itead studio 3.2 tft lcd touch shield for arduino quotation

ITDB02-3.2S V2 display module is a 3.2" TFT LCD with 65K color 320 x 240 resolutions for Arduino microcontroller. The controller of this LCD module is ILI9341. It supports 16bit data interface with control interfaceof four wires. Moreover, this Arduino LCD module contains the touch screen and SD card socket as well.

itead studio 3.2 tft lcd touch shield for arduino quotation

And go to SONOFF official site for the latest SONOFF products info: https://sonoff.tech/,If you want to buy products on ITEAD STUDIO, please go to: https://itead.cc/

itead studio 3.2 tft lcd touch shield for arduino quotation

Arduino 3.2" TFT LCD Touch shield V1 is an Arduino Mega compatible, multicolored TFT display with touch-screen and SD card socket. It is available in an Arduino MEGA shield compatible pinout for attachment. The TFT driver is based on SSD1289 with 8bit data and 4bit control interface.

itead studio 3.2 tft lcd touch shield for arduino quotation

Sir I wasn"t referring to you. I was referring to the person who made the 8 Bit comment re: Arduino and his obvious lack of knowledge about Arduino and it"s capabilities. There were two links on the original post, the second link at the bottom of that page takes you to The "lesser" of the two displays was described in the original post as Only having an 8 Bit data bus and thus 256 colors... sounded to me as if though a person from Itead Studios was trying to "push" the more expensive of the two Itead products and that generated the energy to re read and confirm prior knowledge about parallel loading color graphic displays and that product specifically as I own one, bought it for $20.00 US

I am not aware of the data bus limiting color abilities. I am aware that the processor (Uno 328) can do int calculations and that the unsigned int declaration is for a 16 bit number. The loading of a 16 Bit number requires some small work to break it into bytes that the controller can use in 8 bit mode however I am not aware of any limitations that are created by using 8 bit mode except the time it take to load a graphic screen. So perhaps in my ignorance my post was inaccurate for this I apologize and should I be guilty of ignorance I will cheerfully remove the "inaccurate post" and apologize for misleading anyone that had the misfortune to read it.

itead studio 3.2 tft lcd touch shield for arduino quotation

Arduino 3.2" TFT LCD Touch shield V2 is an Arduino Mega compatible, multicolored TFT display with touch-screen and SD card socket as well. It is available in an Arduino MEGA shield compatible pinout for attachment. The TFT driver is based on ILI9341 with 8bit data and 4bit control interface.

itead studio 3.2 tft lcd touch shield for arduino quotation

ITEAD 3.2" TFT LCD Touch Shield is an Arduino Mega compatible multicolored TFT display with touch-screen and SD card socket. It is available in an Arduino MEGA Shield compatible pinout for attachment. The TFT driver is based on SSD1289 with 8bit data and 4bit control interface.

itead studio 3.2 tft lcd touch shield for arduino quotation

ER-TFTM032-3 is 240x320 dots 3.2" color tft lcd module display with ILI9341 controller board,superior display quality,super wide viewing angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO,ARM and Raspberry PI.It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.

It supports 8080 8-bit /9-bit/16-bit /18-bit parallel ,3-wire,4-wire serial spi interface.Built-in optional microSD card .It"s optional 3.2 " 4-wire resistive touch panel with controller XPT2046 and 3.2 " capacitive touch panel with controller FT6236 . It"s optional for font chip, flash chip and microsd card. We offer two types connection,one is pin header and the another is ZIF connector with flat cable mounting on board by default and suggested. Lanscape mode is also available.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!".Here is the link for 3.2"TFT Touch Shield with Libraries, EXxamples.Schematic Diagram for Arduino Due,Mega 2560 and Uno . For 8051 microcontroller user,we prepared the detailed tutorial such as interfacing, demo code and development kit at the bottom of this page.

itead studio 3.2 tft lcd touch shield for arduino quotation

Hi, I have womart 3.2TFT and I was trying with Arduino Mega and facing same problem of blank white screen (there is no flickering etc just white blank screen).

I can not suspect the TFT because I got this tested when I bought it in Shenzhen market (yes, I bought this when I visited China but could not get any other information form the shop owner - Need to know Chinese!!).

itead studio 3.2 tft lcd touch shield for arduino quotation

I havent been able to find much for others with the similar problem with this setup. That along with >2000 of these screens being sold by the vendor makes me think I may have a non functioning unit.