tft display vs led backlit quotation

IPS (In-Plane Switching) lcd is still a type of TFT LCD, IPS TFT is also called SFT LCD (supper fine tft ),different to regular tft in TN (Twisted Nematic) mode, theIPS LCD liquid crystal elements inside the tft lcd cell, they are arrayed in plane inside the lcd cell when power off, so the light can not transmit it via theIPS lcdwhen power off, When power on, the liquid crystal elements inside the IPS tft would switch in a small angle, then the light would go through the IPS lcd display, then the display on since light go through the IPS display, the switching angle is related to the input power, the switch angle is related to the input power value of IPS LCD, the more switch angle, the more light would transmit the IPS LCD, we call it negative display mode.

The regular tft lcd, it is a-si TN (Twisted Nematic) tft lcd, its liquid crystal elements are arrayed in vertical type, the light could transmit the regularTFT LCDwhen power off. When power on, the liquid crystal twist in some angle, then it block the light transmit the tft lcd, then make the display elements display on by this way, the liquid crystal twist angle is also related to the input power, the more twist angle, the more light would be blocked by the tft lcd, it is tft lcd working mode.

A TFT lcd display is vivid and colorful than a common monochrome lcd display. TFT refreshes more quickly response than a monochrome LCD display and shows motion more smoothly. TFT displays use more electricity in driving than monochrome LCD screens, so they not only cost more in the first place, but they are also more expensive to drive tft lcd screen.The two most common types of TFT LCDs are IPS and TN displays.

In market, LCD means passive matrix LCDs which increase TN (Twisted Nematic), STN (Super Twisted Nematic), or FSTN (Film Compensated STN) LCD Displays. It is a kind of earliest and lowest cost display technology.

LCD screens are still found in the market of low cost watches, calculators, clocks, utility meters etc. because of its advantages of low cost, fast response time (speed), wide temperature range,  low power consumption, sunlight readable with transflective or reflective polarizers etc.  Most of them are monochrome LCD display and belong to passive-matrix LCDs.

TFT LCDs have capacitors and transistors. These are the two elements that play a key part in ensuring that the TFT display monitor functions by using a very small amount of energy without running out of operation.

Normally, we say TFT LCD panels or TFT screens, we mean they are TN (Twisted Nematic) Type TFT displays or TN panels, or TN screen technology. TFT is active-matrix LCDs, it is a kind of LCD technologies.

TFT has wider viewing angles, better contrast ratio than TN displays. TFT display technologies have been widely used for computer monitors, laptops, medical monitors, industrial monitors, ATM, point of sales etc.

Actually, IPS technology is a kind of TFT display with thin film transistors for individual pixels. But IPS displays have superior high contrast, wide viewing angle, color reproduction, image quality etc. IPS screens have been found in high-end applications, like Apple iPhones, iPads, Samsung mobile phones, more expensive LCD monitors etc.

Both TFT LCD displays and IPS LCD displays are active matrix displays, neither of them can produce color, there is a layer of RGB (red, green, blue) color filter in each LCD pixels to make LCD showing colors. If you use a magnifier to see your monitor, you will see RGB color. With switch on/off and different level of brightness RGB, we can get many colors.

Neither of them can’t release color themselves, they have relied on extra light source in order to display. LED backlights are usually be together with them in the display modules as the light sources. Besides, both TFT screens and IPS screens are transmissive, it will need more power or more expensive than passive matrix LCD screens to be seen under sunlight.  IPS screens transmittance is lower than TFT screens, more power is needed for IPS LCD display.

The liquid crystal display (LCD) technology has been used in several electronic products over the years. There are more reasons for LCDs to be more endearing than CRTs.

A thin-film-transistor liquid-crystal display (TFT LCD) is a variant of a liquid-crystal display that uses thin-film-transistor technologyactive matrix LCD, in contrast to passive matrix LCDs or simple, direct-driven (i.e. with segments directly connected to electronics outside the LCD) LCDs with a few segments.

In February 1957, John Wallmark of RCA filed a patent for a thin film MOSFET. Paul K. Weimer, also of RCA implemented Wallmark"s ideas and developed the thin-film transistor (TFT) in 1962, a type of MOSFET distinct from the standard bulk MOSFET. It was made with thin films of cadmium selenide and cadmium sulfide. The idea of a TFT-based liquid-crystal display (LCD) was conceived by Bernard Lechner of RCA Laboratories in 1968. In 1971, Lechner, F. J. Marlowe, E. O. Nester and J. Tults demonstrated a 2-by-18 matrix display driven by a hybrid circuit using the dynamic scattering mode of LCDs.T. Peter Brody, J. A. Asars and G. D. Dixon at Westinghouse Research Laboratories developed a CdSe (cadmium selenide) TFT, which they used to demonstrate the first CdSe thin-film-transistor liquid-crystal display (TFT LCD).active-matrix liquid-crystal display (AM LCD) using CdSe TFTs in 1974, and then Brody coined the term "active matrix" in 1975.high-resolution and high-quality electronic visual display devices use TFT-based active matrix displays.

