMI ports: You can connect up to four external displays to your Mac, depending on your Mac model. See the Apple Support article Connect a display to your Mac.

Note:Only the device directly connected to your Mac receives power from the computer’s Thunderbolt port. The other devices in the chain must be powered by separate power adapters.

You can arrange your displays in any configuration to create an extended desktop. For example, you can set your external display side by side with your Mac to create one large continuous desktop.

If more than two displays are connected to your Mac, you can specify that some displays use mirroring (showing the entire desktop) and other displays show the extended desktop (displaying the desktop across two or more displays). For example, if you have three displays, you can have two displays showing the same information and the third display showing the extended desktop.Press and hold the Option key and drag one display icon onto another display icon to mirror those two displays.

A computer monitor is an output device that displays information in pictorial or textual form. A discrete monitor comprises a visual display, support electronics, power supply, housing, electrical connectors, and external user controls.

The display in modern monitors is typically an LCD with LED backlight, having by the 2010s replaced CCFL backlit LCDs. Before the mid-2000s,CRT. Monitors are connected to the computer via DisplayPort, HDMI, USB-C, DVI, VGA, or other proprietary connectors and signals.

Originally, computer monitors were used for data processing while television sets were used for video. From the 1980s onward, computers (and their monitors) have been used for both data processing and video, while televisions have implemented some computer functionality. In the 2000s, the typical display aspect ratio of both televisions and computer monitors has changed from 4:3 to 16:9.

Modern computer monitors are mostly interchangeable with television sets and vice versa. As most computer monitors do not include integrated speakers, TV tuners, nor remote controls, external components such as a DTA box may be needed to use a computer monitor as a TV set.

Early electronic computer front panels were fitted with an array of light bulbs where the state of each particular bulb would indicate the on/off state of a particular register bit inside the computer. This allowed the engineers operating the computer to monitor the internal state of the machine, so this panel of lights came to be known as the "monitor". As early monitors were only capable of displaying a very limited amount of information and were very transient, they were rarely considered for program output. Instead, a line printer was the primary output device, while the monitor was limited to keeping track of the program"s operation.

Multiple technologies have been used for computer monitors. Until the 21st century most used cathode-ray tubes but they have largely been superseded by LCD monitors.

The first computer monitors used cathode-ray tubes (CRTs). Prior to the advent of home computers in the late 1970s, it was common for a video display terminal (VDT) using a CRT to be physically integrated with a keyboard and other components of the workstation in a single large chassis, typically limiting them to emulation of a paper teletypewriter, thus the early epithet of "glass TTY". The display was monochromatic and far less sharp and detailed than on a modern monitor, necessitating the use of relatively large text and severely limiting the amount of information that could be displayed at one time. High-resolution CRT displays were developed for specialized military, industrial and scientific applications but they were far too costly for general use; wider commercial use became possible after the release of a slow, but affordable Tektronix 4010 terminal in 1972.

Some of the earliest home computers (such as the TRS-80 and Commodore PET) were limited to monochrome CRT displays, but color display capability was already a possible feature for a few MOS 6500 series-based machines (such as introduced in 1977 Apple II computer or Atari 2600 console), and the color output was a speciality of the more graphically sophisticated Atari 800 computer, introduced in 1979. Either computer could be connected to the antenna terminals of an ordinary color TV set or used with a purpose-made CRT color monitor for optimum resolution and color quality. Lagging several years behind, in 1981 IBM introduced the Color Graphics Adapter, which could display four colors with a resolution of 320 × 200 pixels, or it could produce 640 × 200 pixels with two colors. In 1984 IBM introduced the Enhanced Graphics Adapter which was capable of producing 16 colors and had a resolution of 640 × 350.

