bad tv lcd panel symptoms for sale

If your LCD television has ghosting, double images, dark on one side with slow refresh rates and symptoms similar to those shown in the pictures above there is a good chance we can fix it. You may find many Google sites and YouTube videos that show you how to "fix" this problem by applying pressure to the COF ribbons at the top of the LCD panel. That may work for a short time (or you may destroy the panel by trying to do it!) but in almost every case it will fail again in a month or two. It is sad that those posters never report back that the problem returned in such a short time. Tv Tech Electronics is part of a nationwide network of top technicians and through the combined efforts of that network we have developed a permanent repair for this problem. We have not had a single case where we performed this repair and the set came back again with the same problem. Sets smaller than 40 inches may not be repairable for this problem, but the larger sets often are. No other shop in the Kansas City area can repair this problem without replacing the panel at a cost that makes the repair uneconomical, give us a call at 816-756-0668 if your television displays this symptom.

If your TV isn’t working properly, there are still a few things to consider before you give up on it. Generally, you’ll have a few warning signs that things are not exactly right.

Of course, sometimes, the TV is beyond repair and you should replace it instead. If the screen is broken or the TV doesn’t turn on no matter what you do (or if the sound stopped working completely), it’s time to check out a new set.

The difference is that stuck pixels usually happen because of a problem with a transistor; they often have different colours and are usually just simply out of place. If it is a dead pixel, then the TV should be sent for repairs, as, unfortunately, the issue is a difficult one to fix.

If the colours on your screen appear distorted, then your TV might be malfunctioning. Traditionally, this issue tends to occur gradually, meaning that you might not notice any difference at first. This is due to the common factor that one colour tends to weaken at a time; therefore, no obvious changes happen overnight.

If your screen starts to display bars and lines, this tends to indicate that there is an issue with a connector. This can occur when something magnetic has been placed near the TV and, in turn could mess with the picture quite considerably, even potentially de-magnetising the screen.

The issue can be due to cables that have become loose inside the screen as well, which is an easy fix, although it may require a professional because the TV may have to be opened.

You may be able to do something about this by adjusting the levels of brightness and contrast on your TV and playing different types of content to see if the problem goes away. You can also enable your TV’s Pixel Shift feature; when this feature is turned on, images on the screen move a bit to vary the pixels used. Pixel Shift is often included in modern sets and might clean out the phantom image.

This issue could occur if the signal received is a digitised standard (480p), as there’s a discrepancy between the resolution and the display. It’s also worth noting that the digital signal your TV receives can be affected by weather conditions as well, so the image can appear fuzzy and glitchy.

However, the good news is that, when this happens to modern televisions, there is a high chance of it being fixed, so you can still enjoy your TV for a long time.

If the TV is on but the picture is faded on some areas of the screen, it’ll be difficult for you to actually enjoy the content. You may try to ignore the stain-like mark but there is no denying that this will impact your experience. Faded spots are not that rare and can be accompanied by other serious issues, like your image fading to black after you’ve turned the TV on.

We offer repairs as well as a vast range of products so, if you find that your current TV is well past its sell-by date, be sure to browse our amazing

The difference between a LED TV and a LCD TV is that they are both LCD TV’s except one has LED stripes and the other has CCFL Backlights- (Florescent Tubes). I used a Philips Magnavox Emerson LG TV when testing these repaird, but they should work on other TV brands that are similar. Before you do any Repair, check to see if you are still under warranty, or are covered by a recall of your TV!!

If your Plasma or LCD/LED or CCFL/LCD TV or monitor has stopped working, or is displaying one of the following symptoms, then it *may* need some new capacitors in the power supply board or a replacement board

-Upon three unsuccessful start up attempts the TV locks itself in protection mode and needs to be disconnected from AC for 30-40 seconds before power attempts can be restore-Display Locks after 10 minutes–

1) the front green LED of your TV comes and stays on for 20-30 seconds, then turns off for 1-2 seconds and then keeps cycling like that, but the display never comes;

2) the display comes on for a brief few seconds, then the TV shuts off; in some models the display may not even come on, but still the relay clicking on and off and the green power LED activation and shutdown can be easily observed.

A model number is needed to determine the unlock procedure, but most likely you will need a remote to unlock most TV’s. Below is a common lock procedure.

Choose On to disable all the buttons on the front of the TV. FPA Lock On will appear on the TV screen each time you press buttons on the front of the TV. You can still operate the TV with the remote control. You can still use the POWER button on the front of the TV, but only to turn off the TV (not on). Set FPA Lock to Off to cancel this feature so you can use the buttons on the front of the TV again.

3. Press and hold each of the remaining buttons on the TV, one at a time, for about five seconds, and then release. DO NOT use the buttons on the remote control - only use the buttons on the TV itself.

6. The TV should start automatically scanning for active channels from your input signal source. Make sure you have a good signal (antenna or cable or satellite).

If the TV still does not display anything, try the menu button on the TV and see if you can access the menu. If not, try using the remote control’s menu button.

If the TV is still locked and will not respond to any commands from the front panel control buttons or the remote control unit, it is apparently locked in a failure or diagnostic mode, and would probably have to be diagnosed and repaired by a reputable TV repair facility. Good luck.

If it is a thin vertical line that appears on certain video resolution/image then it is normal and is indicated in the users manual under troubleshooting. If the line is almost half the screen, it could be a problem with the cable connection between the LCD panel and logic board, or the LCD panel itself. Try reseating the cable first if it’ll solve the problem. I’ve done similar issue in the past. Reseating the cable worked for a couple of months till eventually the LCD panel is the problem. Replacing the LCD panel is quite costly and impractical.

If the lines are there all the time or intermittent but in the same location it is an indication of a bad panel. The panel driver can also be the cause of this symptom.

If the lines/bars are across the OSD Menu, and all the video signal inputs also same result, that means the TV LCD Panel is defective Most of the time this symptom is caused by a bad LCD Panel 95%. You can try refitting LVDS Cable or replacing Main Board capacitors or replacing Main Board—5%

Bad news unfortunately, their are two possible causes for what you have described, one would be a fault with the picture drive pcb ( Power Control Board ), and the other is physical damage to the LCD cell matrix, (screen).

There’s videos on how to fix this. It has to do with putting foam, in between panel frame and screen, which applies pressure to solder joints, which then completes the circuit- Contact my10cents, for better explanation.

