sainsmart tft lcd shield price

This is SainSmart MEGA2560  + 7 inch TFT LCD module with the TFT LCD shield kit For arduino enthusiasts.It includes one pcs of SainSmart MEGA2560 , 7 inch TFT LCD display and a TFT LCD shield for Arduino MEGA2560.This kit helps you to avoid complicated wiring processes and save you much time to accomplish your goal. You can feel free to enjoy the touch function and SD card function by using our codes.We will provided you the whole document including the example project of the kit. We will supply you the technical support after your purchase.

The MEGA2560 R3 also adds SDA and SCL pins next to the AREF. In addition, there are two new pins placed near the RESET pin. One is the IOREF that allow the shields to adapt to the voltage provided from the board. The other is a not connected and is reserved for future purposes. The MEGA2560 R3 works with all existing shields but can adapt to new shields which use these additional pins.

It is 100% compatible with the normal MCU like ARM AVR PIC and 8051,especially on Arduino family such as Arduino Due and Arduino MEGA2560(R3). The module uses the LCD controller Chip SSD1963 with 7 inch LCD including the touchscreen.

LCD-specificed intialization code is provided, so that you can save time to optimize power control register and gamma curves for best display performance. We have test the provided code, it gives the best display performanace

This is Sainsmart TFT LCD Extend shield for arduino due .Using this shield can help you out of the bothers to use other cables. You just need to plug the module to arduino due through this shield.

The shield defines that all the the data transmit ports are PC1-PC8 and PC12-PC19,the controll pins are PD0-PD3.The perfect design could realize that the data transmits in high speed.The SPI interface is designed in the ISP header of arduino due so that the SPI transfer with DMA could be achieved in high speed with no drag.

This shiled is just for Arduno MEGA2560. If you need the LCD Extend shield for Arduino Due,you need a similar shield which is also provided from our store.

This shiled is just for 7 inch TFT LCD.If you need the LCD Extend shield for 3.2/3.5/...,you need a similar shield which is also provided from our store.

The SainSmart TFT LCD module works in 3.3V voltage level and you need to use cables to connect with Arduino Mega. And this shield can help you out of the bothers to use other cables. You just need to plug the module to Mega through this shield.

This is SainSmart 5 inch TFT LCD module with the TFT LCD shield kit for arduino enthusiasts.It includes one piece of 5 inch TFT LCD display and a TFT LCD shield for arduino due.We will provided you the whole document including the example project of arduino due with the kit. We will supply you the technical support after your purchase.

The SainSmart Due is a microcontroller board based on the Atmel SAM3X8E ARM Cortex-M3 CPU (Datasheet). It is the first Arduino board based on a 32-bit ARM core microcontroller. It has 54 digital input/output pins (of which 12 can be used as PWM outputs), 12 analog inputs, 4 UARTs (hardware serial ports), a 84 MHz clock, an USB OTG capable connection, 2 DAC (digital to analog), 2 TWI, a power jack, an SPI header, a JTAG header, a reset button and an erase button.

LCD-specified initialization code is provided, so that you can save time to optimize power control register and gamma curves for best display performance. We have test the provided code, it gives the best display performanace

It is 100% compatible with the normal MCU like ARM AVR PIC and 8051,especially on arduino family such as arduino due and arduino mega2560(R3).The module uses the LCD controller Chip SSD1963 with 5 inch LCD including the touchscreen.

The shield defines that all the the data transmit ports are PC1-PC8 and PC12-PC19,the controll pins are PD0-PD3.The perfect design could realize that the data transmits in high speed.The SPI interface is designed in the ISP header of arduino due so that the SPI transfer with DMA could be achieved in high speed with no drag.

This is Sainsmart Due + 7 inch TFT LCD module with the TFT LCD shield kit For arduino enthusiasts.This kit helps you to avoid complicated wiring processes and save you much time to accomplish your goal.