The liquid crystal displays used in calculators and other devices with similarly simple displays have direct-driven image elements, and therefore a voltage can be easily applied across just one segment of these types of displays without interfering with the other segments. This would be impractical for a large display, because it would have a large number of (color) picture elements (pixels), and thus it would require millions of connections, both top and bottom for each one of the three colors (red, green and blue) of every pixel. To avoid this issue, the pixels are addressed in rows and columns, reducing the connection count from millions down to thousands. The column and row wires attach to transistor switches, one for each pixel. The one-way current passing characteristic of the transistor prevents the charge that is being applied to each pixel from being drained between refreshes to a display"s image. Each pixel is a small capacitor with a layer of insulating liquid crystal sandwiched between transparent conductive ITO layers.

The circuit layout process of a TFT-LCD is very similar to that of semiconductor products. However, rather than fabricating the transistors from silicon, that is formed into a crystalline silicon wafer, they are made from a thin film of amorphous silicon that is deposited on a glass panel. The silicon layer for TFT-LCDs is typically deposited using the PECVD process.

Polycrystalline silicon is sometimes used in displays requiring higher TFT performance. Examples include small high-resolution displays such as those found in projectors or viewfinders. Amorphous silicon-based TFTs are by far the most common, due to their lower production cost, whereas polycrystalline silicon TFTs are more costly and much more difficult to produce.

The twisted nematic display is one of the oldest and frequently cheapest kind of LCD display technologies available. TN displays benefit from fast pixel response times and less smearing than other LCD display technology, but suffer from poor color reproduction and limited viewing angles, especially in the vertical direction. Colors will shift, potentially to the point of completely inverting, when viewed at an angle that is not perpendicular to the display. Modern, high end consumer products have developed methods to overcome the technology"s shortcomings, such as RTC (Response Time Compensation / Overdrive) technologies. Modern TN displays can look significantly better than older TN displays from decades earlier, but overall TN has inferior viewing angles and poor color in comparison to other technology.

Most TN panels can represent colors using only six bits per RGB channel, or 18 bit in total, and are unable to display the 16.7 million color shades (24-bit truecolor) that are available using 24-bit color. Instead, these panels display interpolated 24-bit color using a dithering method that combines adjacent pixels to simulate the desired shade. They can also use a form of temporal dithering called Frame Rate Control (FRC), which cycles between different shades with each new frame to simulate an intermediate shade. Such 18 bit panels with dithering are sometimes advertised as having "16.2 million colors". These color simulation methods are noticeable to many people and highly bothersome to some.gamut (often referred to as a percentage of the NTSC 1953 color gamut) are also due to backlighting technology. It is not uncommon for older displays to range from 10% to 26% of the NTSC color gamut, whereas other kind of displays, utilizing more complicated CCFL or LED phosphor formulations or RGB LED backlights, may extend past 100% of the NTSC color gamut, a difference quite perceivable by the human eye.

In 2004, Hydis Technologies Co., Ltd licensed its AFFS patent to Japan"s Hitachi Displays. Hitachi is using AFFS to manufacture high end panels in their product line. In 2006, Hydis also licensed its AFFS to Sanyo Epson Imaging Devices Corporation.

Less expensive PVA panels often use dithering and FRC, whereas super-PVA (S-PVA) panels all use at least 8 bits per color component and do not use color simulation methods.BRAVIA LCD TVs offer 10-bit and xvYCC color support, for example, the Bravia X4500 series. S-PVA also offers fast response times using modern RTC technologies.

When the field is on, the liquid crystal molecules start to tilt towards the center of the sub-pixels because of the electric field; as a result, a continuous pinwheel alignment (CPA) is formed; the azimuthal angle rotates 360 degrees continuously resulting in an excellent viewing angle. The ASV mode is also called CPA mode.

A technology developed by Samsung is Super PLS, which bears similarities to IPS panels, has wider viewing angles, better image quality, increased brightness, and lower production costs. PLS technology debuted in the PC display market with the release of the Samsung S27A850 and S24A850 monitors in September 2011.

TFT dual-transistor pixel or cell technology is a reflective-display technology for use in very-low-power-consumption applications such as electronic shelf labels (ESL), digital watches, or metering. DTP involves adding a secondary transistor gate in the single TFT cell to maintain the display of a pixel during a period of 1s without loss of image or without degrading the TFT transistors over time. By slowing the refresh rate of the standard frequency from 60 Hz to 1 Hz, DTP claims to increase the power efficiency by multiple orders of magnitude.