Big Black Bar on bottom of TV Screen– If the bar that appears in the bottom is showing the energy saving logo, HDMI, Dolby surround and pc mode capabilities look into your remote.

Is the OSD menu affected as well? If yes then possibility could be the LCD Panel or the t-con board. Since you have replaced the t-con board then possibility is the LCD panel. There could be also a possibility of mainboard where upgrading the firmware could restore the picture. If the OSD menu is not affected then the LCD panel is good.

If the lines are across the OSD menu then chances is very high the LCD panel is the cause of the problem otherwise it can be due to bad T-con board or even Mainboard. Have you tested on the OSD menu to see if the lines are really across the menu?

White Lines– There are several possibilities that can cause white lines on an lcd screen. One would be high temperature on the logic board. Logic board drives the LCD panel and when it overheats can cause this display problem. One solution would be to clean the vent holes around the TV. One possibility that I have experienced myself servicing is a bloated capacitor on the power supply board. The worst possibility is a defective LCD panel, which is costly to repair, and sometime more practical to buy a new TV set.

Do you get blue screen when using x-box or DVD, VCR? Have you tried to reset cable box if you have one? Reset TV. Check all cable connections? Try these first.

Do you use the Set top box for cable channels? If yes then try connecting through HDMI and see if you can see the TV. Also do you get blue screen when using x-box or DVD, VCR?

What made you decide to change the mainboard? I ask because if the MENU does not appear, then this indicates a problem elsewhere within the TV. Also, did you check for any swollen, or bulged capacitors on the power supply board?

There are several problems that could cause this problem. It could be the connection from the T-Con board to the panel, try wiggling these cables around and see if the picture comes up even for a second. The Mainboard or it’s cables are not the issue in my opinion. The isdsue is either going to be a bad capacitor, faulty output from the power supply to the T-Con board, a bad connection from T-Con to panel, or the T Con or the panel itself are faulty.

Basic things you can do is to check the connections. If you have a cable box, check the video connections. And while doing that, unplug the TV and the cable box from the AC outlet for it to reset. These are the most likely cause of a blue screen

Most of the new TVs display a blue screen when theres no signal for it to lock on. Try unplugging it for about 5-10 minutes and see if that clears up the problem. Why? Because they have microprocessors in em (computer chips) and just as like with any other operating system, they can hang up or crash. This isnt an uncommon problem with todays TV sets. Unplugging it for awhile resets the microprocessor (in other words, it causes it to re-boot when you plug it in again).-

It could be the connection from the T-Con board to the panel, try wiggling these cables around and see if the picture comes up even for a second. The Mainboard or it’s cables are not the issue in my opinion. This is due to either a bad capacitor, faulty output from the power supply to the T-Con board, a bad connection from T-Con to panel, or the T Con or the panel itself are fault. Also, it’s possible the A/V receiver’s Video On feature was turned off by an electrical surge or something else.Turn the Video feature back to On and suddenly that bad blue screen was gone.

Repair/Solution: Change the cable box to a fixed resolution. OR have the customer install the latest TV firmware which can be located at your TV Brand Customer Support

Your power board needs serious help–If you want to repair you have to replace Switching Mosfets, disc capacitors and of course the main fuse, Rectifier Diodes and most of the time the transformer–Costly–Easier to replace Power Board–There is a chance the strike come through the cable line, so it’s possible the Main Board needs repair–That’s a small chance though, but I thought I’d let you know–Replacing power board should repair your TV. During a lightning storm, electrical power surges is induced to the transmission line eventually end to our household appliances. Our TV sets, computers are the most susceptible. For the TV set, the basic cure is to leave the TV unplug from the AC outlet for it to discharge and reset

5. wait another 30 seconds and some type of picture should appear—If that does not work–Unplug TV for 10 minutes and then hold power button on TV for 60 seconds–Plug in and turn on.

Unplug TV– On TV, hold the power button down while pushing and holding each button for a few seconds. After going through all buttons, (on TV) then plug TV back in and it should power up–

When the TV, has no Picture or Sound. Led turns from red to (Blue or Green). It means the Main Board has sent out the start up signal to the PSU (Power Supply) Board.

Now we need to know if PSU Board has all the correct output voltages. This means checking the secondary side output voltages of Power Board. Probable causes are the Power Supply, the T-Con board, Main Board or the LCD panel itself has failed.

No Picture/Sound The person who looked at my TV, stated that the high voltage power supply needs to be replaced. He explained that I have a low voltage supply which is why the power button is lit once pressed, and a high voltage supply which needs to be replaced.

You will have to go into the TV and check for capacitors or burn marks or cracked solder around the pins–Main board could be IC’s, or regulators–Panel–Disconnect panel and see if your TV stay’s on—

The flashing green light indicates a fault on the power board inside your TV. This will be due to a faulty component like a capacitor or voltage regulator. Faulty electrolytic capacitors on the power board are the most common cause of this problem. These capacitors will often leak and stop working as the TV set gets older,but could also be caused by the Main Board or the inverter board. (LCD TV ONLY) So we will have to take a look inside and maybe do some circuit testing and a visual of your boards-

In a dark room take a flashlight and at an angle shine it on the screen and see if you can see any movement. If you can see movement or see your menu then its backlight failure. If totally black screen with sound then its T-Con board. So if you see movement on a led screen, then it’s your LEDs inside the panel. If on a LCD TV you see movement and lamps are not turning on, replace inverter. If with a LCD TV your lamps turn on, with no picture replace T-Con Board.

Plasma is the most durable in terms of panel failure. LED/LCD is terrible for panel failure. (But every model gets bad apples. Samsung LED/LCD panels die frequently. LG panels are a lot more reliable.) Overall I’d say plasma is more reliable, and even if it fails, in most cases plasma is repairable, LED/LCD is expensive to repair and often difficult to troubleshoot.

A blurry image on a high-definition LCD TV is typically the result of a mismatch between the TVs resolution capabilities and the resolution of the signal that is coming from connected devices, such as a DVD player or satellite TV receiver. Typically, blurry pictures result when a peripheral device connects to the TV through non HD cables and jacks.