By the end of the 1980s color progressive scan CRT monitors were widely available and increasingly affordable, while the sharpest prosumer monitors could clearly display high-definition video, against the backdrop of efforts at HDTV standardization from the 1970s to the 1980s failing continuously, leaving consumer SDTVs to stagnate increasingly far behind the capabilities of computer CRT monitors well into the 2000s. During the following decade, maximum display resolutions gradually increased and prices continued to fall as CRT technology remained dominant in the PC monitor market into the new millennium, partly because it remained cheaper to produce.

There are multiple technologies that have been used to implement liquid-crystal displays (LCD). Throughout the 1990s, the primary use of LCD technology as computer monitors was in laptops where the lower power consumption, lighter weight, and smaller physical size of LCDs justified the higher price versus a CRT. Commonly, the same laptop would be offered with an assortment of display options at increasing price points: (active or passive) monochrome, passive color, or active matrix color (TFT). As volume and manufacturing capability have improved, the monochrome and passive color technologies were dropped from most product lines.

The first standalone LCDs appeared in the mid-1990s selling for high prices. As prices declined they became more popular, and by 1997 were competing with CRT monitors. Among the first desktop LCD computer monitors was the Eizo FlexScan L66 in the mid-1990s, the SGI 1600SW, Apple Studio Display and the ViewSonic VP140vision science remain dependent on CRTs, the best LCD monitors having achieved moderate temporal accuracy, and so can be used only if their poor spatial accuracy is unimportant.

High dynamic range (HDR)television series, motion pictures and video games transitioning to widescreen, which makes squarer monitors unsuited to display them correctly.

Organic light-emitting diode (OLED) monitors provide most of the benefits of both LCD and CRT monitors with few of their drawbacks, though much like plasma panels or very early CRTs they suffer from burn-in, and remain very expensive.

Radius of curvature (for curved monitors) - is the radius that a circle would have if it had the same curvature as the display. This value is typically given in millimeters, but expressed with the letter "R" instead of a unit (for example, a display with "3800R curvature" has a 3800mm radius of curvature.

Dot pitch represents the distance between the primary elements of the display, typically averaged across it in nonuniform displays. A related unit is pixel pitch, In LCDs, pixel pitch is the distance between the center of two adjacent pixels. In CRTs, pixel pitch is defined as the distance between subpixels of the same color. Dot pitch is the reciprocal of pixel density.

Pixel density is a measure of how densely packed the pixels on a display are. In LCDs, pixel density is the number of pixels in one linear unit along the display, typically measured in pixels per inch (px/in or ppi).

Contrast ratio is the ratio of the luminosity of the brightest color (white) to that of the darkest color (black) that the monitor is capable of producing simultaneously. For example, a ratio of 20,000∶1 means that the brightest shade (white) is 20,000 times brighter than its darkest shade (black). Dynamic contrast ratio is measured with the LCD backlight turned off. ANSI contrast is with both black and white simultaneously adjacent onscreen.

Color depth - measured in bits per primary color or bits for all colors. Those with 10bpc (bits per channel) or more can display more shades of color (approximately 1 billion shades) than traditional 8bpc monitors (approximately 16.8 million shades or colors), and can do so more precisely without having to resort to dithering.

Color accuracy - measured in ΔE (delta-E); the lower the ΔE, the more accurate the color representation. A ΔE of below 1 is imperceptible to the human eye. A ΔE of 2–4 is considered good and requires a sensitive eye to spot the difference.

Viewing angle is the maximum angle at which images on the monitor can be viewed, without subjectively excessive degradation to the image. It is measured in degrees horizontally and vertically.

Refresh rate is (in CRTs) the number of times in a second that the display is illuminated (the number of times a second a raster scan is completed). In LCDs it is the number of times the image can be changed per second, expressed in hertz (Hz). Determines the maximum number of frames per second (FPS) a monitor is capable of showing. Maximum refresh rate is limited by response time.

Response time is the time a pixel in a monitor takes to change between two shades. The particular shades depend on the test procedure, which differs between manufacturers. In general, lower numbers mean faster transitions and therefore fewer visible image artifacts such as ghosting. Grey to grey (GtG), measured in milliseconds (ms).