Due to the very high cost of building TFT factories, there are few major OEM panel vendors for large display panels. The glass panel suppliers are as follows:

External consumer display devices like a TFT LCD feature one or more analog VGA, DVI, HDMI, or DisplayPort interface, with many featuring a selection of these interfaces. Inside external display devices there is a controller board that will convert the video signal using color mapping and image scaling usually employing the discrete cosine transform (DCT) in order to convert any video source like CVBS, VGA, DVI, HDMI, etc. into digital RGB at the native resolution of the display panel. In a laptop the graphics chip will directly produce a signal suitable for connection to the built-in TFT display. A control mechanism for the backlight is usually included on the same controller board.

The low level interface of STN, DSTN, or TFT display panels use either single ended TTL 5 V signal for older displays or TTL 3.3 V for slightly newer displays that transmits the pixel clock, horizontal sync, vertical sync, digital red, digital green, digital blue in parallel. Some models (for example the AT070TN92) also feature input/display enable, horizontal scan direction and vertical scan direction signals.

New and large (>15") TFT displays often use LVDS signaling that transmits the same contents as the parallel interface (Hsync, Vsync, RGB) but will put control and RGB bits into a number of serial transmission lines synchronized to a clock whose rate is equal to the pixel rate. LVDS transmits seven bits per clock per data line, with six bits being data and one bit used to signal if the other six bits need to be inverted in order to maintain DC balance. Low-cost TFT displays often have three data lines and therefore only directly support 18 bits per pixel. Upscale displays have four or five data lines to support 24 bits per pixel (truecolor) or 30 bits per pixel respectively. Panel manufacturers are slowly replacing LVDS with Internal DisplayPort and Embedded DisplayPort, which allow sixfold reduction of the number of differential pairs.

Backlight intensity is usually controlled by varying a few volts DC, or generating a PWM signal, or adjusting a potentiometer or simply fixed. This in turn controls a high-voltage (1.3 kV) DC-AC inverter or a matrix of LEDs. The method to control the intensity of LED is to pulse them with PWM which can be source of harmonic flicker.

The bare display panel will only accept a digital video signal at the resolution determined by the panel pixel matrix designed at manufacture. Some screen panels will ignore the LSB bits of the color information to present a consistent interface (8 bit -> 6 bit/color x3).

With analogue signals like VGA, the display controller also needs to perform a high speed analog to digital conversion. With digital input signals like DVI or HDMI some simple reordering of the bits is needed before feeding it to the rescaler if the input resolution doesn"t match the display panel resolution.

Kawamoto, H. (2012). "The Inventors of TFT Active-Matrix LCD Receive the 2011 IEEE Nishizawa Medal". Journal of Display Technology. 8 (1): 3–4. Bibcode:2012JDisT...8....3K. doi:10.1109/JDT.2011.2177740. ISSN 1551-319X.

Brody, T. Peter; Asars, J. A.; Dixon, G. D. (November 1973). "A 6 × 6 inch 20 lines-per-inch liquid-crystal display panel". 20 (11): 995–1001. Bibcode:1973ITED...20..995B. doi:10.1109/T-ED.1973.17780. ISSN 0018-9383.

K. H. Lee; H. Y. Kim; K. H. Park; S. J. Jang; I. C. Park & J. Y. Lee (June 2006). "A Novel Outdoor Readability of Portable TFT-LCD with AFFS Technology". SID Symposium Digest of Technical Papers. AIP. 37 (1): 1079–82. doi:10.1889/1.2433159. S2CID 129569963.

Kim, Sae-Bom; Kim, Woong-Ki; Chounlamany, Vanseng; Seo, Jaehwan; Yoo, Jisu; Jo, Hun-Je; Jung, Jinho (15 August 2012). "Identification of multi-level toxicity of liquid crystal display wastewater toward Daphnia magna and Moina macrocopa". Journal of Hazardous Materials. Seoul, Korea; Laos, Lao. 227–228: 327–333. doi:10.1016/j.jhazmat.2012.05.059. PMID 22677053.

An LED-backlit LCD is a liquid-crystal display that uses LEDs for backlighting instead of traditional cold cathode fluorescent (CCFL) backlighting.TFT LCD (thin-film-transistor liquid-crystal display) technologies as CCFL-backlit LCDs, but offer a variety of advantages over them.

While not an LED display, a television using such a combination of an LED backlight with an LCD panel is advertised as an LED TV by some manufacturers and suppliers.

LED-backlit LCDs are not self-illuminating (unlike pure-LED systems). There are several methods of backlighting an LCD panel using LEDs, including the use of either white or RGB (Red, Green, and Blue) LED arrays behind the panel and edge-LED lighting (which uses white LEDs around the inside frame of the TV and a light-diffusion panel to spread the light evenly behind the LCD panel). Variations in LED backlighting offer different benefits. The first commercial full-array LED-backlit LCD TV was the Sony Qualia 005 (introduced in 2004), which used RGB LED arrays to produce a color gamut about twice that of a conventional CCFL LCD television. This was possible because red, green and blue LEDs have sharp spectral peaks which (combined with the LCD panel filters) result in significantly less bleed-through to adjacent color channels. Unwanted bleed-through channels do not "whiten" the desired color as much, resulting in a larger gamut. RGB LED technology continues to be used on Sony BRAVIA LCD models. LED backlighting using white LEDs produces a broader spectrum source feeding the individual LCD panel filters (similar to CCFL sources), resulting in a more limited display gamut than RGB LEDs at lower cost.

