adafruit ntsc pal television tft display 1.5 diagonal factory

Add some jazz & pizazz to your project with a color capactive touchscreen LCD. This TFT display is big (2.8" diagonal) bright (4 white-LED backlight) and colorful! 240x320 pixels with individual RGB pixel control, this has ...

Add some jazz & pizazz to your project with a color touchscreen LCD. This TFT display is big (2.8" diagonal) bright (4 white-LED backlight) and colorful! 240x320 pixels with individual RGB pixel control, this has way more resolution than a bl...

Add some sizzle to your Arduino project with a beautiful large touchscreen display shield with built in microSD card connection and a capacitive touchscreen. This TFT display is big (2.8" diagonal) bright (4 white-LED ba...

This breakout has 4 BSS138 FETs with 10K pullups. It works down to 1.8V on the low side, and up to 10V on the high side. The 10K"s do make the interface a little more sluggish than using a TXB0108 or 74LVC245 so Adafruit suggest checking those ou...

What"s better than a single LED? Lots of LEDs! A fun way to make a small display is to use an 8x8 matrix or a 4-digit 7-segment display. Matrices like these are "multiplexed" - so to control all the seven-segment LEDs you need...

For all of you out there who want to control 12 channels of PWM, adafruit salute you! Adafruit also would like you to check out this breakout board for the TLC59711 PWM driver chip. This chip can control 12 separate channels of 16-...

Adafruit 128x64 OLE is a compact display with buttons and a joystick. The Adafruit 128x64 OLED Bonnet for Raspberry Pi is the big sister to Adafruit"s mini PiOLED add-on. This version has 128x64 pixels (instead of 128x32) and a much larger s...

For years we"ve seen all sorts of microcontroller-friendly WiFi modules but none of them were really Adafruit-worthy. Either they were too slow, or too difficult to use, or required signing an NDA, or had limited functionality, or too expensive, ...

Feather is the new development board from Adafruit, and like its namesake it is thin, light, and lets you fly! Adafruit designed Feather to be a new standard for portable microcontroller cores.

Feather is the new development board from Adafruit, and like its namesake it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores.

Feather is the new development board from Adafruit, and like its namesake it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores.

Feather is the new development board from Adafruit, and like its namesake it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores.

Feather is the new development board from Adafruit, and like its namesake it is thin, light, and lets you fly! Adafruit designed Feather to be a new standard for portable microcontroller cores.

Feather is the new development board from Adafruit, and like its namesake it is thin, light, and lets you fly! Adafruit designed Feather to be a new standard for portable microcontroller cores.

Feather is the new development board from Adafruit, and like its namesake it is thin, light, and lets you fly! Adafruit designed Feather to be a new standard for portable microcontroller cores. This is the Adafruit Feather M0 WiFi ...

Ring, Ring! Who"s that callin"? It"s your breadboard! Introducing Adafruit FONA MiniGSM, an adorable all-in-one cellular phone module that lets you add voice, text, SMS and data to your project in an adorable lit...

Build your own cellular project and get off the grid with FONA. This pack comes with an uFL-antenna type FONA and paired with hand-picked accessories. It"s the Adafruit FONA - uFL Starter Pack.

For those who want to take it to the next level adafruit now have a 3G Cellular Modem breakout! The FONA 3G has better coverage, GSM backwards-compatibility and even sports a built-in GPS module for geolocation & asset t...

For those who want to take it to the next level adafruit now have a 3G Cellular Modem breakout! The FONA 3G has better coverage, GSM backwards-compatibility and even sports a built-in GPS module for geolocation & asset t...

Ring, Ring! Who"s that callin"? It"s your Arduino! Introducing Adafruit FONA 800 Shield, an adorable all-in-one cellular phone shield that lets you add voice, text, SMS and data to your project in an easy to use ...

Cellular + GPS tracking, all in one? Oh yes! Introducing Adafruit FONA 808 MiniGSM + GPS, an all-in-one cellular phone module with that lets you add location-tracking, voice, text, SMS and data to your project in an adorable little...

Cellular + GPS tracking, all in one, for your Arduino? Oh yes! Introducing Adafruit FONA 808 GSM + GPS Shield, an all-in-one cellular phone module with that lets you add location-tracking, voice, text, SMS and data to your p...

Wouldn"t it be cool to drive a tiny OLED display, read a color sensor, or even just flash some LEDs directly from your computer? Sure you can program an Arduino or Trinket to talk to these devices and your computer, but w...

It"s the exact same size as a Raspberry Pi Zero but works with any and all Raspberry Pi computers with a 2x20 connector - A+, B+, Zero, Pi 2, Pi 3, etc. On Adafruit tested it out with Raspbian (the official operating system) and Retropie.

