macbook unibody model a1278 lcd panel replacement for sale

It used to be that if your screen cracked on your laptop, you"d just replace the LCD and be done with it. That unfortunately is no longer the case. With the introduction of the Unibody Macbook and Macbook pro models, Apple changed the design of the display assembly. Now, there is a glass panel assembly that is placed on top of the LCD panel. The good news is that it is possible to crack just the glass panel and save yourself some money. The bad news is that it is also possible to crack both the glass panel and the LCD.

If you take your Macbook to most repair companies with a cracked display, they"ll undoubtedly say you need to replace the entire display assembly and charge you some astronomical figure. It really isn"t an extremely difficult procedure to do yourself however, and so we"ve created the guide below to show you just how to do it.

To begin, use a heat gun to loosen the double sided adhesive strip that holds the glass in place. Use caution, and heat the glass in short segments as over heating can cause damage to your LCD.With the glass heated, place a strong suction cup on the glass and pull up and away from the glass.

Caution: When pulling up on the suction cup, you should have to exert some force. However, do not apply excessive force as this could crack your glass or LCD. When you meet resistance, heat the area and repeat. At a certain point the glass will easily come free from the rest of the display assembly. Set the glass to the side on a clean, dust free, surface.

Next, remove 4 philips head screws ( 2 on either side ) holding the LCD to the display frame. Then remove the 2 philips head screws at the bottom of the display.

To reassemble, place the LCD back in the frame, and insert the LVDS cable backwards through the opening in the bottom the display frame. Then pull the cable through the opening. You can use a plastic pry tool to assist you in routing the cable. Be very careful with this cable as it can be easily damaged.

Line the bottom of the LCD up with the bottom frame, and slide it into the groove in the bottom frame. Then make sure the 6 screw holes are properly aligned. Replace the 6 philip head screws.

- The tape on my replacement glass did not hold... I am still trying to get it to stick and imagine I"ll need to get more double sided tape or another adhesive.

I was able to do replacement successfully. (I am a puter professional ;-)..) But I have had issues with the lens replacement glue sticking well...Has anyone had the same issue and do you have a correct and pro solution? Btw....I cleaned and replaced lens correctly and new lens glue typically does not stick with any "perminance". Please advise?0

Thanks for the tutorial! But if it is too difficult, you can always sell your mac for spares to companies like www.macbookcrackedscreen.co.uk and use the money towards the purchase of a brand new Macbook :)0

I do this all day long for school districts. An opening tool like a isesame (a small metal strip) works great. As your work around the screen use guitar picks to keep the LCD to readhering (sic) to the tape. If you don"t have a plastic tool for the cable, try a small wooden kitchen probe.

Thank you very much. The LVDS cable went out on my Pro, so when i purchase a replacement tomorrow and it gets here next week, I will be using your wonderful guide.0

I broke the glass cover of my MacBook, so I ordered a replacement from PowerBookMedic.com (poor service, by the way). I tried to lift the cover using a suction cup. The cover did not come loose at the bezel, but instead it shivered into a gazillion of small parts. Removing it from the bezel was a biiiig PITA. I also used a heat gun to soften the sticky tape that held the shards on the bezel. Not good for the display...

Affected devices were sold between October 2016 and February 2018. Apple or an Apple Authorized Service Provider will service affected MacBook Pro units, free of charge.

To identify your computer"s model and to see if it is eligible for this program, choose Apple () menu > About This Mac. Eligible models are listed below.

Please choose one of the options below for service. Your MacBook Pro will be examined prior to any service to verify that it is eligible for this program.

Note: If your MacBook Pro has any damage which impairs the service, that issue will need to be repaired first. In some cases, there may be a cost associated with the repair.

The program covers eligible MacBook Pro models for 5 years after the first retail sale of the unit or 3 years from the start date of this program, whichever is longer.

OEM LCD Screen and Digitizer Assembly with Bezel for iPhone 6 -WhiteThis screen assembly can be used to replace the shattered, cracked, scratched a...

OEM LCD Screen and Digitizer Assembly with Bezel for iPhone 6 -BlackThis screen assembly can be used to replace the shattered, cracked, scratched a...

Aftermarket LCD Screen and Digitizer Assembly with Bezel for iPhone 6 -WhiteThis screen assembly can be used to replace the shattered, cracked, scr...

Aftermarket LCD Screen and Digitizer Assembly with Bezel for iPhone 6 -BlackThis screen assembly can be used to replace the shattered, cracked, scr...