lcd screen computer case free sample

I saw a really cool video of a PC case called "Snowblind", that had a transparent LCD Screen as a side panel. I was amazed over how cool it was. The only problem was that it was really expensive. Therefore, I tried making my own! In this instructables I will go through how I made it, and how you could make your own. The best of all, since it was made from an old monitor that was thrown away, it was basically free! I just added some LED strips on the inside of the case to get better contrast on the screen. You could probably re-use the monitors backlight, but it"s safer and easier to just get some cheap LED strips.

You will have to reverse engineer the controller to find the power connections, and solder a new power connector on. This way, you can use the ATX power supply that powers your computer. I used a multimeter, where I had one probe to the ground plane (For example around the mounting screws), and used the other probe to search for 5V or 12V power on the pins coming from the power supply.

First, remove the frame of the panel. It is fixed with clips, so just bend the frame a little and lift the frame up. Next, separate the front LCD from the backlight. For the next step, you will have to be careful. This step involves removing the anti glare film. It is glued to the panel, and therefore it"s easy to break the LCD when trying to remove it.

Then you are done modding the LCD! Now, you can hook it up to the panel and test it. Just be careful with the ribbon cables going from the LCD PCB to the panel.

The side panel of this case fits the LCD perfectly. Just line it up to the side facing the back, and to the top, and use some tape to tape it to the glass. Then, use some vinyl on the outside where the LCD is not covering the glass.

It"s really important to have lots of lights inside the case, to make it easier to see the LCD. Therefore, try to fill the case with even more LED strips.

You are now ready to assemble everything. In this case, the controller fit nicely in the hard drive compartment, so I glued it there and fed the ribbon cable through the hole in the inside of the case. That way it was pretty much hidden inside the case.

Now you can carefully mount the side panel back on the computer. You might have to drill a new hole for the thumb screw in the back to make it fit properly.

You can now power up the computer, open the screen settings and set it up for dual screens. You might have to flip the display 180 degrees too. When you have done that, open Wallpaper Engine and set a wallpaper of choice!

I have the same problem, I have read on google that the lcd could also be 3,3v (check if you have 3.3v lanes) so i will be trying to solder a sata cable to it because it comes with 3,3 and 5v connectors but the im not sure if save to use sata cables0

Hey I have a little question, I also have a Dell 1905FP, but I think it"s an older model because I don"t have a ribbon cable but a normal cable with a plug. My problem is that I have peeled off one film but it still looks like there is a second film on the back because it is still a little blurry. But I"m afraid that if I try to pull them off, my LCD display will break. Maybe you have an idea. Thanks in advance

Really neat. I saw the same snowblind case and wanted it but too expensive. I also saw someone who made their own using a USB monitor. But I like your setup better.2

Terrific job! May I ask why you would need to remove the front polarizer? If my understanding is correct, both the front and back polarizers are needed in order for the LCD to work properly (i.e., the light gets polarized by the back polarizer first, and then passes through the front polarizer)? You comments will be appreciated!

Hey, great work on this project. I wanted to buy the snowbind case but couldn"t justify the cost. I have the same case and I ended up picking up the same monitor that you used in your project.

Is it possible that you post or send me photos of the inside of the case when you have this installed? I"m just a bit confused on how you wired up everything?

I tried taking some photos, but I have covered the screen PCB with a cover, so it was hard to see in the photos. I basically just laid it inside the case with a 90-degree angle. I tried drawing it here: (view from the front)0

I used "wallpaper engine" to just set the animations as wallpaper on that screen. I mentioned it in the last step, but I could probably make a own step about that, if you are interested in more details.2

I think you should have more pics and info about the re- mounting the LCD. After all if you don"t do it right all that work is for nothing. While I understand your wiring diagram, I think that it should be explained and a larger part of this Instructible...for example to get white lite your are powering all 3 lanes (red,green,blue) on the RGB tape.

Hello, Wonderfull project, I have the same case and I would love to do it (if I have time and the screen to the right size). Just a question, can you put a photo of the cable connection to see if it"s easy to open the case ? One little suggestion, instead of connecting the panel to the graphic card (which mean to run a cable outside, why don"t you use a USB to VGA or DVI converter (like this https://www.amazon.fr/Adaptateur-convertisseur-adaptateur-Affichage-multi-écrans/dp/B079L81FRD/ref=asc_df_B079L81FRD/?tag=googshopfr-21&linkCode=df0&hvadid=227894524041&hvpos=&hvnetw=g&hvrand=17927658121409960098&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9055710&hvtargid=pla-442905712462&psc=1) ?More CommentsPost Comment

The Hyte Y60 is one of the best PC cases on the market, and it’s getting a big upgrade in the form of an official DIY mod kit. TheHyte Y60 LCD DIT kit is available now for $120, allowing you to replace one of the tempered glass panels of the case with a programable screen.

