3.5inch raspberry pi lcd module 320x480 in stock

3.5inch RPi LCD (A) and 3.5inch RPi LCD (B) are hardware compatible with each other (uses different driver), and can be mutually substituted in most cases. (A) for low cost ver. while (B) for IPS ver. with better displaying.

Why the LCD doesn"t work with my Raspbian?To use the LCD with the Raspberry Pi official image, driver (SPI touch interface only) should be installed first. Please refer to the user manual.

However, for the first testing, you may want to use our image directly (if provided).Why the LCD still doesn"t work with the Waveshare provided image?Make sure the hardware connection is correct and connects fine.

The PWR will keep on and the ACT will keep blinking when the Raspberry Pi starts up successfully, in case both of the two LEDs keep on, it is possible that the image was burnt incorrectly OR the TF card was in bad contact.Which power supply should I use?It is recommended to use a 5V/3A power adapter for the Raspberry Pi other than USB connection, otherwise the Pi may failed to start up because the PC"s USB port might have not enough power.

Since the first-generation Raspberry Pi released, Waveshare has been working on designing, developing, and producing various fantastic touch LCDs for the Pi. Unfortunately, there are quite a few pirated/knock-off products in the market. They"re usually some poor copies of our early hardware revisions, and comes with none support service.

PO Box, APO/FPO, Afghanistan, Africa, Alaska/Hawaii, American Samoa, Armenia, Azerbaijan Republic, Bahrain, Bangladesh, Belarus, Bermuda, Bhutan, Brunei Darussalam, Cambodia, Central America and Caribbean, China, Cook Islands, Fiji, France, French Polynesia, Georgia, Germany, Greenland, Guam, Hong Kong, India, Indonesia, Iraq, Jordan, Kazakhstan, Kiribati, Kuwait, Kyrgyzstan, Laos, Lebanon, Macau, Malaysia, Maldives, Marshall Islands, Mexico, Micronesia, Mongolia, Nauru, Nepal, New Caledonia, Niue, Oman, Pakistan, Palau, Papua New Guinea, Philippines, Qatar, Russian Federation, Saint Pierre and Miquelon, Saudi Arabia, Solomon Islands, South America, Sri Lanka, Taiwan, Tajikistan, Tonga, Turkey, Turkmenistan, Tuvalu, US Protectorates, Ukraine, United Arab Emirates, Uzbekistan, Vanuatu, Vatican City State, Vietnam, Wallis and Futuna, Western Samoa, Yemen

PO Box, APO/FPO, Afghanistan, Alaska/Hawaii, Algeria, American Samoa, Angola, Armenia, Azerbaijan Republic, Bahrain, Bangladesh, Benin, Bermuda, Bhutan, Botswana, Burkina Faso, Burundi, Cambodia, Cameroon, Cape Verde Islands, Central African Republic, Chad, China, Comoros, Congo, Democratic Republic of the, Congo, Republic of the, Cook Islands, Côte d"Ivoire (Ivory Coast), Djibouti, Equatorial Guinea, Eritrea, Ethiopia, Falkland Islands (Islas Malvinas), Fiji, French Guiana, French Polynesia, Gabon Republic, Gambia, Georgia, Ghana, Guam, Guernsey, Guinea, Guinea-Bissau, Guyana, Hong Kong, Iraq, Jersey, Jordan, Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Lebanon, Lesotho, Liberia, Libya, Macau, Madagascar, Malawi, Maldives, Mali, Marshall Islands, Mauritania, Mauritius, Mayotte, Micronesia, Mongolia, Morocco, Mozambique, Namibia, Nauru, Nepal, New Caledonia, Niger, Niue, Oman, Pakistan, Palau, Papua New Guinea, Qatar, Reunion, Russian Federation, Rwanda, Saint Helena, Saint Pierre and Miquelon, Saudi Arabia, Senegal, Seychelles, Sierra Leone, Solomon Islands, Somalia, Sri Lanka, Suriname, Swaziland, Tajikistan, Tanzania, Togo, Tonga, Tunisia, Turkmenistan, Tuvalu, US Protectorates, Uganda, Ukraine, United Arab Emirates, Uzbekistan, Vanuatu, Vietnam, Wallis and Futuna, Western Sahara, Western Samoa, Yemen, Zambia, Zimbabwe

Combined with the Raspberry Pi, allows you to:Take photos by touching (up to 17 camera modes) Use software keyboard (system interaction without keyboard/mouse)

3.5inch RPi LCD (A) and 3.5inch RPi LCD (B) are hardware compatible with each other (uses different driver), and can be mutually substituted in most cases. (A) for low cost ver. while (B) for IPS ver. with better displaying.

To use the LCD with the Raspberry Pi official image, driver (SPI touch interface only) should be installed first. Please refer to the user manual. However, for the first testing, you may want to use our image directly (if provided).

Make sure the hardware connection is correct and connects fine. Make sure the image in TF card is burnt correctly. The PWR will keep on and the ACT will keep blinking when the Raspberry Pi starts up successfully, in case both of the two LEDs keep on, it is possible that the image was burnt incorrectly OR the TF card was in bad contact.

It is recommended to use a 5V/3A power adapter for the Raspberry Pi other than USB connection, otherwise the Pi may failed to start up because the PC"s USB port might have not enough power. For large size LCDs, say, 10inch diagonal or more, another stand-alone power adapter is also required to provide power to the LCD.

A Raspberry Pi is a palm size computer. It is handy for prototyping purposes with high computational power. Mostly, it is being used for IOT hardware applications.

The Pi has a HDMI output for direct monitor connection. But projects where space is a constrain, we need a small and compact display. This is where the popular 3.5 inch touch screen TFT LCD comes into play.

It is the cutest display for the Raspberry Pi. It features a 3.5" display with 480x320 16-bit color pixels and a resistive touch overlay. It"s designed to fit nicely not only to the Pi Model A or B but also works perfectly fine with the Model B+/2B/3B/4B.

*When working with Raspberry Pi 4, for the system image of Raspberry Pi after 2021-10-30, for example on Bullseye, please modify "dtoverlay = vc4-kms-v3d" to "dtoverlay = vc4-fkms-v3d" in the config file, otherwise it may fail to start. But on Buster, please comment out "dtoverlay = vc4-fkms-V3D" by adding #.

· The case can be used as raspberry pi case with mini cooling fan and 3.5 inch screen installed. The ABS case is specially designed for Raspberry Pi 4 Model B only.

· The LCD touch screen can use GPIO interface for power supply; The LCD screen has a 2-pin interafce for connecting the cooling fan, which can allow the screen and cooling fan both working at the same time.

· The LCD touch screen is suitable for Raspberry Pi 4B/ 3B/ 3B+ versions. When used for Pi 4B, it can support for Raspbian system, for kali Linux system. When used for 3B/3B+, it can support for Raspbian system, for ubuntu system ,for kali Linux system.

· The case features an easy-to-install split design that protects your PI computer and screen, as well as a cooling fan mounted on an aluminum stand and a hot silicon pad for cooling the chip to keep the PI computer and screen cool.