Using PWM (pulse-width modulation), a technology where the intensity of the LEDs are kept constant but the brightness adjustment is achieved by varying a time interval of flashing these constant light intensity light sources,

A first dynamic "local dimming" LED backlight was public demonstrated by BrightSide Technologies in 2003,Sony in September 2008 on the 40-inch (1,000 mm) BRAVIA KLV-40ZX1M (known as the ZX1 in Europe). Edge-LED lighting for LCDs allows thinner housing; the Sony BRAVIA KLV-40ZX1M is 1 cm thick, and others are also extremely thin.

LED-backlit LCDs have longer life and better energy efficiency than plasma and CCFL LCD TVs.mercury, an environmental pollutant, in their manufacture. However, other elements (such as gallium and arsenic) are used in the manufacture of the LED emitters; there is debate over whether they are a better long-term solution to the problem of screen disposal.

Because LEDs can be switched on and off more quickly than CCFLs and can offer a higher light output, it is theoretically possible to offer very high contrast ratios. They can produce deep blacks (LEDs off) and high brightness (LEDs on). However, measurements made from pure-black and pure-white outputs are complicated by edge-LED lighting not allowing these outputs to be reproduced simultaneously on screen.

Quantum dots are photoluminescent; they are useful in displays because they emit light in specific, narrow normal distributions of wavelengths. To generate white light best suited as an LCD backlight, parts of the light of a blue-emitting LED are transformed by quantum dots into small-bandwidth green and red light such that the combined white light allows a nearly ideal color gamut to be generated by the RGB color filters of the LCD panel. The quantum dors may be in a separate layer as a quantum dot enhacement film, or replace pigment-based green and red resists normally used in LCD color filters. In addition, efficiency is improved, as intermediate colors are no longer present and do not have to be filtered out by the color filters of the LCD screen. This can result in a display that more accurately renders colors in the visible spectrum. Companies developing quantum dot solutions for displays include Nanosys, 3M as a licensee of Nanosys, QD Vision of Lexington, Massachusetts, US and Avantama of Switzerland.Consumer Electronics Show 2015.quantum dot displays at CES 2017 and later formed the "QLED Alliance" with Hisense and TCL to market the technology.

Mini LED displays are LED-backlit LCDs with mini-LED–based backlighting supporting over a thousand full array local dimming (FALD) zones, providing deeper blacks and a higher contrast ratio.

LED backlights are often dimmed by applying pulse-width modulation to the supply current, switching the backlight off and on more quickly than the eye can perceive. If the dimming-pulse frequency is too low or the user is sensitive to flicker, this may cause discomfort and eyestrain similar to the flicker of CRT displays at lower refresh rates.

Competing display technologies for the best image performance; A.J.S.M. de Vaan; Journal of the society of information displays, Volume 15, Issue 9 September 2007 Pages 657–666; http://onlinelibrary.wiley.com/doi/10.1889/1.2785199/abstract?

Novitsky, Tom; Abbott, Bill (12 November 2007). "Driving LEDs versus CCFLs for LCD backlighting". EE Times. Archived from the original on 28 November 2010. Retrieved 21 November 2020.

LED TVs: 10 things you need to know; David Carnoy, David Katzmaier; CNET.com/news; 3 June 2010; https://www.cnet.com/news/led-tvs-10-things-you-need-to-know/

Chen, Haiwei; Zhu, Ruidong; Li, Ming-Chun; Lee, Seok-Lyul; Wu, Shin-Tson (24 January 2017). "Pixel-by-pixel local dimming for high-dynamic-range liquid crystal displays". Optics Express. 25 (3): 1973. doi:ISSN 1094-4087.

Controlling Power Consumption for Displays With Backlight Dimming; Claire Mantel et al; Journal of Display Technology; Volume: 9, Issue: 12, Dec. 2013; https://ieeexplore.ieee.org/document/6520956

Broadband reflective polarizers based on form birefringence for ultra-thin liquid crystal displays; S.U. Pan; L. Tan and H.S. Kwok; Vol. 25, No. 15; 24 July 2017; Optics Express 17499; https://www.osapublishing.org/oe/viewmedia.cfm?uri=oe-25-15-17499&seq=0

Get rich colors, detailed images, and bright graphics from an LCD with a TFT screen. Our standard Displaytech TFT screens start at 1” through 7” in diagonal size and have a variety of display resolutions to select from. Displaytech TFT displays meet the needs for products within industrial, medical, and consumer applications.