The SainSmart Due is a microcontroller board based on the Atmel SAM3X8E ARM Cortex-M3 CPU .It is the first Arduino board based on a 32-bit ARM core microcontroller. It has 54 digital input/output pins (of which 12 can be used as PWM outputs), 12 analog inputs, 4 UARTs (hardware serial ports), a 84 MHz clock, an USB OTG capable connection, 2 DAC (digital to analog), 2 TWI, a power jack, an SPI header, a JTAG header, a reset button and an erase button.

The shield defines that all the the data transmit ports are PC1-PC8 and PC12-PC19,the controll pins are PD0-PD3.The perfect design could realize that the data transmits in high speed.The SPI interface is designed in the ISP header of arduino due so that the SPI transfer with DMA could be achieved in high speed with no drag.

Reason: The hooks on the backight of ER-TFT032-3.1 is always complained by most customers for inconvenient assembly. So we cancel the hooks in the new version of ER-TFT032-3.2.That"s the only difference for these two versions.

ER-TFT032-3.2 is 240x320 dots 3.2" color tft lcd module display with ILI9341 controller and optional 4-wire resistive touch panel and 3.2 inch capactive touch panel with controller FT6236,superior display quality,super wide viewing angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO ARM and Raspberry PI.It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.It supports 8080 8/16-bit parallel,3/4-wire serial interface. FPC with zif connector is easily to assemble or remove.Lanscape mode is also available.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!".Here is the link for 3.2"TFT Touch Shield with Libraries, Examples.Schematic Diagram for Arduino Due,Mega 2560 and Uno . For 8051 microcontroller user,we prepared the detailed tutorial such as interfacing, demo code and development kit at the bottom of this page.

In this Arduino touch screen tutorial we will learn how to use TFT LCD Touch Screen with Arduino. You can watch the following video or read the written tutorial below.

As an example I am using a 3.2” TFT Touch Screen in a combination with a TFT LCD Arduino Mega Shield. We need a shield because the TFT Touch screen works at 3.3V and the Arduino Mega outputs are 5 V. For the first example I have the HC-SR04 ultrasonic sensor, then for the second example an RGB LED with three resistors and a push button for the game example. Also I had to make a custom made pin header like this, by soldering pin headers and bend on of them so I could insert them in between the Arduino Board and the TFT Shield.

Here’s the circuit schematic. We will use the GND pin, the digital pins from 8 to 13, as well as the pin number 14. As the 5V pins are already used by the TFT Screen I will use the pin number 13 as VCC, by setting it right away high in the setup section of code.

I will use the UTFT and URTouch libraries made by Henning Karlsen. Here I would like to say thanks to him for the incredible work he has done. The libraries enable really easy use of the TFT Screens, and they work with many different TFT screens sizes, shields and controllers. You can download these libraries from his website, RinkyDinkElectronics.com and also find a lot of demo examples and detailed documentation of how to use them.

After we include the libraries we need to create UTFT and URTouch objects. The parameters of these objects depends on the model of the TFT Screen and Shield and these details can be also found in the documentation of the libraries.

So now I will explain how we can make the home screen of the program. With the setBackColor() function we need to set the background color of the text, black one in our case. Then we need to set the color to white, set the big font and using the print() function, we will print the string “Arduino TFT Tutorial” at the center of the screen and 10 pixels  down the Y – Axis of the screen. Next we will set the color to red and draw the red line below the text. After that we need to set the color back to white, and print the two other strings, “by HowToMechatronics.com” using the small font and “Select Example” using the big font.