On two-dimensional display devices such as computer monitors the display size or view able image size is the actual amount of screen space that is available to display a picture, video or working space, without obstruction from the bezel or other aspects of the unit"s design. The main measurements for display devices are: width, height, total area and the diagonal.

The size of a display is usually given by manufacturers diagonally, i.e. as the distance between two opposite screen corners. This method of measurement is inherited from the method used for the first generation of CRT television, when picture tubes with circular faces were in common use. Being circular, it was the external diameter of the glass envelope that described their size. Since these circular tubes were used to display rectangular images, the diagonal measurement of the rectangular image was smaller than the diameter of the tube"s face (due to the thickness of the glass). This method continued even when cathode-ray tubes were manufactured as rounded rectangles; it had the advantage of being a single number specifying the size, and was not confusing when the aspect ratio was universally 4:3.

With the introduction of flat panel technology, the diagonal measurement became the actual diagonal of the visible display. This meant that an eighteen-inch LCD had a larger viewable area than an eighteen-inch cathode-ray tube.

Estimation of monitor size by the distance between opposite corners does not take into account the display aspect ratio, so that for example a 16:9 21-inch (53 cm) widescreen display has less area, than a 21-inch (53 cm) 4:3 screen. The 4:3 screen has dimensions of 16.8 in × 12.6 in (43 cm × 32 cm) and area 211 sq in (1,360 cm2), while the widescreen is 18.3 in × 10.3 in (46 cm × 26 cm), 188 sq in (1,210 cm2).

Until about 2003, most computer monitors had a 4:3 aspect ratio and some had 5:4. Between 2003 and 2006, monitors with 16:9 and mostly 16:10 (8:5) aspect ratios became commonly available, first in laptops and later also in standalone monitors. Reasons for this transition included productive uses (i.e. besides Field of view in video games and movie viewing) such as the word processor display of two standard letter pages side by side, as well as CAD displays of large-size drawings and application menus at the same time.LCD monitors and the same year 16:10 was the mainstream standard for laptops and notebook computers.

In 2010, the computer industry started to move over from 16:10 to 16:9 because 16:9 was chosen to be the standard high-definition television display size, and because they were cheaper to manufacture.

In 2011, non-widescreen displays with 4:3 aspect ratios were only being manufactured in small quantities. According to Samsung, this was because the "Demand for the old "Square monitors" has decreased rapidly over the last couple of years," and "I predict that by the end of 2011, production on all 4:3 or similar panels will be halted due to a lack of demand."

The resolution for computer monitors has increased over time. From 280 × 192 during the late 1970s, to 1024 × 768 during the late 1990s. Since 2009, the most commonly sold resolution for computer monitors is 1920 × 1080, shared with the 1080p of HDTV.2560 × 1600 at 30 in (76 cm), excluding niche professional monitors. By 2015 most major display manufacturers had released 3840 × 2160 (4K UHD) displays, and the first 7680 × 4320 (8K) monitors had begun shipping.

Every RGB monitor has its own color gamut, bounded in chromaticity by a color triangle. Some of these triangles are smaller than the sRGB triangle, some are larger. Colors are typically encoded by 8 bits per primary color. The RGB value [255, 0, 0] represents red, but slightly different colors in different color spaces such as Adobe RGB and sRGB. Displaying sRGB-encoded data on wide-gamut devices can give an unrealistic result.Exif metadata in the picture. As long as the monitor gamut is wider than the color space gamut, correct display is possible, if the monitor is calibrated. A picture which uses colors that are outside the sRGB color space will display on an sRGB color space monitor with limitations.Color management is needed both in electronic publishing (via the Internet for display in browsers) and in desktop publishing targeted to print.

Most modern monitors will switch to a power-saving mode if no video-input signal is received. This allows modern operating systems to turn off a monitor after a specified period of inactivity. This also extends the monitor"s service life. Some monitors will also switch themselves off after a time period on standby.