TFT displays are LCD modules with thin-film transistor technology. The TFT display technology offers full color RGB showcasing a range of colors and hues. These liquid crystal display panels are available with touchscreen capabilities, wide viewing angles, and bright luminance for high contrast.

Our TFT displays have LVDS, RGB, SPI, and MCU interfaces. All Displaytech TFT LCD modules include an LED backlight, FPC, driver ICs, and the LCD panel.

We offer resistive and capacitive touch screens for our 2.8” and larger TFT modules. Our TFT panels have a wide operating temperature range to suit a variety of environments. All Displaytech LCDs are RoHS compliant.

We also offer semi-customization to our standard TFT screens. This is a cost-optimized solution to make a standard product better suit your application’s needs compared to selecting a fully custom TFT LCD. Customizations can focus on cover glass, mounting / enclosures, and more - contact us to discuss your semi-custom TFT solution.

The Capacitive touch panel is activated with anything containing an inductive load such as a finger or stylus. It allows for multi-touch options. When using the capacitive touch screen, the display needs a separate controller to interface with the touch panel. The display for capacitive touch is brighter since the touch panel is transparent.

The Transmissive polarizer is best used for displays that run with the backlight on all the time. This polarizer provides the brightest backlight possible. If you have a need for a bright backlight with lower power drain, transmissive is a good choice for this TFT LCD display.

Focus LCDs can provide many accessories to go with your display. If you would like to source a connector, cable, test jig or other accessory preassembled to your LCD (or just included in the package), our team will make sure you get the items you need.Get in touch with a team member today to accessorize your display!

Focus Display Solutions (aka: Focus LCDs) offers the original purchaser who has purchased a product from the FocusLCDs.com a limited warranty that the product (including accessories in the product"s package) will be free from defects in material or workmanship.

EL backlight is obsolete technology, it is disappearing. CCFL backlight is disappearing, too. They are both being replaced by LED Backlight. I have never heard anyone ask for a quote about CCFL backlight. But every now and then, I can hear my customers ask about EL backlight, so let us dig in and find out “What is EL backlight?” and “Why EL backlight still has market demand?”

I think I have already given you the answer. We can see that among all the light sources of backlight, EL backlight is the thinnest one. I am sure that the trend of LED backlight is becoming super thin and lightweight. I have made the thinnest LED backlight for one of my clients. The light guide plate is as thin as 0.6 mm, but it is the best we can do. The total thickness of LED backlight is 0.9 mm. You may not know that it caused lots of trouble for us. 0.6 mm is too thin to install SMD LED into PCB in the traditional way. The minimum thickness of PCB to install SMD is 1.0 mm, so we have to make a dedicated FPC for it.

Even if you still think it is not bright enough, we can double the SMD LEDs or even triple the SMD LEDs by increasing the thickness of light guide plate from 3.0 mm to 6.0 mm and 9.0 mm.

Then the brightness will be double or triple. Please see the picture above. I admit that is insane. It is too expensive. Usually, edge LED backlight with two edges that are installed with SMD LEDs is more than enough in the brightness.

Generally, the pitch between two SMD LEDs is 20.0 mm. But we can make it 10.0 mm, even 5.0 mm, so we can make the numbers of SMD LEDs double or fourfold.

This is crazy. It will be incredibly expensive. We have never made the pitch 5.0 mm bottom LED backlight for any of my customers before. I just want to tell you it is possible that we can increase the brightness of LED backlight.

◆ Color. EL backlight usually only has one color which is white. And LED backlight is much better in color saturation and color variousness. Seethe advantages of LED backlight.

Actually, we print all the colors we want on the diffusion film and use white light as light source. See the picture above, we print purple, yellow, red, orange, pink on the diffusion film and use the black lightproof paper to cover the part we don’t want to emit light. Finally, we use an electronic controller to control the display, which we need to input the control program in the control IC.

Theoretically, the using time of LED backlight is 100,000 hours and the using time of EL backlight is 10,000 hours. But practically, the using time of LED backlight is 20,000~30,000 hours and the using time of EL backlight is 2000~3000 hours. The practically using time is determined by so many factors and there is a huge difference in each individual.

3 LED lamps and 1 electronic resistor are serially connected as one group. The driving voltage is 12V. I am not here to talk aboutthe benefit of LED Serial and Parallel Hybrid Connection.

We have over two dozen TFT LCD display modules to choose from. All of them are full-color graphic displays. Unlike standard monochrome character displays, you can create complex images for imaginative user experiences. Thin and light, these are ideal for handheld devices, communications equipment, information displays, and test and measurement equipment.

Listed by the diagonal size of the active area (the usable area for lit pixels), our TFT display sizes range from 1.3 inches to 10.1 inches. Choose from six different interfaces, many of our TFT modules have more than one interface available. Arduino users should select modules with SPI for fast and easy communications to add color graphics to their projects.