TV repair costs between $60 and $350 with most spending $207 on average for LCD, LED, plasma, and 4K TVs; costs are higher if repairing older DLP, projection, and HD TVs. TV problems like display issues, powering-on problems, or sound issues can be fixed. Pickup and delivery fees may apply.

The cost to repair a TV will include the price of parts and labor costs, plus other associated costs. Additional charges include a trip fee for a technician to come to your home, a fee to transport your TV to and from a repair shop, and the diagnostic fee to determine what needs to be replaced.

The cost to repair a TV screen can be significantly more than the cost of purchasing a new TV. For this reason, replacing or repairing a broken TV screen is not considered feasible.

For example, the price of a new Samsung 40-inch LED TV is about $400, yet the cost of a replacement display panel for this model is about $380. This price is only for the replacement part and does not cover diagnostic costs, labor costs, or travel or shipping fees.

Broken TV screen repair is not a service offered by most TV or electronics repair companies. For example, BestBuy"s 90-day warranty, does not list broken TV screen repair as one of the problems they service.

Unless you are trying to fix a TV from the ’80s or earlier, cracked TV screen repair is not feasible; the entire display panel must be replaced instead. The cost of a replacement TV display panel is more than the cost of buying a new TV, and that’s before labor and other service costs.

The cost of TV screen replacement is generally the same as or more than the cost of buying a new TV. Therefore, replacing a broken or malfunctioning TV screen is not considered a viable option. If the TV is under the manufacturer’s warranty, the manufacturer may replace the entire unit.

TV manufacturers do keep replacement TV screen panels on hand to support products under warranty in case the screen malfunctions, due to manufacturer defect.

If you still want to replace a damaged or malfunctioning TV screen, your best option is to find a used replacement panel or a broken TV of the same model on which the screen is still functional. You might find one on eBay, and you can hire a technician to change out the panel.

The cost of a used replacement TV panel ranges from $50 to $350 or more, excluding shipping, depending on the brand and size. Note that the chances of finding exactly the part you need in excellent condition are slim, and the cost excludes the cost of installation by a repair shop.

Whether your TV is LCD, LED, plasma screen, or 4K (Ultra HD), the cost to fix common problems ranges from $60 to $350, depending on the repair type and the brand of TV being repaired.

These repair problems could have more than one possible source, so a technician should take time to narrow down the exact problem. TVs are repaired by replacing faulty components.

TV motherboard replacement costs between $200 and $350, including parts and labor, or about $275 on average. Motherboard replacement parts range from $35 to $199and labor costs from $60 to $125.

A TV inverter repair costs $104 to $171, including parts and labor, with an average cost of $138 for a TV with one inverter board or $178 for two. Parts range from $7 to $74, and the average labor cost for TV inverter repair is $97 per hour.

The function of an inverter board in a TV is to power the backlight of the screen. The inverter board requires a few hundred volts of power. If the inverter board goes bad, this would cause the TV to power on and have sound but no picture.

When an inverter component goes bad, it is usually replaced rather than repaired. In some cases, the capacitors on a converter board fail, and a technician can fix it by replacing the capacitors rather than replacing the entire inverter component. However, if an entire inverter board replacement is not available for the model of TV being repaired, replacing the capacitors may be the only option for TV inverter repair.

A flat-screen TV bulb replacement costs between $60 to $115, with most homeowners spending $84 for parts and labor. The price for replacement bulbs ranges from $18.50 to $80.

If an older model LCD TV or projection TV powers on and has sound but no picture, this may be due to lamp burnout, which is both common and expected. In this case, replacing the bulb will fix the problem. An experienced technician should be able to replace the bulb quickly and easily.

TV backlight repair costs $100 to $122, including replacement parts and labor, at a repair shop. In-house repair costs are more due to trip fees. The price of backlight replacement parts averages around $2.50for each LED and between $20 and $25 for each CCFL strip.

If the CCFL strips for your TV are no longer available, a technician can convert the backlight from CCFL to LED using the same number of backlighting strips. Each strip of LEDs costs between $12 and $30.

Backlight failure in a TV may also be due to failure of the power inverter that supplies power to the backlight. In rare cases, both the inverter and the lighting components fail.

Repairing a TV power supply board costs $23 to $234 for parts alone. Completely replacing the power supply board costs $250 for parts and labor. If one capacitor has failed, the cost for replacement capacitors is low. However, it’s more cost-effective for the technician to replace the entire board rather than spend time trying to diagnose and replace faulty capacitors one by one.

The cost to fix an HDMI port on a TV is $93 to $302. In some cases, the input circuit board that the HDMI port connects to may be damaged and need to be replaced. The cost for replacing this input circuit board, including labor, ranges from $200 to $350.

TV capacitor repair costs $60 to $129, including parts and labor. The cost for the replacement part ranges from $0.06 to $14, with the labor portion ranging from $60 to $125 per hour. TV capacitors protect the circuit from getting too much power, filter signals, and facilitate changing channels.

It is not possible to fix a TV capacitor when it fails; it needs replacing. If your TV stops working while you are using it and you notice a smell similar to ammonia or bleach, this is a sign that a capacitor has blown. However, some capacitors do not make any noticeable smell when they blow.

Flat screen replacement glass is not available. The only option for flat-screen TV glass repair is to try optical glass glue, which costs $1.70 for a 5-ml. tube. This may be an option for TV glass repair if the crack is only a few inches or less. TV panels are built as one unit at the factory, with the glass adhered to the display panel.

In-home CRT repair ranges from $199 to $249. The cost of repairing a CRT picture tube ranges from $199 for a TV that is 27 inches or smaller to $249 for a TV that is 28 inches or larger.

Picture tubes, or cathode-ray tubes (CRTs), were used in old TVs, which had much poorer image quality than modern TVs and were much bulkier and heavier.

A TV fuse repair costs between $61 and $136, with most spending $99 on average. The cost of the replacement fuse itself is $1.50 to $11, while labor ranges from $60 to $125 per hour. Additional fees may apply.

LCD flat-panel repair is not considered cost-effective. If the glass is cracked or the display is physically damaged, it is cheaper to replace the entire TV than to repair or replace the display panel.

Estimating TV repairs costs by brand is not something TV repair shops offer, however, there are general prices by type. When looking for specific repair costs for your TV, you’ll find them in the common repairs price list above. Pricing applies to brands such as Samsung, LG, Sanyo, TCL, Insignia, HiSense, Sony, Toshiba, Pioneer, and Vizio.