Most modern laptops provide a method of screen dimming after periods of inactivity or when the battery is in use. This extends battery life and reduces wear.

Most modern monitors have two different indicator light colors wherein if video-input signal was detected, the indicator light is green and when the monitor is in power-saving mode, the screen is black and the indicator light is orange. Some monitors have different indicator light colors and some monitors have blinking indicator light when in power-saving mode.

Many monitors have other accessories (or connections for them) integrated. This places standard ports within easy reach and eliminates the need for another separate hub, camera, microphone, or set of speakers. These monitors have advanced microprocessors which contain codec information, Windows interface drivers and other small software which help in proper functioning of these functions.

Monitors that feature an aspect ratio greater than 2:1 (for instance, 21:9 or 32:9, as opposed to the more common 16:9, which resolves to 1.77:1).Monitors with an aspect ratio greater than 3:1 are marketed as super ultrawide monitors. These are typically massive curved screens intended to replace a multi-monitor deployment.

These monitors use touching of the screen as an input method. Items can be selected or moved with a finger, and finger gestures may be used to convey commands. The screen will need frequent cleaning due to image degradation from fingerprints.

Some displays, especially newer flat panel monitors, replace the traditional anti-glare matte finish with a glossy one. This increases color saturation and sharpness but reflections from lights and windows are more visible. Anti-reflective coatings are sometimes applied to help reduce reflections, although this only partly mitigates the problem.

Most often using nominally flat-panel display technology such as LCD or OLED, a concave rather than convex curve is imparted, reducing geometric distortion, especially in extremely large and wide seamless desktop monitors intended for close viewing range.

Newer monitors are able to display a different image for each eye, often with the help of special glasses and polarizers, giving the perception of depth. An autostereoscopic screen can generate 3D images without headgear.

A combination of a monitor with a graphics tablet. Such devices are typically unresponsive to touch without the use of one or more special tools" pressure. Newer models however are now able to detect touch from any pressure and often have the ability to detect tool tilt and rotation as well.

The option for using the display as a reference monitor; these calibration features can give an advanced color management control for take a near-perfect image.

Raw monitors are raw framed LCD monitors, to install a monitor on a not so common place, ie, on the car door or you need it in the trunk. It is usually paired with a power adapter to have a versatile monitor for home or commercial use.

A desktop monitor is typically provided with a stand from the manufacturer which lifts the monitor up to a more ergonomic viewing height. The stand may be attached to the monitor using a proprietary method or may use, or be adaptable to, a VESA mount. A VESA standard mount allows the monitor to be used with more after-market stands if the original stand is removed. Stands may be fixed or offer a variety of features such as height adjustment, horizontal swivel, and landscape or portrait screen orientation.

The Flat Display Mounting Interface (FDMI), also known as VESA Mounting Interface Standard (MIS) or colloquially as a VESA mount, is a family of standards defined by the Video Electronics Standards Association for mounting flat panel displays to stands or wall mounts.

A fixed rack mount monitor is mounted directly to the rack with the flat-panel or CRT visible at all times. The height of the unit is measured in rack units (RU) and 8U or 9U are most common to fit 17-inch or 19-inch screens. The front sides of the unit are provided with flanges to mount to the rack, providing appropriately spaced holes or slots for the rack mounting screws. A 19-inch diagonal screen is the largest size that will fit within the rails of a 19-inch rack. Larger flat-panels may be accommodated but are "mount-on-rack" and extend forward of the rack. There are smaller display units, typically used in broadcast environments, which fit multiple smaller screens side by side into one rack mount.

A stowable rack mount monitor is 1U, 2U or 3U high and is mounted on rack slides allowing the display to be folded down and the unit slid into the rack for storage as a drawer. The flat display is visible only when pulled out of the rack and deployed. These units may include only a display or may be equipped with a keyboard creating a KVM (Keyboard Video Monitor). Most common are systems with a single LCD but there are systems providing two or three displays in a single rack mount system.