Adafruit sure love the ATmega328 here at Adafruit, and we use them a lot for our own projects. The processor has plenty of GPIO, Analog inputs, hardware UART SPI and I2C, timers and PWM galore - just enough for most simple p...

Adafruit sure love the ATmega328 here at Adafruit, and adafruit use them a lot for our own projects. The processor has plenty of GPIO, Analog inputs, hardware UART SPI and I2C, timers and PWM galore - just enough for most si...

Adafruit sure love the ATmega328 here at Adafruit, and we use them a lot for our own projects. The processor has plenty of GPIO, Analog inputs, hardware UART SPI and I2C, timers and PWM galore - just enough for most simple p...

The original Adafruit Motorshield kit is one of Adafruit most beloved kits, which is why Adafruit decided to make something even better. Adafruit have upgraded the shield kit to make the bestest, easiest way to drive DC and Stepper moto...

Bend all audio files to your will with the Adafruit Music Maker shield for Arduino! This powerful shield features the VS1053, an encoding/decoding (codec) chip that can decode a wide variety of audio formats such as MP3, AAC...

Bend all audio files to your will with the Adafruit Music Maker shield for Arduino! This powerful shield features the VS1053, an encoding/decoding (codec) chip that can decode a wide variety of audio formats such as MP3, AAC...

The T-Cobbler Plus is an add on prototyping board from Adafruit specifically designed for the B+ that can break out all those tasty power, GPIO, I2C and SPI pins from the 40-pin header onto a solderless breadboard. This set will make "cobb...

Adafruit"ve taken our popular Adafruit PN532 breakout board and turned it into a shield - the perfect tool for any 13.56MHz RFID or NFC application. The Adafruit NFC shield uses the PN532 chip-set (the most popular NFC c...

The Pro Trinket PCB measures only 1.5" x 0.7" x 0.2" (without headers) but packs the same capability as an Arduino UNO. So it"s great once you"ve finished up a prototype on an official Arduino UNO ...

The Adafruit Push-button Power Switch is a tidy little design that lets you control a DC power source using an everyday tactile button. The breakout uses a latching analog circuit that is triggered by a push of the button. Press on...

You can now create a dazzling display with your Raspberry Pi Model A+/B+/Pi 2 with the Adafruit RGB Matrix HAT. This HAT plugs into your Pi and makes it super easy to control RGB matrices and create a colorful scrolling display or mini LED wall with ...

Sensiron Temperature/Humidity sensors are some of the finest & highest-accuracy devices you can get. And, finally adafruit have some that have a true I2C interface for easy reading. The SHT31-D sensor has an excellent ±2% relat...

Never hunt around for another crystal again, with the Si5351A clock generator breakout from Adafruit! This chip has a precision 25MHz crystal reference and internal PLL and dividers so it can generate just about any frequency, from

Listen to this good news - adafruit now have a breakout board for a super tiny MEMS microphone. Just like "classic" electret microphones, MEMS mics can detect sound and convert it to voltage, but they don"t need ...

Spin two DC motors, step one bi-polar or uni-polar stepper, or fire off two solenoids with 1.2A per channel (3A peak) using the TB6612. These are perhaps better known as "the drivers in our assembled Adafruit Motorshield or Mot...

So many accelerometers and so little time! Adafruit"ve expanded our accelerometer selection even more with this high-precision and inexpensive MMA8451 Triple-Axis Accelerometer w/ 14-bit ADC. You can detect motion, tilt and bas...

For microcontrollers without an analog-to-digital converter or when you want a higher-precision ADC, the ADS1115 provides 16-bit precision at 860 samples/second over I2C. The chip can be configured as 4 single-ended input channels, or two differentia...

Adafruit"ve now got a wider range version of favorite triple-axis accelerometer - it even has an on-board 3.3V regulator - making it a perfect choice for interfacing with a 5V microcontroller such as the Arduino. This breakout comes with 3 analog...

Adafruit updated their favorite triple-axis accelerometer to now have an on-board 3.3V regulator - making it a perfect choice for interfacing with a 5V microcontroller such as the Arduino. This breakout comes with 3 analog outputs for X, Y and Z axis...

Adafruit now have really lovely digital ADXL345 from Analog Devices, a triple-axis accelerometer with digital I2C and SPI interface breakout. Adafruit added an on-board 3.3V regulator and logic-level shifting circuitry, making it a perfect choice for...

Thermocouples are very sensitive, requiring a good amplifier with a cold-compensation reference. Adafruit have a couple digital thermocouple amplifiers in the shop already from Maxim. Now adafruit"re happy to introduce an excel...

EL tape is the big sister to EL wire - it has the same glow effect but with a flat, wide shape instead of a round shape. The glowing part of the tape is 1 cm wide (the plastic coating is about 1.5cm wide). The oth...

New, Adafruit updated this Pi plate so the buttons on on the right side, which makes it a little more mechanically stable.This pi plate is perfect for when you want to build a stand-alone project with its own user interface. The 4 directional buttons...