More popular TVs are usually less expensive to repair because repair shops order replacement parts for them in bulk, which allows them to buy those parts at a lower cost.

The cost of flat-screen TV repair ranges from $42 to $359. You cannot fix a broken screen, but the price of a new flat-panel TV starts from around $249 for a 1080-mp (non-4K) LED TV from LG to as much as $14,999 for an 85-inch 8K LED TV from Samsung. A TV referred to as a “flat TV” or “flat-screen” TV might be any of the following:

LCD TV repair typically costs $60 to $85 for diagnostics testing, and $200 to $300 to perform repairs. LCD TVs use backlighting, which may fail. Newer LCD TVs use LED strips for backlighting. Older ones might use CCFL. If CCFL backlighting fails, a technician can replace it with LED backlighting.

An LED TV is just an LCD TV that uses LED backlighting, which all newer models do (older models use CCFL backlighting). The cost to replace one LED backlighting strip ranges from $100 to $122, including parts and labor.

The cost to replace the motherboard, inverter, or LED"s in a 4K TV ranges from $100 to $275 or more depending on the brand and model. The cost for screen repair for a 4K TV is irrelevant because it cannot be fixed or replaced at a cost that is lower than the cost of a new 4K TV.

Digital light processing (DLP) TVs are also known as projection TVs. DLP big screens have not been made since 2012, and DLP TV repair is usually not worth the cost except for a lamp burnout, in which the bulb can be replaced. The cost to replace bulbs ranges from $60 to $115.

TV repair shops charge an average $60 to $125 per hour, or a flat rate of $50 to $250, which includes the diagnostic fee. Additional costs after that depend on the repairs needed and the brand and type of TV. However, most stores will have a minimum charge of about $90.

Best Buy TV repair is provided through the Geek Squad TV & home theater service. Geek Squad TV repair starts at a base cost of $100 for a diagnostic fee. TV repair is covered under Best Buy’s protection plan, which costs $280 per year when you purchase a TV from Best Buy at the time of purchase, or within the return period printed on your receipt.

The brand and model of your TV will dictate the final repair cost, with more expensive brands and larger TVs costing more to repair. Consider the remaining lifespan of the TV before paying for repairs. You can now buy bigger TVs with more features and better displays for a TV that won’t need repairs for a while and probably comes with a warranty.

The cost of labor to fix a TV ranges from $60 to $125 per hour, or a flat rate of $90 to $299. If the work is performed in your home, the cost ranges from $25 to $125 per hour plus the trip fee. Most TV repairs take 1 to 3 hours if the repair specialist has the parts already.

Some shops will pick up and deliver a TV for free. Others charge a fee that ranges from $40 to $75 for pickup and drop-off, with an average cost of $58.

If you live in a remote area, you may need to ship your TV to a repair facility, costing $99 to $175. Be sure to choose a delivery service that allows you to track the shipment and confirm delivery. When sending your TV into a service center for repair, you will be contacted regarding the associated costs and asked to process payment before the repair is completed, which usually takes two weeks including the shipping time.

Many TV repair shops charge a diagnostic fee that ranges from $20 to $60, depending on whether it is done in your home or the repair shop. Some shops charge a flat fee that ranges from $50 to $250that covers both the diagnostic cost and labor cost. In many cases, the initial diagnostic fee will be applied to the repair cost if you have the shop do the repair.

The more expensive a TV is, the more sense it makes to purchase an additional warranty to defray the potential for costly repairs. Best Buy offers an $89 five-year extended warranty for entry-level TVs. On larger TVs such as the 85-inch Samsung QLED 8K TV, which costs $14,998, the five-year warranty from Geek Squad costs an additional $1,699—11.33% of the cost of the TV.

With modern TVs, repair entails component replacement or replacement of capacitors, for which high levels of certification are not necessary. Generally, TV repair shops will let you know if their employees have certification.

The cost of mounting a TV ranges from $149 to $199, with most people paying around $174 for the labor. The mounting hardware costs between $20 and $500 depending on the brand of mounting hardware and the size of your TV.

There are various ways you might be able to save money on TV repair. These include transporting your TV to a repair shop, using a shop that charges in 15- or 30-minute increments, diagnosing the problem yourself, using salvaged parts, and doing the repair work on your own.

You can also consider the cost of TV repair when purchasing a new TV. More popular TV models are less expensive to repair because repair shops buy parts for the most common TVs in bulk and are therefore able to get them at lower prices.

Plug - If the TV is not powering on and no status LEDs are lighting up, start by plugging the TV into a different outlet. If the TV is too challenging to move, you can run an extension cord from another nearby outlet.

Circuit breaker - Check the circuit breaker for the power outlet that the TV plugs into. You can check the breakers by opening the door to your breaker panel and looking for circuit breakers that are in the OFF position.

Power cable - Check the power cable. If it is a removable cable, you can test it by substituting a power cable from another piece of equipment in your home, or you can buy a replacement cable for this test. The cost for a replacement TV power cable ranges from $2.50 to $10.

Remote control - If the TV is not powering on with the remote control, you should try replacing the batteries. For remote controls with a status LED light, there could be enough power to light the LED but not enough power to send a signal to your TV.

Inverter is bad -It is possible that the inverter, which powers the backlights, has gone bad and needs to be replaced. It’s also possible that one or more capacitors on the inverter have gone bad, in which case a technician may be able to replace capacitors more cheaply than replacing the entire inverter.

Lamp burnout -In a projection TV or older LCD TV, no picture may be caused by lamp burnout. In this case, a technician can replace the bulb quickly and easily.

Plug headphones into the headphone jack. If sound comes from the headphones plugged into the headphone jack, this indicates a problem with the TV speakers.

The primary way to save money on TV repair would be to perform the work yourself. This may require you to purchase and get familiar with various tools such as soldering tools, and methods for replacing a capacitor or some other component.

The right parts - It can be complicated to determine which component of a TV is failing and causing the TV not to work correctly. If you buy a replacement part and perform the repair yourself, the TV may still not work, either because you replaced the wrong part, the part was old and not working properly to begin with, or you did not perform the work correctly. Buying multiple replacement parts can become costly.