A panel mount computer monitor is intended for mounting into a flat surface with the front of the display unit protruding just slightly. They may also be mounted to the rear of the panel. A flange is provided around the screen, sides, top and bottom, to allow mounting. This contrasts with a rack mount display where the flanges are only on the sides. The flanges will be provided with holes for thru-bolts or may have studs welded to the rear surface to secure the unit in the hole in the panel. Often a gasket is provided to provide a water-tight seal to the panel and the front of the screen will be sealed to the back of the front panel to prevent water and dirt contamination.

An open frame monitor provides the display and enough supporting structure to hold associated electronics and to minimally support the display. Provision will be made for attaching the unit to some external structure for support and protection. Open frame monitors are intended to be built into some other piece of equipment providing its own case. An arcade video game would be a good example with the display mounted inside the cabinet. There is usually an open frame display inside all end-use displays with the end-use display simply providing an attractive protective enclosure. Some rack mount monitor manufacturers will purchase desktop displays, take them apart, and discard the outer plastic parts, keeping the inner open-frame display for inclusion into their product.

According to an NSA document leaked to Der Spiegel, the NSA sometimes swaps the monitor cables on targeted computers with a bugged monitor cable in order to allow the NSA to remotely see what is being displayed on the targeted computer monitor.

Van Eck phreaking is the process of remotely displaying the contents of a CRT or LCD by detecting its electromagnetic emissions. It is named after Dutch computer researcher Wim van Eck, who in 1985 published the first paper on it, including proof of concept. Phreaking more generally is the process of exploiting telephone networks.

Masoud Ghodrati, Adam P. Morris, and Nicholas Seow Chiang Price (2015) The (un)suitability of modern liquid crystal displays (LCDs) for vision research. Frontiers in Psychology, 6:303.

When a PC suddenly goes on the fritz for no apparent reason, checking the PC power supply first may save a lot of time troubleshooting the system. A faulty PC power supply belies many intermittent computer problems. This is why experienced PC technicians often look first at the PSU when diagnosing PC hardware issues.

As with any troubleshooting situation, disconnect all but the necessary peripherals from the PC. Usually this means you’re left only with the mouse, keyboard and monitor connected.

Many power supplies have an external switch located at the rear of the unit. Check that it has not been accidentally been switched off. Plug the PSU power cable into a wall socket or surge protector, and turn on the computer. Most power supply models have a light on back of the unit that glows when it’s powered on. If it doesn’t light, try a different power cable and a different socket to eliminate those items as the source of the problem.

The paper clip test, alternatively called the jumper test, allows you to verify PSU functionality when it is disconnected from the components inside a PC. This test will identify some common issues:

Locate the 20+4P (24-pin) connector. Bend the paperclip and insert one end into the green pin (PS_ON) and the other into any of the black pins (Ground).

The paper clip test is a crude but effective way to confirm if your PSU needs to be replaced. It will not tell you much else. If your power supply passes the paper clip test, you still may need to identify related issues:

To perform more nuanced testing of your power supply, you will need to use or buy a multimeter. A multimeter is an instrument that measures electrical current, principally voltage (volts), current (amps), and resistance (ohms). If you’re an electronics technician, you probably have one already, and are definitely familiar with this tool.

If you’re working as an internal IT, it probably isn’t worth your time to get overly intensive with power supply testing and repair. The cost of a new PSU is relatively low, and does not justify extensive personnel hours dedicated to a complex diagnosis. It is common practice for departments that manage multiple PCs is to keep spare power supply or two on hand for “swap” testing to identify when a PSU is the root cause of recurring computer problems.

If your computers are under warranty and you suspect the power supply may be to blame, that’s when you would take advantage of manufacturer support and warranty for desktop computers that you purchase. If you’re buying your business computers as finished systems, it’s a better use of company resources for the manufacturer to troubleshoot faulty computer power supplies and other components, while your team gets to work on a freshly replaced PC.

