serial lcd module price

Do you need a serial LCD display? Our graphic serial LCDs and serial character LCD modules can connect and communicate with almost any host system (microcontrollers, microprocessors, PCs, etc.) and make it easier than ever to include an LCD in your product design.

LCD modules are one of the most popular components and are great for users who are looking for a more natural LCD experience, even if it is just a small bit of light. high brightness will interfere with the display of others.

A LCD panel (LCD)) is one of the most popular electronic devices that have a lot of electronic components as well, a one-time wearable LCD module (LCD), is a popular choice because it provides more numerous features to the user. compact lcd modules allow for simple components and can be used with a higher amount of power. As a result, the lcd modules allow for simple components, such as gadgets, and are used to supplement the ones that are more important.

While there are a number of wholesale lcd modules available on Alibaba.com, one may be able to find a great variety of wholesale lcd modules and kits. For consumers who are looking for suitable lcd modules in bulk, a quick search on Alibaba.com for the lcd module wholesale that is suitable for a number of wholesale components. One of the most popular lcdds bulk assembly is the lcd module wholesale that is suitable for one of the most convenient components and wholesalers.

Serial I2C LCD display adapter converts parallel based 16 x 2 character LCD display into a serial I2C LCD that can be controlled through just 2 wires. Adapter uses PCF8574 chip that serves as I/O expander that communicates with Arduino or any other microcontroller by using I2C protocol. A total of 8 LCD displays can be connected to the same two wire I2C bus with each board having a different address. The default i2C address is 0X27 and may be changed to any of the following 0X20~0X27 via soldering A0 A1 A2 pins.

This LCD module uses a 128x64 liquid crystal display that support Chinese character,  English characters and even graphics. It is suitable for interactive work with Arduino.

It features a backlit control, pallerlel or serial control, contrast adjust. It can be connect to our interface shield for arduino via IDC6 socket and Cable for Shiftout.

The LCD is shipped in Pallelel mode in default.  The R9 is used to set the interface mode. To switch to SPI mode, the R9 resistor need to be moved to R10

If you want to add some visual output to your Arduino projects, you’ll need a display. If you need only a little to display, the LCD1602 Parallel LCD Display with IIC/I2C interface is a quite good solution.RoboticsBD

This is LCD1602 Parallel LCD Display that provides a simple and cost-effective solution for adding a 16×2 White on RGB Liquid Crystal Display into your project. The display is 16 character by 2 line display that has a very clear and high contrast white text upon a blue background/backlight.

This is the great blue backlight LCD display. It is fantastic for Arduino-based projects. This LCD1602 Parallel LCD Display with Yellow Backlight is very easy to interface with Arduino or Other Microcontrollers. RoboticsBD

This display overcomes the drawback of LCD1602 Parallel LCD Display in which you’ll waste about 8 Pins on your Arduino for the display to get working. Luckily in this product, an I2C adapter is directly soldered right onto the pins of the display. So all you need to connect are the I2C pins, which show a good library and little coding. RoboticsBD

The I2C is a type of serial bus developed by Philips, which uses two bidirectional lines, called SDA (Serial Data Line) and SCL (Serial Clock Line). Both must be connected via pulled-up resistors. The usage voltages are standard as 5V and 3.3V.

If you already have the I2C adapter soldered onto the board like in this product, the wiring is quite easy. You should usually have only four pins to hook up. VCC and GND of course. The LCD display works with 5 Volts. So we go for the 5V Pin.

This is another great IIC/I2C/TWI/SPI Serial Interface. As the pin resources of Arduino controller is limited, your project may be not able to use normal LCD shield after connected with a certain quantity of sensors or SD card. However, with this I2C interface module, you will be able to realize data display via only 2 wires. If you already has I2C devices in your project, this LCD module actually cost no more resources at all. It is fantastic for Arduino based project. Specification: ?I2C Address: 0X20~0X27 (the original address is 0X20, you can change it yourself) ?Supply voltage: 5V ?The back light and contrast is adjusted by potentiometer ?Come with 2 IIC interface, which can be connected by Dupont Line or IIC dedicated cable ?Compatible for 16x02 LCD.

IIC/I2C Interface Adapter Module is used for 16×2 LCD Display.It uses the PCF8574T IC chip which converts I2C serial data to parallell data for the LCD display.Also this interface module simplifies connecting an Arduino to a 16×2 Liquid Crystal display using only 4 wires.

Very useful module to interface serial connection to parallel data, specially used for LCD displays etc. I2C Module has inbuilt PCF8574 I2C chip that converts I2C serial data to parallel data for the LCD display.

I2C modules are currently supplied with a default I2C address of either 0x27 or 0x3F, you can check which version by verifying underside of the module. If there a 3 sets of pads labelled A0, A1, & A2 then the default address will be 0x3F. If there are no pads the default address will be 0x27.

This 16 character by 2 line display has a very clear and high contrast white text upon a blue background/backlight. It also includes a serial I2C/IIC adaptor board pre-soldered to the back of the LCD. This means it can be controlled with just 2 I2C serial data pins (SDA & SCL) and so requires far less digital IO pins when controlled from a microcontroller. In total the module only requires 4 wires including 5V power and GND. Contrast adjustment is also provided by the daughter board via a potentiometer. If you plan to use this with an Arduino board you can download a compatible library and example sketch from our support forum

These modules are currently supplied with a default I2C address of either 0x27 or 0x3F. To determine which version you have check the black I2C adaptor board on the underside of the module. If there a 3 sets of pads labelled A0, A1, & A2 then the default address will be 0x3F. If there are no pads the default address will be 0x27.

If pressure is applied to the I2C daughter board it is possible for it to bend and come contact with the LCD module. Please ensure when the LCD is installed in your application that no external object is applying pressure to the back of the module.