i2c 1602 lcd module datasheet pricelist

ERMC1602SBS-2 is 16 characters wide,2 rows character lcd module,SPLC780C controller (Industry-standard HD44780 compatible controller),6800 4/8-bit parallel interface,single led backlight with white color included can be dimmed easily with a resistor or PWM,stn- blue lcd negative,white text on the blue color,wide operating temperature range,rohs compliant,built in character set supports English/Japanese text, see the SPLC780C datasheet for the full character set. It"s optional for pin header connection,5V or 3.3V power supply and I2C adapter board for arduino.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!".For 8051 microcontroller user,we prepared the detailed tutorial such as interfacing, demo code and Development Kit at the bottom of this page.

ERM1602SYG-6 is 16 characters wide,2 rows character lcd module,SPLC780C controller (Industry-standard HD44780 compatible controller),6800 4/8-bit parallel interface,single led backlight with yellow green color included can be dimmed easily with a resistor or PWM,stn-lcd positive,dark blue text on the yellow green color,wide operating temperature range,rohs compliant,built in character set supports English/Japanese text, see the SPLC780C datasheet for the full character set. It"s optional for pin header connection,5V or 3.3V power supply and I2C adapter board for arduino.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!".For 8051 microcontroller user,we prepared the detailed tutorial such as interfacing, demo code and Development Kit at the bottom of this page.

The CFA533-***-KC series is a 16x2 I2C LCD with keypad. The I2C interface allows you to use just two lines (SDA & SCL) to have bi-directional communication with the I2C LCD. Other devices can also share those two I2C control lines with the LCD. Only 4 wires are needed to connect this I2C LCD: power, ground, SDA (I2C Serial DAta) and SCL (I2C Serial CLock).

The CFA533 can run on 3.3v to 5.0v directly, with no changes needed, so you do not need to do any level translation between your embedded processor and the I2C LCD. Simply power the CFA533 from the same supply as your processor and the I2C signal levels will match up.

Using only one address on your I2C bus, you can add all the elements that you need for your front panel. The CFA533 I2C LCD can also read up to 32 DS18B20 digital temperature sensors, giving you an easy way to integrate temperature sensing over the I2C bus. No additional firmware or pins are needed on the host system.

This CFA533-TFH variant features crisp dark letters against a white, backlit background. The keypad has a matching white LED backlight. Since the LCD is a backlit positive FSTN, the CFA533-TFH I2C LCD is readable in direct sunlight, as well as complete darkness.

Whenever we work with embedded system we need a reliable output device with the help of which we get the required information, now this problem is solved with the introduction of 16 character by 2 (16x2) LCD. Uses like Alphanumeric output, Information Display, Process status, in short we can keep eye on every move of our microcontroller.This alphanumerics display can be easily interfaced with any host controller such as 8051 derivatives, PIC Series, AVR, ARM series of controllers or using development boards such as Arduino or Raspberry Pi. With this I2C interface LCD module, you only need 2 lines (I2C) to display the information.If you already have I2C devices in your project, this LCD module actually cost no more resources at all. The address can be set from 0x20-0x27. Fantastic for Arduino or gadgeteer based projects.

I2C Module has an inbuilt PCF8574 I2C chip that converts I2C serial data to parallel data for the LCD display. These modules are currently supplied with a default I2C address of either 0x27 or 0x3F. To determine which version you have check the black I2C adaptor board on the underside of the module. If there a 3 sets of pads labelled A0, A1, & A2 then the default address will be 0x3F. If there are no pads the default address will be 0x27. The module has a contrast adjustment pot on the underside of the display. This may require adjusting for the screen to display text correctly.

This Blue LCD display module has a high-speed I2C serial bus. With the limited pin resources, your project may be out of resources using normal LCD shields. The LCD display is a 2x16 character STN white display with a blue LED backlight. With the I2C interface LCD display, you only need 2 lines (I²C) to display the information. If you already have I²C devices in your project, this LCD module actually costs no more resources. Fantastic for an Arduino-based project.

This is another great IIC/I2C/TWI/SPI Serial Interface. As the pin resources of Arduino controller is limited, your project may be not able to use normal LCD shield after connected with a certain quantity of sensors or SD card. However, with this I2C interface module, you will be able to realize data display via only 2 wires. If you already has I2C devices in your project, this LCD module actually cost no more resources at all. It is fantastic for Arduino based project.

2004 LCD module displays 2 lines of 16 characters. It is ideal for electronics projects that have displayed more information. It can be used easily and in low light conditions because it has light and backlight.Backlight also need to be protected by resistance or potentiometer 2k. To reduce the pins that you will use to connect the LCD to the controller you can use an I2C module.

3. We add LCD_i2c library, wich you also find in "Downloads" and after you open one of library"s example and in change the adress with the one you found earlier and upload.

This is a great I2C Serial Interface. As the pin resources for Arduino controller is limited, your project may be not able to use normal LCD shield after connected with many sensors or interfaces. With this I2C interface module, you will be able to realize data display via only 2 wires. Fantastic for Arduino based project.

This is a RoHS compliant I2C Serial LCD Daughter board that can be connected to a standard 16×2 or 20×4 Character Display Module that supports 4-bit mode. All Character Modules sold on our site support 4-bit mode, and nearly all commercially available 16×2 and 20×4 line character modules support it too.

This board has a PCF8574 I2C chip that converts I2C serial data to parallel data for the LCD display. There are many examples on the internet for using this board with Arduino. Do a search for “Arduino LCD PCF8574“. The I2C address is 0x3F by default, but this can be changed via 3 solder jumpers provided on the board. This allows up to 3 LCD displays to be controlled via a single I2C bus (giving each one it’s own address)

Module with LCD display 16x2 characters with blue backlight. It is supplied with the voltage from 3.3 V to 5 V and communicates via the I2C interface. The display has adjustable backlight brightness and is controlled using a dedicated library. The Wiki page contains the manual and sample programs.