PO Box, APO/FPO, Afghanistan, Alaska/Hawaii, Albania, Algeria, American Samoa, Andorra, Angola, Anguilla, Antigua and Barbuda, Argentina, Armenia, Aruba, Austria, Azerbaijan Republic, Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, British Virgin Islands, Brunei Darussalam, Bulgaria, Burkina Faso, Burundi, Cambodia, Cameroon, Canada, Cape Verde Islands, Cayman Islands, Central African Republic, Chad, Chile, China, Colombia, Comoros, Cook Islands, Costa Rica, Cyprus, Czech Republic, Côte d"Ivoire (Ivory Coast), Democratic Republic of the Congo, Denmark, Djibouti, Dominica, Dominican Republic, Ecuador, Egypt, El Salvador, Equatorial Guinea, Eritrea, Estonia, Ethiopia, Falkland Islands (Islas Malvinas), Fiji, Finland, France, French Guiana, French Polynesia, Gabon Republic, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Greenland, Grenada, Guadeloupe, Guam, Guatemala, Guernsey, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Indonesia, Iraq, Ireland, Israel, Italy, Jamaica, Japan, Jersey, Jordan, Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Libya, Liechtenstein, Lithuania, Luxembourg, Macau, Macedonia, Madagascar, Malawi, Malaysia, Maldives, Mali, Malta, Marshall Islands, Martinique, Mauritania, Mauritius, Mayotte, Mexico, Micronesia, Moldova, Monaco, Mongolia, Montenegro, Montserrat, Morocco, Mozambique, Namibia, Nauru, Nepal, Netherlands, Netherlands Antilles, New Caledonia, New Zealand, Nicaragua, Niger, Nigeria, Niue, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, Philippines, Poland, Portugal, Puerto Rico, Qatar, Republic of Croatia, Republic of the Congo, Reunion, Romania, Russian Federation, Rwanda, Saint Helena, Saint Kitts-Nevis, Saint Lucia, Saint Pierre and Miquelon, Saint Vincent and the Grenadines, San Marino, Saudi Arabia, Senegal, Serbia, Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, Suriname, Svalbard and Jan Mayen, Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania, Thailand, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Turks and Caicos Islands, Tuvalu, US Protectorates, Uganda, Ukraine, United Arab Emirates, United Kingdom, Uzbekistan, Vanuatu, Vatican City State, Venezuela, Vietnam, Virgin Islands (U.S.), Wallis and Futuna, Western Sahara, Western Samoa, Yemen, Zambia, Zimbabwe

To provide you more detailed instruction, you can also click ASUS Youtube video link below to know more about Troubleshooting for No display on LCD Monitor

Make sure if the operating system had entered hibernation,sleep or power-save mode. Press any key (Enter key / Power key) or move the mouse to wake it up.

Check if the signal cable (VGA / DVI / HDMI / DisplayPort) is wellconnected , and confirmed another end of the output cable has been firmly connected to computer input port (graphics card). Unplug and plug 2-terminals again to ensure all pins aren"t bent.

Check if the signal cable (VGA / DVI / HDMI / DisplayPort) is wellconnected and confirmed another end of the output cable has been firmly connected to computer input port (graphics card). Unplug and plug 2-terminals again to ensure all the pins aren"t bent.

If the model had attached with the power supply (AC-adapter), make sure the power supply has connected to the screen. Please check if the light of power supply is ON. If the light is NOT ON, change another power supply to test.

Are there any regional differences inpower specifications thatASUS LCD monitor supported (for example: If monitor was bought in Taiwan, can it be used in China or other countries?)

ASUS LCD monitor can support power specification: AC 100-240V. As long as within this voltage range, the display can work properly. However, please be noted that if you bought a monitor from another region, the power cord is not necessarily compatible to power outlet. Customer should replace the appropriate power cord or plug adapter in order to ensure normal power supply of the display.