adafruit tft lcd display model 1480 factory

The 2.2" display has 320x240 color pixels. Unlike the low cost "Nokia 6110" and similar LCD displays, which are CSTN type and thus have poor color and slow refresh, this display is a true TFT! The TFT driver (ILI9340 or compatible) can display full 18-bit color (262,144 shades!). And the LCD will always come with the same driver chip so there"s no worries that your code will not work from one to the other.

The Adafruit TFT FeatherWing has a touch screen display on the front and a socket for any Feather on the back, including the Particle Argon, Boron, and Xenon. You can find technical information at Adafruit.

To download. click the DOWNLOADS button in the top right corner, rename the uncompressed folder Adafruit_ILI9341. Check that the Adafruit_ILI9341 folder contains Adafruit_ILI9341.cpp and Adafruit_ILI9341.

Place the Adafruit_ILI9341 library folder your arduinosketchfolder/libraries/ folder. You may need to create the libraries subfolder if its your first library. Restart the IDE

With four bright white LED backlight and 240 x 320 pixels with individual RGB pixel control, this colour 2.8in. TFT display features a resistive touchscreen for fingertip detection across the entire screen surface. The workload is lifted from the microcontroller by a built-in controller equipped with RAM buffering, and the display board has two modes: 8-bit and SPI.

To download. click the DOWNLOADS button in the top right corner, rename the uncompressed folder Adafruit_ILI9341. Check that the Adafruit_ILI9341 folder contains Adafruit_ILI9341.cpp and Adafruit_ILI9341.

Place the Adafruit_ILI9341 library folder your arduinosketchfolder/libraries/ folder. You may need to create the libraries subfolder if its your first library. Restart the IDE

2.8" TFT LCD touch screen graphic display with 320 x 240 px resolution and 18-bit colour depth. It works with both 3.3 V and 5 V. Additionally, there is a micro SD memory card reader on the board.

The screen is based on the ILI934 controller and has a built-in RAM memory, so the microcontroller is not burdened with display control. The device can communicate in two modes: 8-bit mode and via SPI bus. For 8-bit mode, eight digital data lines and four control lines must be connected. SPI requires only five transmission lines, but is slower than 8-bit communication. In addition, four additional pins are required to operate the touch screen.

The leads areholes for the includedgoldpin connector- 2.54 mm raster (for self-soldering). They allow for connection of the display through wires or plugged into the contact plate.

We use our internationally recognized delivery partners UPS/DHL. Collection of ET10103581 can also be arranged for the customer by international shipments through contacting our customer support team. Additionally, you can also search "Adafruit Industries LLC" products on our website by using Enrgtech"s Unique Manufacturing Part Number ET10103581.

This awesome little display breakout is a great way to add a small, colorful and bright display to any project. Since the display uses 4-wire SPI to communicate and has its own pixel-addressable frame buffer, it can be used with every kind of microcontroller. Even a very small one with low memory and few pins available!

This 2.2″ display has 320×240 color pixels and is a true TFT display. The TFT driver (ILI9340 or compatible) can display full 18-bit color (262,144 shades). The breakout has the TFT display soldered on (it uses a delicate flex-circuit connector) as well as a ultra-low-dropout 3.3V regulator and a 3/5V level shifter so you can use it with 3.3V or 5V power and logic. Adafruit also had a little extra space on the back so there is a microSD card holder for easily loading full-color bitmaps from a FAT16/FAT32 formatted microSD card.

The Adafruit 2.2″ TFT LCD with MicroSD Card also features an EYESPI connector for a simpler connection to the LCD. EYESPI is a single 18-pin FPC used as a quick way to connect displays.