If you frequent PC builds on Reddit or Instagram, you’ve probably seen this mod before. For months, community members have bought screens that fit in the gap in Hyte’s case and used community 3D-printed mounts to attach them. In a Reddit thread several months back, in fact, the company responded to a user’s build with “THIS IS SO COOL.”

Hyte is now selling the kit in an official capacity. The $120 kit includes the screen, a driver board to deliver power and data to the screen, and the cables to hook everything up. Unfortunately, it’s not an all-in-one solution out of the box. You still need to 3D-print a mount for the screen, but Hyte includes the file you need to print.

The screen comes with a resolution of 1920 x 515, and it’s not something you can control through software. Instead, the included driver board includes a mini HDMI connection that you’ll need to route through your PC and connect to your graphics card. After that, the panel will show up as another monitor in your operating system.

The LCD kit was among Hyte’s CES 2023 announcements. The company also announced the new Hyte Y40 case, which is a slimmed-down version of the wildly popular Y60. Instead of the dual-chamber design of the Y60 and fish tank-like look, the Y40 opts for a traditional power supply basement and a slimmer form factor.

Although it’s smaller overall, the Y40 actually has more space for your graphics card, which could make a big difference with GPUs like the RTX 4090. The vertical GPU mount includes four slots as opposed to the three slots on the Y60. The case is also $50 cheaper, clocking in at $150.

Case modding took off in the late 90s, and taught us all that computers could (and should!) look awesome. Much of the aesthetic went mainstream, and now tons of computer cases come with lights and windows and all the rest. [WysWyg_Protogen] realized those simple case windows could be way cooler with a neat LCD hack, and set to work.

The concept is simple. Take an old LCD monitor, remove the backlight and extraneous hardware, and then install it to the window in a computer case. When lit from behind via LEDs in the case, the screen creates a ghostly display through which the computer’s internals can still partially be seen. It’s a really compelling effect, and in theory, quite easy to achieve. All one need do is mount the stripped-down screen to the case and pipe it video from the graphics card.

In practice, it’s a little tricky. Disassembling the screen and removing things like the anti-glare coating can be tough to do without damaging the delicate panel inside. The windows typically used on computer cases can dull the effect, too. However, [WysWyg_Protogen] is continuing to tinker with the project and the results are getting increasingly impressive with each iteration. It doesn’t photograph too well, but it looks truly amazing in motion.

We often forget LCDs are transparent in their basic form, as we generally only use them with backlights or reflective backers. They really do look great when used in this transmissive way, though. Video after the break.

Actually beside myself right now. How does this look this good? This was a trash pile monitor and this looks like a 700 dollar case upgrade pic.twitter.com/4yBXlcY921

Hi everybody! Bill Owen from Mnpctech. I hope you"re having a great day! Several people have asked if I could share the steps on how I do my Touchscreen LCD mod in PC Computer case bezels, and you’ve come to the right video!

I’ve been using this Amazon 5 Inch Capacitive Touch Screens for $52.99 delivered on Amazon Prime, I’ll posted a link in Video description. The kit comes a with Micro USB for power and HDMI video connector, but these cables are too short for these PC case mods. It includes M3 stand-offs, a Driver Disc and some Instructions. It’s a 5 point Capacitive Touch screen with a Resolution of 800 x 460, which is just fine for it’s 5” viewing screen In addition to the LCD touchscreen, I will buy the following cables for my Desktop Custom PC LCD Case Mod.

One 3ft “Right Angle” 270 degree HDMI cord, 6” 90 Degree Angle HDMI Extension Adapter, and 3ft USB Male to Micro B power connector. For Mounting the LCD Touchscreen Panel, I use 3/16” thick Black acrylic to make custom mounting brackets for the LCD touch screen.

You can PAUSE the video on this page to record the measurements that I’ve made for cutting the acrylic. This PC Case Mod is very easy. "The reason I’m making brackets for my desktop PC LCD Monitor Mod?" I want the ability to easily install or remove the Touchscreen with thumbscrews. I’m using 1/8” drill bit for acrylic, and 6/32 thread tap, These Black thumbscrews from Mnpctech.com. I’ll use the 1/8” drill bit to increase the diameter of the holes in the LCD pcb frame.

