stm32f4 tft display brands

This library is a professional graphical stack library to build Graphical User Interfaces (GUIs) with any STM32, any LCD/TFT display and any LCD/TFT controller, taking advantage of STM32 hardware accelerations whenever possible.

The STemWin Library is a comprehensive solution that comes with a rich feature set, such as JPG, GIF and PNG decoding, many widgets (checkboxes, buttons…) and a VNC server enabling the remote display of local displays, as well as professional development tools, such as GUIBuilder to create GUIs with a simple drag and drop.

Agreed! I will be picking one up. I’ve been happy developing for the stm32f4discovery (and other stm32 chips) with gcc, openocd and gdb. It is all free.

The STM32F4 cores are pretty well supported by libopencm3 and Code Sourcery and summon-arm-toolchain both build working toolchains and openOCD supports the stlink natively now.

A fair number of inexpensive baseboards/motherboards/accessories have also appeared for earlier versions. I hope Olimex puts out a couple nice STM32F429/427 boards.

I can see there is only a STLINK usb connector on board, so there is even no FS to expect. beside HS, I suppose does mean High Speed (480mbps). but HS anyway needs a separate physical layer USB chip for addition to STM32F4 chip and most likely this is chip is not present on this board anyway, because this is STM32F4+LCD+SDRAM demoboard and there is no need for USB at all.

The data brief bullet-points “USB OTG with micro-AB connector”. Looks like the micro-usb is on the underside, sticking out at the bottom of the photo. With matching T/H mounting tabs on the topside, labelled USB USER. But like you said, the STM32F4 requires an external PHY for HS, and it seems unlikely they’d include one on this board.

I think Farnell’s 21€ will be accurate, as ST’s suggested USD price is $24. The placeholders for the STM32F429I-DISCO on element14 (a division of Farnell) and mouser show $42, which I think predates the later ST announcement. I think the ST announced $24 will hold, and the distributor prices will match that, as they have in the past.

It’s certainly useable in any other project where you have an onboard LCD controller. Especially any other project that happens to use a STM32F4. What difference would it have made if it had an external controller? Surely it’d have been on the same PCB. Were you hoping for a removeable SPI-interfaced module?

Look in the UM1670 user manual, paragraph 4.8: the tft includes an ILI9341 controller. The ILI9341 has it’s own graphics ram inside, it is not mapped into the STM32 address space. It is connected to the STM32 via a parallel bus. The ILI9341 and similar controllers are common on cheap chinese tfts. So it is no problem to source similar tfts for your final product after developing on the discovery board.

UM1670 in paragraph 4.8 also says that “The TFT LCD is a 2.41″ display of 262 K colors. Its definition is QVGA (240 x 320 dots) and is directly driven by the STM32F429ZIT6 using the RGB protocol”. ILI9341 has multiple modes of operation including direct RGB/HSYNC/VSYNC mode which bypasses internal GRAM. I don’t have the board yet but I assume display buffer is located in external SDRAM which is also on the board. The whole point of this kit is to show TFT and SDRAM interface in new STM32F4x9.

I’ve checked this discovery board firmware available from ST’s site (“STM32F429 discovery firmware package UM1662” number: STSW-STM32138, btw. finding it is a bit difficult – ST’s site is terrible):

They are using FreeRTOS, FatFs, STemWinLibrary which is ST’s version of Segger’s emWin graphic library and STM32F4xx_StdPeriph_Driver v1.2.1 which includes F429/439 support (FMC, LTDC and DMA2D added).

Well even so that DMA2D stuff is geared towards displays with one address pointer. Try using it with displays with the x& y positions on separate addresses (like x add is 2A and y is 2B with base address of 0x6C000000 for commands and a offset of 4 for data ).. Wish there was and easy way of getting the DMA2D to work with different larger displays like the 640 by 480 of Newhaven’s http://www.newhavendisplay.com/nhd57640480wfctxl-p-2465.html

The STM32F429 Discovery helps you to discover the high-performance microcontrollers of the STM32 F4 series and to develop your applications easily. It offers everything required for beginners and experienced users to get started quickly.

Based on the STM32F429ZIT6, it includes an ST-LINK/V2 embedded debug tool, a 2.4" QVGA TFT LCD, an external SDRAM of 64 Mbits, a gyroscope ST MEMs, a USB OTG micro-AB connector, LEDs and pushbuttons.

A large number of free ready-to-run application firmware examples are available on www.st.com/stm32f4-discovery to support quick evaluation and development.

We have many years of production and sales experience, we have accumulated rich strength in the 15.6 Inch VGA TFT Display, 15.6 Inch LCD Screen, 10.1 Inch LCD Display field. Since introduced the part overseas vanguard technology and the craft and formed the powerful technical support system, it has poured into the vigor for our development. We are strict with every part of our work.

This LCD panel has a built-in EK9716BB3+EK73002 controller, a 40pin 24-bit RGB Interface, can support All View full viewing angle with IPS technology. It is composed with 10 LEDs connected 2 in parallel and 1 in serial l, with backlight voltage 16.5V/current 20mA and 16:9 aspect ratio. Optional with 4 wire resistive touch panel (RTP) and projected capacitive touch screen (PCAP.). Sharing controller board same hardware with 5” TFT LCD 800x480 resolution and 7” 800x480 resolution.