Our Adafruit Bluefruit LE (Bluetooth Smart, Bluetooth Low Energy, Bluetooth 4.0) nRF8001 Breakout allows you to establish an easy to use wireless link between your Arduino and any compatible iOS or Android (4.3+) device. It ...

Add an ear to your project with this well-designed electret microphone amplifier with AGC. This fully assembled and tested board comes with a 20-20KHz electret microphone soldered on. For the amplification, adafruit use the Maxim M...

FLORA is Adafruit"s fully-featured wearable electronics platform. It"s a round, sewable, Arduino-compatible microcontroller designed to empower amazing wearables projects.

Its a mini panel-mountable HDMI monitor with a built-in resistive touchscreen! So small and simple, you can use this display with any computer that has HDMI output, and the shape makes it easy to attach to a case or rail. This backpack fe...

Its a mini panel-mountable HDMI monitor with a built-in touchscreen! So small and simple, you can use this display with any computer that has HDMI output, and the shape makes it easy to attach to a case or rail. This backpack features the TFP401 for ...

This new Adafruit shield makes it easy to use a 16x2 Character LCD. Adafruit really like the Blue & White 16x2 LCDs we stock in the shop. Unfortunately, these LCDs do require quite a few digital pins, 6 to control the LC...

This I2C digital temperature sensor is one of the more accurate/precise adafruit"ve ever seen, with a typical accuracy of ±0.25°C over the sensor"s -40°C to +125°C range and precision of +0.0625&de...

Bring a little bit of Times Square into your home with this 16 x 32 RGB LED matrix panel. These panels are normally used to make video walls, here in New York we see them on the sides of busses and bus stops, to display anim...

These displays are small, only about 1" diameter, but very readable due to the high contrast of an OLED display. This display is made of 128x64 individual white OLED pixels, each one is turned on or off by the controller chip. Because the display...

These displays are small, only about 1.3" diagonal, but very readable due to the high contrast of an OLED display. This display is made of 128x64 individual white OLED pixels, each one is turned on or off by the controller chip. Because the displ...

These displays are small, only about 1" diagonal, but very readable due to the high contrast of an OLED display. This display is made of 128x32 individual white OLED pixels, each one is turned on or off by the controller chip. Because the display...

Make your own Arduino motor party with a motor shield and a fine assortment of motors! New! adafruit"ve upgraded the shield to our new version 2, with more powerful drivers, and uses fewer pins to boot! Included in this ...

This pressure sensor from Freescale is a great low-cost sensing solution for precision measurement of barometric pressure and altitude. The MPL3115A2 has a typical 1.5 Pascal resolution, which can resolve altitude at 0.3 met...

These displays were used in old Nokia 5110/3310 cell phones (before the smart-phone fad turned every cell phone into a TV). It"s a 84x48 pixel monochrome LCD display. These displays are small, only about 1.5" diagonal, but very readable and c...

Yes, this is an adorable small television! The visible display measures only 4.3" (11cm) diagonal, the TFT comes with a NTSC/PAL driver board, enclosure and stand. The display is very easy to use - simply connect 12VDC to the 2.1mm center-...

We love our black and white monochrome displays but we also like to dabble with some color now and then. Our new 0.96" color OLED displays are perfect when you need an ultra-small display with vivid, high-contrast 16-bit color. The visible portio...

Put a temperature meter anywhere with this very handy display. This panel meter displays the temperature of the attached waterproof 1% thermistor in °C. It does require a DC voltage to run, at 4.5-30VDC. It has reverse polarity protection in case...

Best-selling PiTFT just got a fancy upgrade, now we have a version with a capacitive touchscreen! That"s right, instead of a resistive touchscreen, which requires a fingernail or stylus, you can now use a fingerpad. The screen looks much nicer, w...

Is this not the cutest little display for the Raspberry Pi? It features a 2.8" display with 320x240 16-bit color pixels and a resistive touch overlay. The plate uses the high speed SPI interface on the Pi and can use the mini display as a console...

Is this not the cutest, little display for the Raspberry Pi? It features a 3.5" display with 480x320 16-bit color pixels and a resistive touch overlay just like our popular original, but this one is engineered specifically to w...

By popular demand! We now have the plates from the ARDX available separately. Acrylic plate is engraved and cut here at the Adafruit factory. There are mounting holes for your Arduino and a space that fits a half sized bread...

Adafruit added lots of basic but essential goodies. First up, there"s a big prototyping area, half of which is "breadboard" style and half of which is "perfboard" style so you can wire up DIP chips, sensors, and the like. Along th...

Have you gazed longingly at large TFT displays - you know what I"m talking about here, 4", 5" or 7" TFTs with up to 800x480 pixels. Then you look at your Arduino. You love your Arduino (you really do!) but there"s no...