I discovered these drill bits for plastic several years ago, Notice the bit isn’t splintering or cracking the acrylic as I make the holes. Mnpctech stocks a variety of these drills bits. My mod requires Twelve 6/32 washers, and links posted in description, “Why so many washers?” We want the Touchscreen to mount flush on the backside of the bezel, I also don’t want to apply any unnecessary pressure to the screen or the PCB, See how this sheet of paper easily slides under the screen Next stage is cutting the hole in the bezel, The best PC case for this mod is the ones without optical drive bays, which every popular case manufacturer now offers.

If you’re using an older case with 5.25 drive bays, you could attach a mounting plate with 5” opening that covers THREE 5.25 bays. That’s how we did this mod in the early days of PC Modding. Determine and measure out a location in the center of your bezel, you can also mount the LCD vertically if you prefer, and just change the screen orientation in Windows. Since the bezel is plastic, I’m using a Dremel with 1.5” reinforced cut off wheel, Don’t forget to always wear eye protection when using power tools. Oops, WTH? Hahaha After cutting our 5” diagonal square hole, I’ll hand file the edges so everything is precise and clean. You may have to remove sound insulation foam from backside of your bezel, I’m using E6000 adhesive to attach the two mounting brackets. This adhesive is very GOOEY at first, so consider masking off the screen, to prevent getting any of this on it. I like that it’s tacky for couple of minutes, so I have time to position the LCD in place, and then I’ll temporarily tape it in place while it cures overnight.

Mounting your Touchscreen LCD in the PC this way allows you to easily remove and re-install the LCD at any time. Especially if you ever need to replace it for some reason. Let’s get this LCD touchscreen connected to the PC, all of the cables are routed from the front to thee rear PCI slots. *3ft “Right Angle” 270 degree HDMI cord *6” 90 Degree Angle HDMI Extension Adapter cable, I plug this compact cable into the Touchscreen to save space. *3ft USB Male to Micro B power connector This mod is great if you want an extra screen for monitoring your hardware and temps. You can also display Weather or calendar or email notifications,

Check out http://www.Rainmeter.net this community offers several hundred custom mad graphic interfaces for FREE, and you can configure your screen to display a variety of updated information tasks Thanks for watching! And Again, all of the products used in this PC case mod are listed in the video description.

See what your computer is up to, from processor load to bandwidth consumption. Monitor how running applications are making use of your gaming PC. Quickly track down any issues to ensure optimal performance.

Match your computer to how you use it, any time of day or night. CAM will make it so lights and cooling devices will help bring you more into the game than ever before.Contribute to CAM

Don’t think cleaning your computer is important? Think again. Your keyboard alone could be hosting more bacteria than a toilet seat – 400 times more, in fact.

While you should always check your computer manufacturer’s specific cleaning and disinfecting directions, in general, these tips will help you keep your PC and laptop surfaces germ-free.

DON’T spray a cleaning agent directly on your computer’s surface. Spray your cleaner onto a cloth first and then gently wipe the cloth over the surface.

Accidental Damage is any damage due to an unintentional act that is not the direct result of a manufacturing defect or failure. Accidental damage is not covered under the standard warranty of the product. Such damage is often the result of a drop or an impact on the LCD screen or any other part of the product which may render the device non-functional. Such types of damage are only covered under an Accidental Damage service offering which is an optional add-on to the basic warranty of the product. Accidental Damage must not be confused with an occasional dead or stuck pixel on the LCD panel. For more information about dead or stuck pixels, see the Dell Display Pixel Guidelines.

No, accidental damage is covered for Dell computers or monitors which are covered under the Accidental Damage Service offering for that specific product.

The LCD glass on the display is manufactured to rigorous specifications and standards and will not typically crack or break on its own under normal use. In general, cracked, or broken glass is considered accidental damage and is not covered under the standard warranty.

Internal cracks typically occur due to excessive force on the screen. This can be the result of some object hitting the screen, a drop, attempting to close the lid while an object is on the keypad area, or even holding the laptop by its screen.

Spots typically occur due to an external force hitting the screen causing damage to the LCD panel"s backlight assembly. While the top layer did not crack or break, the underlying area was compressed and damaged causing this effect.

If your Dell laptop LCD panel has any accidental damage but the laptop is not covered by the Accidental Damage service offering, contact Dell Technical Support for repair options.