Lack of experience – you might cause more damage to the TV due to your lack of knowledge and experience, and you might also end up causing a fire with your soldering iron or being electrocuted.

The cost of repairing a TV could be as much as $500 if multiple repairs are needed. Consumer Reports recommends not to spend more than 50% of the cost of a new TV repairing the old one.

If you have a newer TV that cost thousands of dollars, having it repaired would most likely be cost-effective. If the TV only cost a few hundred dollars to begin with, replacing the TV is more likely to be the best option.

Not included in these prices from Best Buy are 1080P screens, which range from $249 to $279 for 43-inch TVs from brands like Samsung, Sony, and LG. On the upper end, Sony and Samsung both have 95-inch 8K LED TVs for $69,999.

In most cases, a flat-screen TV can be fixed. The exception is a physically damaged display panel or screen. Most other issues including failing speakers, backlights, or power supply. Burned out fuses and damaged input ports can also be repaired.

If the screen is not physically damaged but is not showing a picture or is displaying “snow’” or vertical or horizontal lines, a technician can repair the TV by replacing failed components. If the screen is physically damaged, it cannot be repaired.

You cannot replace a broken flat-screen display. New TVs costs anywhere from $249 for a 1080P (non 4K) LED TV from LG to as much as $14,999 for an 85” 8K LED TV from Samsung.

Some shops will pick up and deliver a TV for free. Others charge a fee that ranges from $40 to $75 for pickup and drop-off, with an average cost of $58.

If you live in a remote area, you may need to ship your TV to a repair facility, costing $99 to $175. Be sure to choose a delivery service that allows you to track the shipment and confirm delivery.

However, if the digitizer or LCD is also damaged during a fall, that screen no longer carries value because it cannot be refurbished. Repair shops cannot sell broken LCDs to refurbishing companies; therefore, they cannot offset the cost of an LCD repair. That is why repair stores often charge a little extra if there is damage to the LCD or digitizer, to make up for that loss. Repair stores that don’t have an additional charge for an LCD repair typically inflate their glass repair price to make up for the loss from damaged LCDs. If they have one price, that means everyone is paying more to cover the cost of customers who have damaged LCDs and customers who only have cracked glass. This is why TCR separates the price of glass and LCD repairs for you! If you only have cracked glass, you only have to worry about paying to replace the cracked glass.

If your phone or tablet’s glass is shattered there will be cracks or chips on the screen itself. If it is just the glass that is damaged, the device may still function and you may be able to use it normally. If this is the case, it is likely that only the glass needs to be replaced. To prevent further damage to your device it is best to get it repaired quickly. For example, if liquids seep through the cracks it could cause permanent damage to the LCD.

Many people may continue to use their touchscreen with shattered glass and delay fixing the glass on their devices; however, if the touchscreen isn’t responsive, it could be a sign of more significant damage to the device’s digitizer which is integrated with the LCD screen.

A pixelated screen can indicate LCD damage. This would look like a patch of multicolored dots, a line or lines of discoloration, or a screen with rainbow colors. For many people, these colors are an easy way to know that their LCD is broken and that they should get it repaired.

Dropping your phone isn’t the only reason you’ll end up with a pixelated screen. Over time, your screen’s LCD may break down through regular use. This happens to other devices aside from your smartphone or tablet. Pixelation can happen to TVs and computers, too. People typically decide to buy a new device when this happens. Fortunately, with an LCD repair, you can fix the device without needing to replace it.

A black screen or black spots on your smartphone or tablet is an indication of a damaged LCD. Often with a bad LCD, a phone may still turn on and make noises, but there is no clear picture. This does not necessarily mean any other part of the phone is damaged and a simple screen replacement will get it functioning again. Sometimes it can mean a battery or other internal component is damaged. It is best to have a highly qualified phone repair technician diagnose what is wrong so the appropriate repair can be made.

Fortunately, your mobile device is fixable whether you cracked the glass or damaged the LCD. Stop by or call TCR: Triangle Cellular Repair at (919) 263-2699 for a free diagnostic and quick, affordable cell phone repair in Chapel Hill and surrounding areas. We’re always happy to help!

Repairing your TV can be a little tricky, but with the right diagnosis and part number(s) and a few tools, almost anyone can fix their TV and save money. We"ve helped everyone from kids (with some adult supervision) to grandparents successfully repair their TVs! Now it"s your turn -- here are some tips to help you get started on your TV repair journey.

An accurate diagnosis is the first step in fixing your TV. Once you figure out what"s wrong with your TV, you can narrow down the defective part(s) that"s causing your TV"s symptoms. A quick Google search of your TV model number will help you figure out if your TV is an LCD, LED or Plasma model. Once you know your TV type, use these videos as general guides to help you properly diagnose and repair your TV.

DLP TVs can be difficult to move around, but they"re relatively easy to diagnose and fix. In this section, we list our popular DLP repair videos by part and brand.

We always, always recommend searching by part number. It"s okay to start searching with your TV model number, but the most efficient way to find the exact replacement TV part for your TV model is via part number. If you need help searching our website, please visit our Help Me Search page.

If you’re worried that your LED TV is dying, then you’re not alone. Blinking, flashing, blurred lines, and a variety of others symptoms might be a sign that it’s time to get a replacement. Fortunately, you can fix a lot of problems without getting a new one. Nevertheless, it’s important to know when something’s wrong.

The signs and symptoms of a dying LED TV include dull, faded, blinking, lined screens and delayed communication services. Other problems include distorted colors, dead pixels, and burn-in edging. Although it’s rare, another symptom includes high-pitched noises from the screen.

Perhaps the most impressive part of owning an LED TV is that they do everything almost instantly. The remote communication responds immediately, the pixels brighten up with color, and the images are crisp. Unfortunately, this makes it very easy for you to notice small issues, such as a long wait time.

If you turn on the TV and it takes forever, it could be a remote issue. The signal needs to be strong and unblocked. However, it’s typically a symptom of a dying LED TV. The pixels aren’t able to respond to the command, which leaves them looking worn and dull.

When you turn on an LED TV, you should expect high-quality images that show up instantly. If you’re getting anything other than that (as you’ll see throughout this page), it’s a huge sign that you need to get it repaired or replaced. Since TVs are heavily sealed these days, it can be hard to DIY the repairs.