Contrast ratio is the difference between a pixel that is lit or dark. Standard STN LCD displays typically have a 10:1 contrast ratio while TFT displays are 300:1 and up, so details stand out and text looks extra sharp. For standard STN displays, you must choose a display limited to a specific viewing angle (12, 3, 6 or 9 o"clock) while TFTs can have a viewing cone greater than 160 degrees.

To speed up your design time, we sell carrier boards and demonstration kits for selected modules. For outdoor use, be sure to look at our sunlight readable displays.

If you’re designing a display application or deciding what type of TV to get, you’ll probably have to choose between an OLED or LCD as your display type.

Not sure which one will be best for you? Don’t worry! We’re here to help you figure out the right display for your project or application. In this post we’ll break down the pros and cons of these display types so you can decide which one is right for you.

LCDs utilize liquid crystals that produce an image when light is passed through the display. OLED displays generate images by applying electricity to organic materials inside the display.OLED and LCD Main Difference:

These different technological approaches to display technology have big impact in some features including contrast, brightness, viewing angles, lifespan, black levels, image burn-in, and price.

Everything from the environment your display will be used in, your budget, to the lighting conditions and the required durability will play a part in this decision.

Contrast refers to the difference between the lightest and darkest parts of an image. High contrast will produce sharper images and more easily readable text. It’s a crucial quality for high fidelity graphics and images or to make sure that a message on a display is very visible.

graphics and images visible. This is the reason you’re still able to see light coming through on images that are meant to be dark on an LCD monitor, display, or television.

OLEDs by comparison, deliver a drastically higher contrast by dynamically managing their individual pixels. When an image on an OLED display uses the color black, the pixel shuts off completely and renders a much higher contrast than that of LCDs.OLED vs LCD - Who is better at contrast?

Having a high brightness level is important if your display is going to be used in direct sunlight or somewhere with high ambient brightness. The display"s brightness level isn"t as important if it’s going to be used indoors or in a low light setting.OLED vs LCD - Who is better at Brightness?

This means the display is much thinner than LCD displays and their pixels are much closer to the surface of the display, giving them an inherently wider viewing angle.

LCDs with IPS are significantly brighter than standard LCDs and offer viewing angles that are on-par with OLEDs.OLED vs LCD - Who is better at Viewing Angles?

LCDs have been on the market much longer than OLEDs, so there is more data to support their longevity. On average LCDs have proven to perform for around 60,000 hours (2,500) days of operation.

With most LCDs you can expect about 7 years of consistent performance. Some dimming of the backlight has been observed but it is not significant to the quality of the display.

OLEDs are a newer technology in the display market, which makes them harder to fully review. Not only does OLED technology continue to improve at a rapid pace, but there also hasn’t been enough time to thoroughly observe their performance.

You must also consider OLED’s vulnerability to image burn-in. The organic material in these displays can leave a permanent afterimage on the display if a static image is displayed for too long.

So depending on how your OLED is used, this can greatly affect its lifespan. An OLED being used to show static images for long periods of time will not have the same longevity as one displaying dynamic, constantly moving images.OLED vs LCD - Which one last longer?

There is not yet a clear winner when it comes to lifespans between LCD and OLED displays. Each have their advantages depending on their use-cases. It’s a tie!

For a display application requiring the best colors, contrast, and viewing angles – especially for small and lightweight wearable devices – we would suggest an OLED display.

If you’re a gamer then look out for Variable Refresh Rate (VRR) technologies which will significantly improve fluidity in gaming and avoid stuttering, tearing or lag associated with older Vsync technologies. At the moment your choice depends on your graphics card vendor, either AMD FreeSync or NVIDIA G-sync.

PLS (Plane to Line Switching)= S-PLS, a Samsung technology exclusive to them and very similar to LG.Display’s IPS in performance and can therefore be called an “IPS-type” technology

AHVA (Advanced Hyper-Viewing Angle) = developed by AU Optronics as another alternative to LG.Display’s IPS, very similar again and so can be called “IPS-type”

Dynamic contrast ratios – perhaps the most overly exaggerated specs in the modern market. You will see figures in the millions now, but these are largely meaningless. Dynamic contrast ratios involves controlling the backlight of the screen automatically, depending on the content shown on the screen. In bright images, the backlight is increased, and in darker images, it is decreased. There is no real need to have a DCR of over 10,000:1 as you just wouldn’t notice the difference in practice. The figures being quoted now are based on measurements of monitor states which would just never occur in real use. In fact modern DCR’s of LED backlit screens assume the “black” state is in fact when the backlighting is turned off, in which case DCR would effectively be tending towards infinity:1. Just ignore DCR figures are they are not a reliable spec. In practice you would never achieve the numbers quoted. Far more important really is how effective the mechanism is and whether it is smooth and at what speed changes are made. Also keep in mind many people don’t even like the technology at all!

Colour gamut – don’t assume that a higher colour gamut is better! The gamut represents the colour space that the backlighting unit of the monitor allows the screen to display. You need to understand that most normal content is based on a certain colour space (sRGB) and that there can be issues if you view this using a wide gamut screen. See here for more information.