SainSmart 3.2" TFT LCD Display + TFT LCD Shield For Arduino Mega2560 R3. Overview: SainSmart 3.2" TFT LCD Display is a LCD touch screen module. It has 40pins interface and SD card and Flash reader design. It is a powerful and multifunctional module for your project. The Screen include a controller SSD1289, it"s a support 8/16bit data interface , easy to drive by many MCU like STM32 ,AVR and 8051. It is designed with a touch controller in it . The touch IC is ADS7843 , and touch interface is included in the 40 pins breakout. It is the version of product only with touch screen and touch controller. Specification: 240374PQ 65K color 320*240 3.2 inch Wide viewing angle SSD1289:240 RGB x 320 TFT Driver Integrated Power, Gate and Source Driver With RAM ADS7843:4-WIRE TOUCH, UP TO 125kHz CONVERSION RATE, SERIAL INTERFACE SainSmart 3.2 TFT LCD shield works in 3.3V voltage level and you need to use cables to connect with Arduino Mega. And this shield can help you out of the bothers to use other cables. You just need to plug the module to Mega through this shield.This shield supports both 16 bit mode. And Mega board has enough pins for using SD card and touch function at the same time.It also has an adjustable button for contrast of the LCD display. Packing List: 1 X SainSmart 3.2 inch TFT LCD 1 X Shield Board for Arduino Mega2560 R3 Item will be shipped within 1-2 working days after full payment is cleared. Tracking number will be sent to all customers upon package shipment. Delivery time is different in accordance to shipping address and shipping methods. -Economy shipping from China: about 20-30 business days. -ePacket delivery (EUB) from China to US: about 10-15 business days. -Expedited shipping from China takes about 3-5 business days via DHL/UPS and 9-15 business days via EMS. -Standard shipping (Royal Mail Tracked) from UK warehouse to local customers: about 3-5 business days. -Standard shipping from US warehouse: about 3-7 business days. -Expedited shipping from US warehouse: about 3-5 business days. Delivery time depends on destination logistics mode and other factors. If you have not received your shipment within 30 days from payment, please feel free to contact us. We will track the shipment and get back to you as soon as possible with a reply. We accept payment via PAYPAL ONLY . We only ship to confirmed PAYPAL addresses. Please make sure payment address in PayPal is correct. All major credit cards are accepted through our secure payment processor PayPal. Payment must be received within 7 business days of auction closing. 60 days money back return policy . If you are not satisfied when you receive your item, please return it within 60 days for a replacement or money back. Please contact us for return address before you send it back. If item defective, In 3 months we will send you a replacement without extra charge, or offer refund upon faulty received. After 3 months you are still welcomed to send it back to us for exchange. Buyer may responsible for all return shipping costs. In case you receive wrong products due to shipping error, please contact us for exchange or refund. If it"s damaged, please refuse to accept and contact us as soon as possible. Please email us before leaving any negative feedback or open any dispute on PayPal. We care about our valued customers, and will always try to help you. So if you have any problems, please e-mail us immediately. We try our best to reply to your emails as soon as possible. If you do not receive any reply from us, please check your email ensuring your mailbox has not reached full size. You can contact us by Ebay messages are strongly recommended. On Oct-25-17 at 03:43:18 PDT, seller added the following information:

LCD Display Modules└ LEDs, LCDs & Display Modules└ Electronic Components & Semiconductors└ Electrical Equipment & Supplies└ Business & IndustrialAll CategoriesAntiquesArtBabyBooks & MagazinesBusiness & IndustrialCameras & PhotoCell Phones & AccessoriesClothing, Shoes & AccessoriesCoins & Paper MoneyCollectiblesComputers/Tablets & NetworkingConsumer ElectronicsCraftsDolls & BearsMovies & TVEntertainment MemorabiliaGift Cards & CouponsHealth & BeautyHome & GardenJewelry & WatchesMusicMusical Instruments & GearPet SuppliesPottery & GlassReal EstateSpecialty ServicesSporting GoodsSports Mem, Cards & Fan ShopStampsTickets & ExperiencesToys & HobbiesTravelVideo Games & ConsolesEverything Else

2012 latest IIC LCD2004-character LCD display module, a new high-quality 4 line 20 character LCD module not only set the contrast control knob selector switch also has a backlight and IIC communication interface. For Arduino beginners, not for the cumbersome and complex LCD driver circuit connection and a headache, the real significance of this LCD module will simplify the circuit, this module directly into the Arduino Sensor Shield V5.0 sensor expansion board IIC device interface can, GM 4P sensor connection cable, programmed through the Arduino controller, you can easily identify the slogan, sensor data records.

