ili9341 tft lcd 1.8 quotation

Spice up your Arduino project with a beautiful small display shield . This TFT display is small (1.8" diagonal) bright (4pcs white-LED chips) and colorful (18-bit 262,000 different shades)! 128x160 pixels with individual pixel control.

ER-TFTM018-2 is 128x160 dots 1.8" color tft lcd display with ILI9163 controller and breakoutboard,optional power supply for 3.3V or 5V and optional 4-wire resistive touch panel,superior display quality,super wide viewing angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO,ARM and Raspberry PI.It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!".Here is the link for1.8"TFT LCD Shield with Libraries, EXxamples.Schematic Diagram for Arduino Due,Mega 2560 and Uno. For 8051 microcontroller user,we prepared the detailed tutorial such as interfacing, demo code andDevelopment Kitat the bottom of this page.

Those results indicate there is no communication happening with the display chip for some reason. Since the TFT_eSPI library is not used for the test this indicates that the library will not be able to talk to the chip either.

This might not work but try it: The displays are fitted with a regulator (U1 on PCB) which is designed to accept 5V input and output 3.3V to the display. These are normally "Low Drop Out" (LDO) which means that if you connect 3.3V to them they still output about 3.0V and this is sufficient for the display chip. Your board may be fitted with a regulator that has a higher voltage loss, so it is worth trying to power the display from 5V connected to the VCC pin. The other option is to bypass the regulator U1 by soldering a link (or adding a big blob of solder) to short across J1 pads. This then links VCC direct to the TFT chip and thus VCC must only be 3.3V (5V with that link will damage the chip).

//#define ILI9488_DRIVER // WARNING: Do not connect ILI9488 display SDO to MISO if other devices share the SPI bus (TFT SDO does NOT tristate when CS is high)

Suitable 45-way, 0.5mm pitch, 0.3mm thickness (with stiffener) FFC/FPC connectors for use with these Displaytech TFT LCD display modules are: ; 738-8950 738-8950 , ; 772-7027 772-7027 or ; 772-6756 772-6756. Displaytech TFT LCD Display Modules. Displaytech"s TFT LCD display modules are designed to combine performance with value. These reliable TFT LCD modules are suitable for a wide variety of industrial, medical and consumer applications. The driver ICs are mounted directly on to the glass and are as follows: 1.8" TFT (128x160) - driver IC ILI9163C 2.2", 2.4" and 2.8" TFT (240x320) - driver IC ILI9341 3.5" TFT (320x240) - driver IC NT39016D 4.3" TFT (480x272) - driver IC HX8257-A The DT024DTFT 2.4" module ( ; 135-9775 135-9775 ) has an IPS display offering improved colour accuracy, a wider viewing angle, and high refresh rate. Transmissive TFT LCD display modules LED backlight DC voltage input Connection to drive the display module is via FPC (Flexible Printed Circuit) Operating temperature range: -20 to +70°C Viewing direction: 6 o ‘clock (DT035TFT and DT035TFT-TS are: 12 o ‘clock) Touch screen versions come fitted with a 4 wire resistive touch screen

Please see the DT028CTFT for reference designs. The schematics between the B and the C are the same with the exception that the B does not have the IPS interface.