5 inch tft display module in stock

ER-TFTM050-3 is 800x480 dots 5" color tft lcd module display with RA8875 controller board,superior display quality,super wide viewing angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO,and ARM .It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.

It supports 8080 6800 8-bit,16-bit parallel,3-wire,4-wire,I2C serial spi interface. Built-in MicroSD card slot. It"s optional for 4-wire resistive touch panel (IC RA8875 built-in touch controller),capacitive touch panel with controller,font chip, flash chip and microsd card. We offer two types connection,one is pin header and the another is ZIF connector with flat cable.Mounting on board by default. There is no capacitive touch panel connection on the board of ER-TFTM050-3,its capacitive touch panel needs to be connected with your external board.Now we design another new board with capacitive touch connection named_ER-TFTM050A2-3.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!".Here is the link for5" TFT capacitive touch shield with libraries,examples,schematic diagram for Arduino Due,Mega 2560 and Uno. For 8051 microcontroller user,we prepared the detailed tutorial such as interfacing, demo code and development kit at the bottom of this page.

Have your product stand out with the DT050ATFT display - our 5” TFT LCD module with full viewing angle. The full viewing angle feature allows the display contents of the LCD to be visible from practically any angle. It"s a cost-effective enhancement compared to using an IPS display. The 5" TFT has 800 x 480 RGB resolution and supports 24-bit parallel RGB input mode. The LCD uses two driver ICs to drive the display: a source driver with TCON (Ilitek ILI6122) and a gate driver (Ilitek ILI5960). It also is available with either a resistive touchscreen or capacitive touchscreen panel. This 5 inch LCD is an ideal option for a variety of digital devices including video or POS systems.

This Bridgetek/FTDI EVE development kit includes a 5" EVE display module with a large bezel. This kit is perfect for demonstrating the EVE module (CFAF800480E2-050SC-A2) or the base display (CFAF800480E2-050SC), simply plug the included Seeeduino to a 5v power source!

The included display is sunlight-readable, has extremely wide viewing angles, large color depth, and the touchscreen glass extends past the edge of the display for smooth mounting.

A wide variety of 5 inch tft lcd module options are available to you, You can also choose from original manufacturer, odm and agency 5 inch tft lcd module,As well as from tft, ips, and standard.

1. Connect this LCD to Rasp PI with HDMI cable.2. Insert TF CARD with System image.3. Connect Rasp pi to Power with micro usb cable.4. Power on.5. Wait some second,You will see the System is run!

Maclight 5 inch tft lcd display modules have 800x480, 480x272, 640x480 typical resolutions. TN TFT and IPS display modes are available. the interface can be RGB, MCU, LVDS, HDMI, mipi interfaces.

The 5 inch IPS TFT is free viewing angle tft and wide temperature tft, that its working temperature can be up to -30~80°C, one IC driver solution with cost competitive,40-pin RGB interface available,

This 3.5 inch TFT LCD Display Module for Raspberry Pi is designed to work with the RPi zero / 2 / 3 Model B / B+ and can also be used on other hardware platforms with SPI interface (Raspberry Pi showed in the picture is not included). The 3.5″ screen is the same size as the standard Raspberry Pi model B/B+, and integrates well wherever it does.

The 480 x 320 pixels resolution TFT LCD with touch screen requires no external power supply. The software package contains everything you need to start, including calibration software and virtual keyboard.

The highlight of this display module is plug and play without needing to reboot the Pi, and SPI speed runs as fast as 32MHz to support games and videos.

Now we have this 5-inch TFT display with a touch screen that can provide a high-resolution picture and a large viewing screen for your Raspberry Pi. The display supports any revision of Raspberry Pi and works perfectly for Raspberry Pi B+/ 2B/ 3B. It is the low power consumption for the backlight of the screen. The high 800 x 480 resolution can give you a full-color experience, the touch screen allows users to play easily.

The HY050CTP-HD 5 inch LCD Module is designed to work with HAOYU Electronics"s ARM development boards and MarsBoard"s single board computers. It has one 5 inch TFT LCD including capacitive touch screen with 800 by 480 pixels resolution.

The Capacitive touch panel is activated with anything containing an inductive load such as a finger or stylus. It allows for multi-touch options. When using the capacitive touch screen, the display needs a separate controller to interface with the touch panel. The display for capacitive touch is brighter since the touch panel is transparent.

The Transmissive polarizer is best used for displays that run with the backlight on all the time. This polarizer provides the brightest backlight possible. If you have a need for a bright backlight with lower power drain, transmissive is a good choice for this TFT LCD display.

Focus LCDs can provide many accessories to go with your display. If you would like to source a connector, cable, test jig or other accessory preassembled to your LCD (or just included in the package), our team will make sure you get the items you need.Get in touch with a team member today to accessorize your display!

Focus Display Solutions (aka: Focus LCDs) offers the original purchaser who has purchased a product from the FocusLCDs.com a limited warranty that the product (including accessories in the product"s package) will be free from defects in material or workmanship.