This is TFT LCD Extend shield for Arduino MEGA2560(R3). Using this shield can help you out of the bothers to use other cables. You just need to plug the module to Arduino MEGA2560(R3)  through this shield.

The shield defines that all the the data transmit ports are PC1-PC8 and PC12-PC19,the controll pins are PD0-PD3.The perfect design could realize that the data transmits in high speed.The SPI interface is designed in the ISP header of arduino due so that the SPI transfer with DMA could be achieved in high speed with no drag.

The SainSmart 3.2 TFT LCD module works in 3.3V voltage level and you need to use cables to connect with Arduino Mega. And this shield can help you out of the bothers to use other cables. You just need to plug the module to Mega through this shield. This shield supports both 16 bit mode. And Mega board has enough pins for using SD card and touch function at the same time. It also has an adjustable button for contrast of the LCD display. Manual?https://s3-ap-northeast-1.amazonaws.com/sain-amzn/20/20-011-919/CTE_MEGA_shield.zip ?

If you are looking to get into Arduino development or are wanting to expand your existing collection, this is the perfect item for you. You get a great value for your money:SainSmart Mega 2560 board (Arduino clone) ($33)SainSmart TFTP display with touch screen and full sized SD card slot ($25)SainSmart TFTP Display adaptor ($15)Short USB cableI spent $46 for this setup, so the value is obvious.The Mega 2560 clone worked perfectly, the display worked perfectly and the adapter board mated them properly. I had purchased a Seeed 3.2" display at Radio Shack for $49. It had many issues and I returned it and used the money to buy this setup. This display is much faster than the Seeed display and the drivers were very easy to locate and install. Just google "UTFT drivers henningkarlsen" and get all of the UTFT drivers. Henning has several more drivers on his site, go ahead and get them all. They are very easy to use and configure. To use the drivers with this particular board (they are "universal drivers") use this setting for the board type:UTFT myGLCD(ITDB32S,38,39,40,41); // the ITB32s and correct pins for Mega shieldSo in summary:Pros:1. Great value for the money2. Everything worked greatCons:1. Not a "real" Arduino. You"ll have to decide for yourself how important this is to you.The nice thing about SainSmart is that they admit that they are cloning the Arduino boards. Most of the boards available on Amazon are counterfeits and the sellers are not particularly upfront about this. These counterfeit boards exactly copy the Arduino boards, definitely graying the area between legitimacy and piracy. SainSmart clearly marks their boards as clones. I appreciate this honesty in a company, especially when there"s more money to be made by tricking buyers into purchasing counterfeit boards.I highly recommend this package for anyone wanting to get into Arduino development or wanting a touchscreen. The value is great. Now, I guess I need to hunt down a 7" TFTP display to continue this adventure.[9/19/13] Update:After digging into the touch screen, I found that the UTouch lib had some serious accuracy problems, even after trying to use the calibration utility provided with the library. I re-wrote the lib and now I find that the accuracy of the screen is very good. To re-write the lib, you need to take these factors into account:1. The reading of the x values for the screen at the extreme left and right edges.2. The reading of the y values for the screen at the extreme top and bottom edges.This is confused a bit by the fact that the screen is natively in portrait mode. Which is to say that the long side is the y-axis and the short-side is the x-axis. I wanted a landscape mode, so I swapped the coordinates in my driver.Once you know the x and y extremes for the touch screen, simply use the map function to map them to the actual screen coordinates. This gives you a pretty accurate x and y for the display.The other issue I had was with how the touch screen was sampled. The library code polls the touch screen several times per read and averages the results to get a more accurate reading. In the case of "EXTREME" accuracy, it polls 10 times. The problem with this is that if you lift your stylus during the polling, the last few reads are bogus and throw the entire read off. You can see this happening in the SainSmart demo video that they posted for this device. The symptoms are that pixels get set on the sample paint program way far away from where the stylus is. Not cool! The fix is to only sample the screen if the screen is detecting the stylus as being pressed. You can do this by checking the dataAvailable() before each read in the poll. If there is no data available, don"t do the read.I wish I had a more effective method of sharing this information with the Arduino community.