Getting touchy performance with your screen"s touch screen? Resistive touch screens are incredibly popular as overlays to TFT and LCD displays. Only problem is they require a bunch of analog pins and you have to keep polling th...

Getting touchy performance with your screen"s touch screen? Resistive touch screens are incredibly popular as overlays to TFT and LCD displays. If you want to connect one to a computer you need something to handle the analog to...

This is a fancy upgrade to standard 16x2 LCDs, instead of just having blue and white, or red and black, this LCD has full color RGB characters on a dark/black background! That means you can change the character display colors to anything you want - r...

Your electronics can now see in dazzling color with this lovely color light sensor. Adafruit found the best color sensor on the market, the TCS34725, which has RGB and Clear light sensing elements. An IR blocking filter, integrated on-chip and locali...

This new Adafruit shield makes it easy to use a 16x2 Character LCD. We really like the RGB LCDs adafruit stock in the shop both the RGB negative and RGB positive. Unfortunately, these LCDs do require quite a few digital pins...

New, Adafruit updated this Pi plate so the buttons on on the right side, which makes it a little more mechanically stable. This pi plate is perfect for when you want to build a stand-alone project with its own user interface. The 4 directional b...

New, Adafruit updated this Pi plate so the buttons on on the right side, which makes it a little more mechanically stable This pi plate is perfect for when you want to build a stand-alone project with its own user interface. The 4 directional bu...

An assortment of the most common sensors used in electronics. 9 sensors and 3 additional components to interface with the "analog world". Adafruit have some tutorials here, to get you started.

The 1.3" SHARP Memory LCD display is a cross between an eInk (e-paper) display and an LCD. It has the ultra-low power usage of eInk and the fast-refresh rates of an LCD. This model has a matt silver background, an...

This switched JST connector is the best way to quickly prototype with LiPoly batteries. On Adafruit paired a genuine JST connector with a slide switch that can do up to 600mA. Both are soldered onto a breadboard-friendly breakout. There"s two gro...

It"s a mini HDMI decoder board! So small and simple, you can use this board as an all-in-one display driver for TTL displays, or perhaps decoding HDMI/DVI video for some other project. This breakout features the TFP401 for decoding video, ...

This 7.0" TFT screen has lots of pixels, 800x480 to be exact, an LED backlight and a resistive touchscreen overlay. Its great for when you need a lot of space for graphics or a user interface. These screens are commonly seen in cons...

This 5.0" TFT screen has lots of pixels, 800x480 to be exact, an LED backlight and a resistive touchscreen overlay. Its great for when you need a lot of space for graphics or a user interface. These screens are commonly seen in consumer el...

Thermocouples are very sensitive, requiring a good amplifier with a cold-compensation reference. The MAX31855K does everything for you, and can be easily interfaced with any microcontroller, even one without an analog input. This breakout board has t...

Thermocouples are very sensitive, requiring a good amplifier with a cold-compensation reference. So far Adafruit carried the MAX31855 which is an SPI interface thermocouple amplifier. The "855 is great but if you have a lot of thermocouples to me...

Because the Arduino (and Basic Stamp) are 5V devices, and most modern sensors, displays, flash cards and modes are 3.3V-only, many makers find that they need to perform level shifting/conversion to protect the 3.3V device from 5V.

This breakout board is the ultimate companion for the VLSI VS1053B DSP codec chip. The VS1053 can decode a wide variety of audio formats such as MP3, AAC, Ogg Vorbis, WMA, MIDI, FLAC, WAV (PCM and ADPCM). It can also be used to rec...

This is a pre-wired and waterproofed version of the DS18B20 sensor. Handy for when you need to measure something far away, or in wet conditions. While the sensor is good up to 125°C the cable is jacketed in PVC so we suggest keeping it under 100&...

These pretty strips of light are plastic diffused backlights, often seen in LCD displays. Normally they"re tucked behind the LCD and shine white light from below. Here, we"ve got the LEDs available individually a...

Yes, this is an adorable miniature television! The visible display measures only 1.5" diagonal, the TFT comes with a NTSC/PAL driver board. The display is very easy to use - simply connect 6-15VDC to the red and black wires, then connect a composite video source to the yellow and black wire. Voila, a television display! There"s a little button to adjust the LED backlight brightness (5 levels) - there is no other adjustment available but we found that the color and contrast look great right out of the box.

To demonstrate it, we took some photos with the display connected to a Raspberry Pi, but it will also work connected to any analog composite-video output such as a YBox or Propeller w/Video out. It will not work with a device that only outputs VGA, HDMI or any other digital video signal.

Please note, these miniature displays are very delicate and require care to avoid ripping the delicate flex connector. These are best used by electronics geeks who have experience and are comfortable working with delicate electronic components. WE CANNOT REPLACE DAMAGED DISPLAYS if you are not careful and rip the flex connector!