Nobody wants to look at a dull TV screen. The biggest reason that people want to invest in an LED TV is that they want the vibrant, bright, detailed images promised by countless companies. Unless the TV has a low pixel count (which is very rare with LED screens, especially those produced within the last five years), then you might need to get a new one.

Dying color bulbs could be a huge cause of a dull screen. This could be a result of an old screen. LED bulbs are designed to last for a very long time, but like all other TV screens, they won’t last forever.

When someone runs into the TV, knocks it over, or hits it with something sharp, it could break or damage the bulbs. This process leads to a dull screen since it’s nearly impossible to repair the inside of modern TVs.

Sun fading is no joke. If your TV is positioned in direct sunlight, it can dull the screen quickly. Much like sun bleached clothing, LED screens are capable of being dulled and having their colors stripped.

Have you ever started watching TV and it suddenly shuts off? Fading is also a common issue. Both of these problems are associated with a TV that’s on its way out. If your TV is always faded or randomly cuts to a much lower resolution, then it’s probably not going to see life much longer. You’ll need to get a new set within a few months.

The good news is that, if you don’t mind it, you can stretch the lifespan of a faded TV for a long time. The biggest issue is when it starts to randomly fade and turns itself off. If this issue occurs, then there’s not much you can do. It’ll continue to fade and shut off more often until it doesn’t last more than a few seconds.

If you catch the error when it starts, you might be able to save it. There are plenty of TV repairmen that claim that they can handle the problem. You might be able to spend $50 to $100 instead of the thousands required to replace large, top-of-the-line LED TVs.

Similar to the previous sign, if your TV blinks randomly, you might have a serious problem on your hands. It could seem like a blink sometimes. Many people miss this issue because it’s so sudden and random that they mistake it for a flickering light. You’ll notice that it happens more often, which is when you need to get it fixed.

Much like a faded screen, you can have it fixed if you catch it in its early stages. Failure to do so will cause the TV to shut off, become discolored, or completely die. Blinking is caused by dying cells or flickering LED bulbs. The more bulbs that fade out, the more blinking you’ll have. Keep in mind that the blinking could be concentrated in one spot or spread throughout the TV.

Although it’s not as common, the blinking might occur around the edges of the TV. Since the bulbs are sometimes put under pressure near the sides, top, and bottom of the screen, improper placement could cause them to lose power much sooner than they should.

You might also notice flashing in one spot of the screen. These concentrated bouts of flashes, blinking, dulling, and similar issues can be a sign that the cells of your TV aren’t looking too good. They’re a telltale symptom of a dying TV, regardless of if it’s an LED or any other type of television set.

When you see these flashes, it’s time for a new TV. it’s very rare that you’ll be able to fix this issue. Fortunately, most high-quality LED TV screens are designed to last for many years without any signs of this once-common problem.

Most modern TVs have built-in speakers, especially high-end LED sets. If the speakers start to fail, it means that the TV is on its way out. There are several causes of failed sound quality, including the following two issues:

Playing the sound too loudly through the speakers will cause them to blow out. Many people have heard about playing speakers with too much noise, ruining the internal components. LED TVs aren’t immune to such issues.

The remote or on-screen buttons aren’t communicating with the TV. These problems can be fixed by dealing with the remote or the receiver. You usually don’t have to buy a brand-new TV, in this case.

Rent a Center explains that screen burn-in is one of the biggest issues of owning an LED TV. While it’s rare, an LED TV can experience this symptom that shows fading around the edges of the entire set. It’s known as a ghost image for many reasons, mainly due to the dull images that remain from previous channels.

For example, if you always watch the news, the logo might be ‘burnt’ into the bottom corner of the screen. It maintains the same image, even if you switch channels. You won’t likely see the colors, but the outline can be seen whenever you have the TV turned on. There’s not much you can do since it’s irreversible.

One way to prevent this problem from happening is to ensure that your TV isn’t on all day. We’ve all had the habit of leaving the TV on when we go to school or work. However, long-term misuse can cause it to overheat, burning the image onto the screen.

This symptom is the most obvious issue that it’s time for a new TV. Whether the crack shows up on the screen or the edge of the plastic, it can’t be repaired. To make matters worse, LED screens are known for spreading cracks very quickly. Even if it looks small, a few bumps can cause the crack to become bigger.

The good news about cracks is that they’re often covered by manufacturer warranties. That doesn’t include if you throw a rock or even a Wiimote at the TV, but you get the point. If the set arrives with a crack, then you’ll be able to contact the company to get a repair or replacement. Make sure you ask about warranties and guarantees before you buy a new TV.

Every TV screen is made out of a series of pixels from end to end. If you don’t know it already, the resolution is composed of these pixels. For example, modern 4K UHD TVs are made of over 3 million pixels. The more pixels there are, the higher the resolution and the clearer the image will be.

Unfortunately, damaged pixels start to form lines. You’ll notice that the pixels are bigger in some spots than others. When one pixel breaks or goes bad, it could spread to nearby pixels. Electronic World TV shows us that this issue is far more common than you might think. To make matters worse, it’s very difficult to fix.

Much like the other problems on this list, lined pixels are a result of misuse. When people throw things at the TV (I’m looking at you Wii and Switch owners), drop it on the ground, or expose it to too much sunlight, the pixels become damaged. You might notice lines, bumps, and clusters.

An LED TV’s signal is a major part of its function. Nobody wants to have to stand up and walk over to the TV every time they want to change the channel. In fact, a lot of new TVs aren’t made with channel buttons aside from the remote. If your set isn’t communicating or responding to the commands, there’s no purpose in owning a TV.

Thankfully, this issue is one of the few repairable symptoms. It’s usually a matter of getting a new remote, replacing the batteries, or fixing the TV’s receiver. All three of these problems are relatively inexpensive, especially when compared with the cost of a brand-new LED TV. You can test the theory by replacing the batteries, then moving to the next suggestion.

The downside of this error is that it’s not always able to be fixed. If it’s not the remote, batteries, or receiver, then it might be the LED screen. The bulbs don’t want to turn on because they’ve been permanently damaged. In this case, it’s time for a new TV.

Nevertheless, it’s worth hanging onto the TV until you find out if it can be fixed. Call a TV repairman or call the manufacturer to figure out if they have any recommendations. That suggestion applies to any of the signs and symptoms of a dying LED TV.

