spi tft lcd display st7735 128x128 price

ER-TFTM1.44-2 is 128x128 pixel 1.44 inch color tft lcd display panel with ST7735S controller and breakout board,superior display quality,wide viewing angle,super and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO,ARM and Raspberry PI.It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.It"s 4-wire serial spi interface with pin header connection.It"s easily controlled by MCU such as 8051,PIC,AVR,ARDUINO,ARM and Raspberry Pi.It can be used in any embedded systems,industrial device,security,medical and hand-held device.

This lovely little display breakout is the best way to add a small, colorful and bright display on to your project. Since the display size is 1.44-inch and since TFT display has its own pixel-addressable frame buffer, it can be used with every kind of microcontroller. Even a very small one with low memory and few pins available!

In the above example, Node32-Lite and this 1.44-inch LCD.  Please refer to the tutorial here: ST7735S interfacing with ESP32 to make the connections, Arduino library installation, and modification needed for it to works on this LCD.

This lovely little display breakout is the best way to add a small, colorful and bright display on to your project. Since the display size is 1.44-inch and since TFT display has its own pixel-addressable frame buffer, it can be used with every kind of microcontroller. Even a very small one with low memory and few pins available!

In the below example, Node32-Lite and this 1.44-inch LCD. Please refer to the tutorial here: ST7735S interfacing with ESP32 to make the connections, Arduino library installation, and modification needed for it to works on this LCD.

Add some dazzle to your project with this 1.45" diagonal graphic TFT display module. This small display packs 128x128 full-color pixels into one square inch of active display area. It is a great choice when you need color and sharp detail while using minimal front panel space. At less than 5 grams, the display adds very little weight to handheld devices.

Thanks to the integrated Sitronix ST7735S or compatible controller, a single 3.3v source powers everything. The SPI host interface allows full read and write control of the display while using only 10 pins. The single bright white LED backlight has anode (A,+) and cathode (K, -) pins brought out on the Flexible Printed Circuit (FPC) tail. To connect, all you need is a standard 10-conductor, 0.5 mm ZIF socket such as Omron Electronics

While the SPI interface requires only a few lines to control this TFT LCD module, it is still possible to transfer data at a rate that supports 20 FPS (Frames Per Second) screen updates -- fast enough to play a full-motion video as shown in our videos.

To get started, download the datasheet and SPI sample code. And of course Crystalfontz is always here to help you when you integrate this display into your application.

Docked a star because mine was extremely delicate. The white bezel/holder if touched with the slightest of force, separates the screen layers. If turned upside down the entire thing can fall apart requiring reassembly of the screen. Very tedious to reassembly it cleanly without dust. I think the issue is that the double sided adhesive used is of subpar quality and is not very sticky. A very slight pressure on the white holder edges can remedy the issue, though be very careful not to press on the display itself or you might damage the screen.If you"re having trouble getting this display to work, here are the useful details. If you"re running it off an Arduino UNO or equivalent 3.3v or 5v microcontroller use the Adafruit ST7735 and ST7789 Library. I would not use the TFT_ILI9163C library, as when I tried it, it caused the screen to have corrupt 2-5 pixel band on one edge of the screen. Even though many places online will tell you to use that library, which is odd since this is a ST7735 screen and not a ILI9163C screen. Wiring is easy for an UNO, LED->3.3v, SCK->13, SDA->11, AO->8, Reset->Reset, CS->10, Ground->GND, VCC->3.3v. There is a voltage regulator on the back of the screen for the use of 5v power which is accompanied by a jumper pad. You can close the jumper pad to bypass the voltage regulator with a tiny blob of solder if you only have 3.3v microcontrollers. However if you supply 5v for VCC with the jumper closed you"ll probably destroy it. Since this is actually a 3.3 volt screen, it will not work without resistors on a 5v device like an UNO. If you use a 3.3 volt microcontroller you don"t need the resistors. If you"re using a 5v microcontroller then four 560 Ohm, 680 Ohm or 1k Ohm resistors are needed for the data lines SCK, SDA, AO, and CS, to pull the voltage down from the Arduino pins. I used four 680 Ohm resistors. The reset line must be connected to the reset pin on an Arduino, not pin 9. If you try to use pin 9 on the UNO you will cause the screen contrast to overwhelm the display causing weird ghosting. This is because the Arduino is 5v not 3.3v The reset pin can be used on pin 9 if another resistor is supplied, however I don"t see the point in adding another resistor when you can just use the reset pin. You can leave the resistors off if you use a multi channel 3v to 5v bidirectional level shifter or say a TXS0108E chip.Also if you"re using the Adafruit ST7735 and ST7789 library, you"ll want to use the initR function with INITR_144GREENTAB as the argument. That"s because the ST77XX chip that"s used on this board is a Sitronix ST7735R. Which is what the line tft.initR(INITR_144GREENTAB); tells the library to setup for.All in all, this is a fine display granted you get a working one. It"s able to draw very fast compared to larger screens with the same family of chip, probably because it"s only 128x128 pixels.

This 1.44 inch SPI TFT Color Screen LCD Display has 128 x 128 resolution and 262 colours. This Color Screen LCD Display uses SPI interface to communicate with the controller such as Arduino, it is the best upgrading of the Nokia5110.Unlike the low cost NOKIA6110 and similar LCD displays, which are CSTN type and thus have poor colour and slow refresh, this display is a true TFT! The TFT driver (ST7735R) can display a full 16-bit colour using our library code.

The breakout has the TFT display soldered on (it uses a delicate flex-circuit connector) as well as an ultra-low-dropout 3.3V regulator and a 3/5V level shifter so you can use it with 3.3V or 5V power and logic. We also had a little space so we placed a microSD card holder so you can easily load full colour bitmaps from a FAT16/FAT32 formatted microSD card.