sainsmart 1.8 tft lcd raspberry pi pricelist

The 1.8" TFT LCD SPI-bus display modules available from Adafruit and SainSmart are functionally equivalent, except that the SainSmart unit can be driven at a much faster SPI bus rate than the Adafruit (32 MHz vs. 4 MHz in my testing). Fabien Royer has shown that this is due to a slow level shifter in the Adafruit unit.

The original st7735fb kernel driver was by Matt Porter, and was enhanced by Lady Ada, Neil Greatorex, and myself. I started with Neil"s proposed version of Matt"s st7735fb driver, which I extracted from Lady Ada"s raspberrypi kernel repo. I applied Neil"s version to the current raspberrypi 3.2.27+ kernel, then I made multiple enhancements to the st7735fb driver (and fixed a glitch in the bcm2708 SPI driver). I"ve since collaborated with Neil to develop further enhancements, and ported the driver to the upcoming 3.6.y Raspberry Pi kernel.

* My version of the st7735fb_map driver allows either CE0 (SPI 0.0) or CE1 (SPI 0.1) to be configured. ** My version allows the configuration of any GPIO pin for D/C and RESET. *** Since I"m not using the MicroSD card device on the back of the display modules, the remaining pins are left unconnected.

Clone my raspberrypi-linux repo, then select either the 3.2.27-based branch or the 3.6.y-based branch (run "uname -a" on your Pi if you"re not sure which you need):

The board supports multiple different 1.8" panel pinouts including Adafruit and SainSmart, and sports mounting pads for three GPIO buttons. Very nice!

3.5inch RPi LCD (A) and 3.5inch RPi LCD (B) are hardware compatible with each other (uses different driver), and can be mutually substituted in most cases. (A) for low cost ver. while (B) for IPS ver. with better displaying.

Self collection avaliable at Oxley Bizhub, 71 Ubi Rd 1 #10-47 Singapore 408732 (To wait for confirmation before collection - Appointment required). Additional charge of $10 apply for delivery by courier in Singapore, FREE shipping for orders above $60.

We ship internationally too through Air Courier or Registered Mail (select on Checkout), do contact us for larger orders. All shipping taxes after shipment will be borne by customer for overseas orders.

This ST7735S 1.8" TFT Display features a resolution of 128×160 and SPI (4-wire) communication. Integrated with an SD card slot, it allows you to easily read full-color bitmaps from the SD card.

The module provides users with two wiring methods: pin header wiring and GDI (General Display interface). You can directly connect the display to a FireBeetle main controller using an FPC cable. Plug and play, easy to wire. Besides, the display supports a low refresh rate and offers a good display effect and strong versatility.

This is a short Application Note about how to use ST7735R Controller based TFT screen with RaspberryPi Universal Expansion Boardand RaspberryPi. More information about the screen can be found in the list of my Peripheral Boards.

I"m trying to output some data from a python script to a Sainsmart 1.8 TFT display. Followed the instructions from https://github.com/notro/fbtft/wiki, I am able to show the raspberry"s screen on the tft display with

When I try to output data from my python script, a pygame window ("pop up"-like) opens, but not on the tft screen, but on the main screen connected to the Raspberry with HDMI.

40 characters by 2 lines text display with font size 5x7 dots or 5x8 dots and cursor line. I2C, SPI or RS232/TTL serial interface. SPLC780D, SPLC782A,S6A0069, S6A0070, KS0066, KS0070B, NT7603H,NT7065, NT7066, ST7032 or equivalence controller driver. Contrast and brightness can be controlled by software. Positive/Neagtive, Transflective/Transmissive, Blue/Grey/Yellow-Green, W/O backlight, color of backlight and other options can be chosen.