Overexposure to bright lights (whether they’re natural or artificial) can cause the screen to lose its brightness. Another common cause is that people tend to turn up the brightness on their TV too often. If you’re used to adjusting the lights in your TV, then consider that it could be causing permanent damage.

Remember that blurriness or fuzziness could be as simple as a bad TV signal. It’s not always the fault of the LED TV, so you might want to consider the typical connectivity issues in the area.

Low-quality LED screens don’t have the same cutting-edge technology and protective features. If you cut corners and tried to get a budget-friendly TV, then there’s a chance that the screen wasn’t installed correctly. The result will be a warped, wavy TV screen. You can notice it better if you look from the side of the set.

Another cause of warped, bubbly LED screens is when they’re exposed to too much heat. There’s a lot of plastic used in the production of TV sets. Whether you’re leaving it on for too long or exposing the screen to excessive amounts of sunlight, it could start to ripple. It looks worse as the months go by.

There’s no way to fix a warped LED TV screen. If you notice it, then the best bet for a longer-lasting TV is to remove the heat source. On the other hand, those who got the warped screen issue right out of the box should contact the manufacturer to request a warranty repair or replacement.

If you’ve ever noticed a high-pitch hiss or crackling sound coming from your TV, there could be all sorts of causes. One of the most common issues is when you turn the brightness too high. The bulbs will be maxed-out, ruining the image. If you have a low-end LED TV, this problem is much more likely to occur.

The sound could be coming from the internal components of the TV, though it’s unlikely. Again, low-quality sets have a host of problems that are unexplainable and frustrating. The best way to prevent any of the issues on the list is to get a high-end, manufacturer-backed LED TV.

Note: Hissing or crackling from a power strip or plug from your TV is a safety hazard. Turn it off and unplug everything. Examine the power brick and the outlet to ensure that you’re not overloading anything.

As you can see, there are plenty of signs that you need to keep an eye out for when you’re owning and maintaining an LED TV. Sadly, most of these symptoms are the start of an irreparable deterioration process. Most of them are avoidable if you practice safe TV usage suggestions.

Ever had your TV showing nothing but a black screen even if the audio was working? Unfortunately, that’s a common issue with low/middle-end LCD/LED TVs these days… Even more frustrating, this issue often comes from a rather tiny and cheap component that can be easily replaced. Most common issues are:

One of my relatives had this exact symptom happening all of a sudden. This problem on low-end TVs often occurs within the first couple years. As the repair costs for that kind of TV is pretty low, considering repairing it yourself might be a good idea!

That implies disassembling the TV to access the backlight which is between the LCD screen in the front and the boards in the rear. In my case, with a Samsung F5000, I had to process as follows:

First we have to remove the back housing to reveal the boards (from left to right: main board, T-CON, power supply) and disconnect the LCD panel from the T-CON board.

Note: Older TVs have neon tubes for backlight, which is thicker and less exposed to this kind of failure. LED backlight is the most common thing these days, but do not mistake an LED TV with an OLED TV. The first one is a classic LCD panel with a LED backlight, whereas the second is an OLED panel that doesn’t need any backlight as it is integrated in each pixels (making the spare parts much more expensive by the way).

For starters I’ll go with the third one, just to make sure there is no other issues with the TV, but afterwards it’s better to replace the LED with a new one, otherwise you might notice a darker spot on the image.

Once we have by-passed the LED, we can power the TV on. Careful! High voltage (200-300v) runs through the TV when plug, so be very careful how you handle it so you don’t electrify yourself!

Now we just need to unplug the TV, replace the LED with a new one and put everything back together. Just to be sure, we should power the TV back on and check that everything is fine.

There might be a lot of other root causes for similar symptoms, a black screen often looks like something very serious and therefore expensive to repair, but this case is the perfect example that taking some time to look for the root cause can sometime lead to a good surprise: here a 1$ fix!

LCD’s do have many replaceable parts and have higher probably of repair than the old CRT box monitors. In Most cases a failed or broken Laptop Screen is worth the repair.

The AC Adapter can be easily tested with a multi-meter. This test is usually 90% conclusive if the AC adapter is good or bad. Also if the LCD has absolutely no power, no power light, no faint display, no reaction at all, the AC Adapter is a likely culprit. A quick multi-meter test can usually be done for free at most repair centers.

This is an internal part that inverts power to the needed amount for the backlight and panel. Inverters fail, and can be easily replaced. Failing inverter symptoms:

The backlight usually is simply a miniature compact Florescent light bulb. Just like what’s in office ceilings but very thin and small. This can fail like any light bulb and can be easily replaced.  Newer screens are LED and work differently.  Failing Backlight symptoms:

The panel itself can fail. The panel contains thousands of tiny pixels all connected by a mesh of thin signal cables. When a panel discolors or fails, the entire panel needs to be removed and replaced. This is less common, and is only sometimes worth the repair. Failing Panel Symptoms:

What if I break my panel? This is rather common on a laptop. Almost always its worth fixing. Usually can purchase a new panel or pull from a parted out laptop.

Other Failures. This can be anything from bad controller board or bad internal cable. These items should be diagnosed by a professional. A simple cable issue can be $5 part. Bad board might be a time to buy a new screen.

In all cases, it might be worthwhile to fix your LCD, especially on a laptop. Although with a few year old desktop LCD, you may consider a replacement, especially if you’re thinking of an upgrade.

Ours is a Sony Bravia that is now over 10 years old. Several months ago we started noticing lines, especially on the left (our left) side of the screen. They’d go away after the tv warmed up. Then we started noticing it was darker on that side of the screen, but again, after the tv warmed up the screen would be normal. Then about two months ago it started getting worse and didn’t ever get completely better, even after the tv warmed up. So I watched some youtube videos that all talked about the ribbon cables becoming loose over time and to apply pressure along the top and see if that made it better, and if so, it was a loose cable and if you put electrical tape or something that would help keep the pressure, it would fix the problem. Hubby pressed along the top and sure enough, when he pressed in one spot on the left side suddenly the picture cleared up. Stayed good for about a week, then problems again, pressed again, fixed again. A week or so later, same problem, but this time when he pressed on it nothing got better.

