pedego lcd display for sale

When you turn on the Pedego display (which can be done by single pressing the power button), you come across your first screen. This is your main display. At the top of the screen, there is your speedometer. Immediately underneath is the battery charge. Underneath that, there is a trip meter, riding time, and odometer (they can be switched by single pressing the "set" button). To the left of the screen is the pedal assist level (which will always start at 0 and can be increased or decreased by pressing the plus and minus buttons).

Turn on your Pedego display by single pressing the power button. Press and hold the set button (underneath the power button) until it becomes backlit. There are different settings.

If your bike display is not on, single press the power button. Once you are on the main riding screen, single press the power button again. The screen will light up, and this will activate both your head and tailight.

Single press your power button to turn on the display. If there is a flashing error message next to the battery indicator, then you should call the Pedego Tech Support at 800-646-8604 or your local Pedego dealer. If you purchased your bike through Electric Bike Place or MACkite, please call 800-622-4655.

Turn on your display. To activate the USB port, press the "set" and plus button for 3 seconds until you see the USB icon. You can then remove the rubber cover and insert your USB cable into the bottom of your display.

Turn on your display. Press the "set" button until the screen is backlit. Press "set" until you reach level 6. When your indicator is set to "on", then your throttle will be unregulated. Press the plus or minus button to regulate your throttle output to walking speed. Hold the "set" button to save your changes.

Turn on the display. On your screen, you will notice a "BMS". Select Pedego models have battery communication. You can see your type of battery communication above the battery indicator.

Turn on the display. Press and hold the "set" button until it becomes backlit. Single press the "set" button two times. "Set 3" will be the wheel size. You can press the plus or minus button to increase or decrease your wheel size. To save, press and hold the "set" key.

Turn on the display. Press the "set" button until it becomes backlit. Next, single press the "set" button three times until you reach "Set 4". To change between MPH and KPH, single press the plus or minus key. Once you have chosen your preference, hold the "set" button to save your changes.

Pedego electric bikes are equipped with an LCD console that monitors your pedal assist level, speed, odometer, trip distance, riding time, and battery energy level. If you have purchased your electric bicycle from a Pedego dealer or via the official Pedego website, your ebike will arrive with all the correct LCD console settings, such as km/hr settings and a maximum motor speed of 32 km/hr. In this article, we list the different numbers and symbols, what they mean, and how to change certain settings on your electric bike.

It’s easy to turn the LCD console on. First, make sure the battery is fully inserted and the on/off switch is in the on or [I] position. Then press the power button (top button) on the four button selector located near the left grip on the handlebars. To turn off the LCD screen completely, press and hold the power button for three seconds. The console will also automatically turn off after five minutes of bike inactivity.

Pedal Assist Number: The large number on the left of your screen. The higher the number, the more energy the motor is exerting to propel you forward while you pedal. On most Pedego bikes there are 6 levels of pedal assist. In Level 0 the motor will not be activated by either throttle or pedal assist for most Pedegos. Levels 1-5 give you increasing levels of power (and top motor-assisted speed) while pedalling. Note that in these levels, the throttle acts as an override and can be activated to increase the power temporarily up to the maximum km/hr speed as required. Level 6 is a throttle-only setting and pedalling does not activate the motor. Pedal assist power can be adjusted while riding: simply hit the plus [+] button to increase power or the minus [-] button to decrease the amount of power the electric motor is applying to the wheel when you are pedalling.

To turn on the screen’s backlight as well as the integrated front and rear lights on your Pedego, once the LCD screen is on, simply press the power button and the lights will come on. Press it once again to turn them off. (Pressing the power button for longer than three seconds will turn the entire LCD unit off.)

There are other functions your LCD console can perform. By pressing and holding the “SET” button for a couple of seconds, located just below the power button, you’ll enter the programming menus. Here are the explanations for each screen and how they function.

After you’ve powered on the LCD screen, hold the “SET” button for two seconds. The screen will become backlit and you can release the button. You’ll see the number 1 in the bottom left corner. You’ll also see the trip odometer figure and here is where you can reset it back to zero by simply pressing the minus [-] button. This is useful to determine how long a particular ride is or how much battery power is used over a particular distance. To reset the trip odometer to zero, hold “SET” again for two seconds to exit the setup interface.

This should have been set when you purchased the bike. After powering on the LCD screen, hold the “SET” button for two seconds. The screen will become backlit (release the button at this point) and you’ll see the number 1 in the bottom left corner. Press the set button twice, and you’ll see a number 3 in the bottom left corner. If your electric bike has 28-inch tires, the number on this screen will read 28. You can toggle between all the sizes by pressing the minus [-] button. Hold “SET” again for two seconds to exit the setup interface.

Again, if your electric bike was purchased in Canada, the LCD console will already be set to kilometres per hour. To change between MPH and KPH, power on the LCD screen and hold the “SET” button for two seconds. The screen will become backlit (release the button at this point) and you’ll see the number 1 in the bottom left corner. Press the set button three times and you’ll see a number 4 in the bottom left corner. To toggle between MPH and KPH, press the plus [+] or minus [-] button. You can also use this function to determine whether you’re eligible to receive Mile Marker pins. (Check about this with your local Pedego store!) Hold “SET” again for two seconds to exit the setup interface.

To engage the pedal assist limiter, or to turn it off, power on the LCD screen and hold the “SET” button for two seconds. The screen will become backlit (release the button at this point). Press the set button four times, and you’ll see a number 5 in the bottom left corner. When the pedal assist limiter is set to “OFF,” you’ll have a reduced top speed through all pedal assist modes. Toggle between “OFF” and “ON” by pressing the plus [+] or minus [-] buttons. Hold “SET” again for two seconds to exit the setup interface.

To engage the throttle limiter, or to turn it off, power on the LCD screen and hold the “SET” button for two seconds. The screen will become backlit (release the button at this point). Press the set button five times, and you’ll see a number 6 in the bottom left corner. When the throttle limiter is set to “OFF,” you’ll have a regulated throttle output to about walking speed. Toggle between “OFF” and “ON” by pressing the plus [+] or minus [-] buttons. Hold “SET” again for two seconds to exit the setup interface.

The LCD console also has a USB port embedded in the underside of the LCD console that allows you to charge your mobile devices. To activate the USB charger, press the plus [+] button and the SET button at the same time for 2 seconds. This will turn on the USB charging capability. Hold the same buttons again for 2 seconds to turn this feature off.

Error Code #15 is the communication between the LCD panel to the speed controller, according to Pedego chart. Just be sure to double-check the cable to the