Backlighting – LED backlighting is becoming increasingly common in modern screens with manufacturers making a lot of claims which aren’t necessarily true. You need to understand what different backlighting will actually offer you. In reality, LED backlighting in mainstream screens is based on White-LED (W-LED) backlight units and only really offers benefits in terms of power consumption, screen thickness, and in environmental considerations. See this article for more information.

A. Generally nowadays with all the ultra-low response time models available, ghosting caused by slow pixel response times is just not an issue for the majority of users. Performance has improved significantly over the years and blurring and ghosting has been largely eliminated on the faster displays. The use of RTC technologies (overdrive) significantly helps improve response times and speed up pixel transitions. This is particularly important on IPS/VA type displays which can be very slow where RTC is not used. Look out for response time specs quoted with a “G2G” (grey to grey) response time as that should indicate the use of overdrive technologies.

Nowadays screens supporting high refresh rates (120Hz+) input frequencies are becoming more and come common, and these can help reduce motion blur and ghosting and improve gaming performance considerably. They are also able to support higher frame rates than traditional 60Hz displays and some are also capable of supporting 3D stereoscopic content through active shutter glasses. Do be careful of assuming that a screen advertised as supporting 3D is in fact able to support 120Hz though, as some 3D models do not support this and instead use passive methods to produce the 3D effect (see here for more info on 3D technologies). Refresh rate of the panel does have a direct impact on motion clarity and for optimal gaming performance you will want to consider those high refresh rate displays above 60Hz.

Ghosting and motion blur perception may also depend on how susceptible you are as a user, as one person may see no ghosting, another may see lots on the same panel. The best bet is to try and see a TFT in action in a shop and see for yourself, if that’s not possible you will have to settle for the opinions of other users and take the plunge! Also be careful to get an idea of real life performance in practice, and don’t just rely on quoted specs. While they are often a good rough guide to the gaming performance, they are not always reliable.

One area which cannot be eliminated fully through response time improvements is perceived motion blur. This is related to how the human eye tracks movement on hold-type displays like LCD’s. In recent years several methods have been used to help provide improved motion blur for users. Models featuring LightBoost backlights for 3D gaming were found to be “hackable” to bring about motion blur benefits through the use of their strobed backlight system. Other displays have now introduced native strobed backlights to offer similar benefits. Look out for models with Motion Blur Reduction backlights like the BenQ XL2420Z / XL2720Z (Blur Reduction mode), Eizo Foris FG2421 (Turbo 240) and Asus ROG Swift PG278Q (ULMB) for instance. ULMB as a feature is common on NVIDIA G-sync enabled displays where high refresh rate is used.

A. As a rule of thumb, it would normally be best to use the digital video connection end to end to connect your device to your monitor. For a PC, this would commonly be DisplayPort, HDMI or DVI which offer a pure digital end to end connection between the graphics card and the monitor. DisplayPort is needed to run the high resolution/high refresh rate panels so you will need to ensure your graphics card has a DP output. Some screens or cards use Mini DP instead of the full size version, but that is simply a different size connection and can be easily inter-changed with “normal” DisplayPort. Cables which are DP at one end, and Mini DP at the other are common and simple to use.

HDMI and DisplayPort are also common digital connections now being offer, but unlike DVI are also capable of carrying audio as well as video. The picture quality should not be any different between DVI, HDMI and DisplayPort in theory as long as no additional video “enhancements” are applied when using one over the other. Bandwidth requirements will vary so this might influence which type you need to use depending on the screen resolution and refresh rate.

Converting between DVI and HDMI is easy and cables are readily available to offer that if needed (keeping in mind you will lose the sound transmission when it reaches the DVI). Converting between DVI/HDMI and DisplayPort is far more tricky and not simple to achieve. It is very hit and miss and working active adapters are expensive. We would advise avoiding the attempt to convert DP to HDMI/DVI if you can.

A. There is a lot of talk about colour depth on TFT screens, now more than ever with the emergence of 6-bit IPS and VA panels. At one time TN Film was the main 6-bit technology but today that is no longer the case. It’s important to put this into perspective though, and not jump on the bandwagon of 8-bit being much, much better than 6-bit. Or even 10-bit being much better than 8-bit.

An 8-bit display would offer a colour palette of 16.7 million colours. They offer a ‘true’ colour palette, and are generally the choice of manufacturers for colour critical displays over 6-bit panels. On the other hand modern 6-bit screens use a range of Frame Rate Control (FRC) technologies to extend the colour palette from 262,144 colours to around 16.7m. In fact on many modern panels these FRC are very good and in practice you’d be hard pressed to spot any real difference between a 6-bit + FRC display and a true 8-bit display. Colour range is good, screens show no obvious gradation of colours, and they show no FRC artefacts or glitches in normal everyday use. Most average users would never notice the difference and so it is more important to think about the panel technology and your individual uses than get bogged down worrying about 6-bit vs. 8-bit arguments.