So I decided to take the cover off and look at it better. As I was pressing on the tops of the ribbon cables that run down from the top of the frame, for a minute it got better but then suddenly there was a wide white vertical line, with a thin green one down the center of it, running down the front of the screen, and it was perfectly aligned with one of the cables. So now I still have the dark side of the screen, and some ghosting, and some lines, but now this bright white streak/line right down the front. Another weird thing is that if the whole screen is bright (like watching a show set in a snowy place) then the darkness even on the left side is basically gone, but if the scene is dark at all, that side is almost black. I don’t know if it means that particular ribbon cable is bad, or if something is loose, if things need to be replaced or what. It’s very frustrating as it’s been a great tv. Hubby wants to just buy a new one, but even if he does I would still like to try and figure out this one as it could then go in another room.

I had this problem too... and fixed it in about 10 min. I searched the internet for this problem and found many forums with pretty much the same resolution... REPLACE TV. I find it interesting that in almost every single case I read over the last 24 hours... no one... absolutely no one recommended a simple Problem Determination (PD) procedure to quickly determine if the issue was in the TV or outside the TV.

Supposedly people spoke to techs on the phone, which in most cases are reading from a tech manual... or try to dial in and update TV firmware remotely... what I didn"t see or read is where someone actually had a repairman look at it.. or did actual PD to eliminate issues with cables or devices connected to the TV.

I turned on my APPLE TV and switched to that as the source. I immediately noticed that the issue appeared to go away... so for grins, I tried my DVD player... and still the problem did not return...

So ... if your having this issue... BEFORE panicking from all these doomsayers on the net... that in many cases sell or repair TV ... try some simple PD ... hopefully you"ll be lucky like I was.

If your Vizio smart TV no longer works, you may need to replace its display. Before you choose a replacement screen, make sure you have the TVs model number and screen size in inches. You need to ensure the replacement unit you select is a match for your Vizio TV. Screens manufactured for one brand are usually not compatible for use with other brands. Also keep in mind that some Vizio displays come with a video card already attached.

How Does An LCD TV Work?Most flat screen TVs use liquid crystal display panels that control the light appearance on the screen. When an electric current is sent through the LCD fluid, the crystals arrange to either pass or block the light to create the image.

The source of light in these TVs is light emitting diodes or LED. LED lights are smaller and more efficient than older backlight technologies used in TVs.

There are multitude of symptoms that your smart TV may exhibit when the screen is going bad or already broken.The most obvious one would be if the screen remains dark after you turn on the smart television.

Replacing a TV screen is fairly easy task for the technically inclined. If you are unsure of your skill level, engage in a professional after you secure the replacement parts. Here are the basic steps involved in making the replacement. However, keep in mind that each make and model TV is unique and the process may differ.Lay the TV horizontally face-down on a flat, soft surface with plenty of space to work safely. Take off the back cover by removing the screws that hold it in place.

Modern flat screen TV"s have a known problem with capacitors going bad. If your LCD or LED TV won"t turn on, or makes repeated clicking sounds, there is a very good chance that you can save hundreds of dollars doing this simple repair yourself.

I know, I know. You"re thinking, "Tinker inside my LCD HDTV. Are you crazy?" No, I"m not crazy. This is a repair almost anyone can do and this fix will work for any TV.

You sit down and get comfortable, ready to watch your favorite TV show or movie. You turn on your TV and...nothing! Unsure if you hit the power button, you try again...again, nothing! But you do notice a clicking sound emanating from your TV.

HDTV"s aren"t cheap. Most of us have to save, or at least be prepared to spend $800-$1000 on new one. Heck, I"m sure many of you don"t savor the idea of spending a few hundred on repairs.

I have good news. This repair is actually quite simple, and with only a few basic tools and about 20 bucks, you can have your TV working in less than an hour.

The bad News. If your TV is physically damaged in any way, been dropped, has a broken screen or gotten wet then this repair isn"t for you. But if your TV was working one day but not the next, read on.

After unplugging everything on the TV, you will need to remove the stand. If your TV was wall mounted you will need to remove the TV from the wall, and remove the mounting bracket from the back of the TV.

The TV sits on top and inside the stand, so it wont just flop over when you remove the stand screws, but it"s always safer to have a friend hold the TV upright as you remove the screws from the stand. Then each of you grab a side and carefully lay it flat on a carpeted surface.

Above is a a picture of the back side of a typical TV. The left picture is my LG 42LN5300 and the right picture is my Samsung LN46A550, but all TVs are similar. Remove all of the screws along the outer edge of the back casing. There can be anywhere from 10 - 16 of these screws.

Then identify the "power board". Every TV is a little different, but the power board will have can shaped capacitors and is the board that the main power from the plug goes to first. On this Samsung TV I put a green rectangle around the power board that we will be working on..

The other "green" board is the "logic board", this is the computer that runs the TV. Repair of the board is beyond the scope of this article. (But it"s most likely not the problem)

Remove the screws holding the power board to the TV chassis. Most boards will have 6 screws holding them down, as does the one shown in the picture. But look it over there could be more or less.

This TV repair focuses on the small "can shaped" Aluminum ElectrolyticCapacitors.These capacitors come in many colors and sizes but are easy to find on any power board. Not only are these the most likely cause of your problem, but bad ones are simple to find and simple to replace. In most instances you will be able to visually identify the bad capacitors. You don"t need any special skills in electronics or testing.

Capacitors do not always show visible signs of failure. But, if you see either of the 2 signs above on your board, you can be confident that you"re close to fixing your TV. If you don"t see these signs of failure, but your TV had the tell-tail clicking sound, you still can be fairly certain the steps below will fix your TV.

On power board pictured above, I have indicated which capacitors you should be examining for signs of failure. These Capacitors are Aluminum Electrolytic Capacitors, and are the most likely cause of your problem. The capacitors with the green arrows are the most likely candidates for being bad, but the blue arrow are other capacitors to examine.

The pictures above are actual closeups of my TV"s board. Notice how the blue capacitors in the foreground are bulging. These are the capacitors I will replace. All other capacitors look OK. If you can find replacements for all 4 of these capacitors, and any others that show visual signs of going bad, I recommend replacing them all while your in here.

Now that you"ve identified the capacitors that look bad, turn the board over and carefully identify exactly which points on the board are the wire leads from the these capacitors.

So I took my tv apart and I think I found the problem can