Manufacturers use 6-bit panels (+FRC) to help keep costs lower. As a result, a modern range of IPS and VA panels is also now produced which use 6-bit colour depth (+FRC) instead of true 8-bit colour depths. At the other end of the scale there are also some panels which can offer support of 10-bit colour depth. Again these come in two flavours, being either a true 10-bit panel (quite rare and expensive) offering 1.07 billion colours or an 8-bit panel with an additional FRC stage added (1.07 billion colours produced through FRC). The 8-bit +FRC panels are of course more common and will often be used to offer “10-bit” support in desktop displays. With 10-bit colour though there is also an additional consideration which is whether you would ever even be able to use this in your work. You can also only make use of this 10-bit support if you have a full end-to-end 10-bit workflow, including a supporting software, graphics card and operating system which is still very rare and expensive for most users. So for many people the use of a 10-bit capable panel is rather meaningless.

The colour space / gamut capability of a monitor is not determined by the panel technology, but rather by the backlight technology being used. Traditional screens used standard CCFL backlighting which (for simplicity of comparison here) offered a colour space covering the sRGB space almost exactly, which equates to about 72% of the now popular NTSC reference space. With backlighting technology changes and improvements, some screens then started to use WCG-CCFL (Wide Colour Gamut CCFL) backlighting which can offer an extended gamut covering commonly 92% – 102% of the NTSC reference space. Other backlighting technologies like W-LED (White LED) are also becoming very common, and at the moment cover the sRGB space (~68 – 72% NTSC). Some other LED backlights using RGB LED can cover >100% of the NTSC space as well but are prohibitively expensive and rarely used.

While a larger colour space might sound like a good idea, it’s not always for everyone. You need to keep in mind what content you will be viewing on the screen, and what colour space that content is based on. Since sRGB is very common and the standard for many things like Windows and the internet, viewing sRGB content on an extended gamut screen can cause oversaturation of colours and an unrealistic ‘stretching’ of the colours. Reds and greens in particular can appear quite ‘neon’ and some users do not like this. The smaller colour space of the content is, as a very crude description, ‘stretched’ over the larger colour space of the monitor. On the other hand, some applications are colour space aware (e.g. Adobe Photoshop) and so if you are working with extended gamut content, you will prefer an extended gamut screen. I’d certainly recommend reading more into this as it is only a brief summary here. Where a screen has an extended gamut, they sometimes provide an sRGB emulation mode which work to varying degrees. Handy if you might need to use it, but make sure the screen offers a decent performance when in this mode and that it works. At the end of the day, the choice of monitor might very well depend on the colour space you want to work with. For most average users a standard CCFL or W-LED backlit display with a standard sRGB gamut would probably be preferred.

A. The simplest and cheapest way to clean a TFT screen is with a slightly damp cloth; wipe off the left behind water with a towel or similar then smooth/dry completely with a yellow polishing cloth. Be careful not to use products such as toilet paper and kitchen roll as they contain lint and can leave scratches on your beloved screen! Cleaning solution from opticians and lint free clothes for lens cleaning are also very good.

A. Unfortunately dead pixels can be an issue on TFT screens as they are often developed during the manufacturing stage. For retail costs to be kept low the companies cannot afford to make all screens defect-free and check for dead pixels all the time. Pixels can be described in the following ways:

If you want to ensure that you receive a pixel perfect screen (and who wouldn’t at the kind of prices you are paying for the TFT!?!) then you can often pay for pixel checks from some online retailers. Beware though! Never buy a TFT from retailers who offer the pixel check without having the check done as you can be sure the screens they find to be non-perfect will be winging their way to the customers who don’t have the check! The only other option to ensure you get a pixel perfect screen is to check out the panel in a shop in person, then you can see for yourself…..

If you find you have a dead pixel there is not a lot you can do unfortunately. If you have a certain number of dead pixels (usually at least 3 or a certain number centrally on the panel) then the manufacturer will replace the TFT for you, but the number of dead pixels needed before this happens varies between each manufacturer, so check with them before you order if you’re concerned.

If you still have a dead pixel problem, can’t bring it back to life and can’t RMA it under warranty then you can sometimes return it to the stockist if you purchased it online. If you bought online you can take advantage of the “Distance Selling Act” which entitles you to return any item within 7 days as you were not present at the time of purchase. If you are not happy with your TFT you can return it at your cost of postage and often claim a refund or exchange. However, be aware that a lot of places will try and charge you restocking fees and they will almost certainly specify the goods must be packaged and in the same condition as when you received it, so be careful to package it back up nicely. Legally, if the stocker accepts the TFT back as a return governed by the Distance Selling Act, then they are NOT allowed to charge you a restocking fee as covered in the Government Regulations. This selling act is not widely advertised by retailers, but does exist if you really need to use it. You should only have to pay for postage to send it back to them.