Arduino mega + 3.2" tft case. there are 2 different case bottoms, 1 without a hole and 1 with. both cases have a cutout for powering the Mega from a USB.

I designed this to dress up a project that used the SainSmart LCD Keypad Shield with and Arduino. The bezel itself prints pretty easily with very little support structure needed. The buttons are designed to be self-captivating (they just push in and...

I didn"t have a 3.5" TFT screen, but I did have the 3.2" ones (at the time the 3.5" were on backorder and I got impatient). This fits my 3.2" TFT perfectly. ... My unit comes from 4D Systems as well.

This top surface has 4 additional holes (for screwing to the bezel) and a square cut out of it to fit the LCD circuit board (see attached photo above) The bezel has 4 screw holes that line up with laser cut holes in the laser cut back plate. the...

Support piece for SainSmart kit: http://www.sainsmart.com/sainsmart-mega2560-board-3-5-tft-lcd-module-display-shield-kit-for-atmel-atmega-avr-16au-atmega8u2.html When both the shields are stacked, they are kind of flappy. This part fits on one end...

accurate CAD model of UPC "6013801500024" from the SainSmart Raspberry Pi 3 Model B Ultimate Kit with 5 inch LCD (Red&White Case)https://smile.amazon.com/gp/product/B01FHEBIE0/

A (very) compatible 800x480 LCD is available, but it"s 5 inch big and so the original bezel won"t fit. I also didn"t like the idea of sticking LCD to PCB by a piece of double sided tape. Here"s my original post about hacking it in:(pocket)CHIP with...

I bought a 4.3" TFT LCD Color Monitor off eBay for a reverse camera I installed in my car and had nothing to mount it to my car with. Monitor dimensions were 120mm(L) x 75mm(W) x 15mm(H) and this seemed to fit quite snugly. I have only created a...

This is a sipmple box/case for Arduino Uno and 2.4"" TFT Lcd Touch Screen. There are 2 kind of cases: closed or with open grooves for refrigeration. Originally made for a mini - meteo station, it can be customizable with FreeCad file. ...It was made...

A small mountable holder for a fasttech LCD module. Mounting pins are a little tight but can be snapped off if not needed. Mount holes are designed for assorted leg or spacer designs. Holes are 5mm dia, 34mm apart and hole centre 5.5mm from edge if...

I just redesigned it so it can house cheap chinese 2.4" TFT touchscreen, instead of hard to find and expensive 2.8". No support is needed for any of parts.

This is an update to the FreeTouchDeck case by Dustin Watts that holds a 3.2" TFT display since I bought a different size than Dustin used. I modified the Top_for_TFT_with_Headers.stl file. I"ve also uploaded the Fusion 360 file....

Step 1: Remove dial knob by grabbing the whole knob and pulling towards yourself Step 2: Remove 2ea 3mm front mount screws Step 3: Remove 4ea 2mm from the backside of the LCD screen that mount the circuit board to the frame bracket Step 4: Snap your...

Step 1: Remove dial knob by grabbing the whole knob and pulling towards yourself Step 2: Remove 2ea 3mm front mount screws Step 3: Remove 4ea 2mm from the backside of the LCD screen that mount the circuit board to the frame bracket Step 4: Snap your...

LCD screen bezel for Oneplus 2. If not only your screen is destroyed, but also the black plastic frame surrounding it (see picture), you can try your luck by printing this bezel and installing it. Replacement screens do not come with this bezel,...

3.2"inch TFT LCD Module Display Power than SainSmart w/Resistive Touch,Tutorial. 3.2"TFT LCD Display with Breakout Board andwith Resistive Touch Panel. 3.2"TFT LCD Display with Breakout Boardand with Capacitive Touch Panel. I t supports 8080 8-bit /9-bit/16-bit /18-bit parallel ,3-wire,4-wire serial spi interface.Built-in optional microSD card slot, optional. Description E R-TFTM032-3 is 240x320 dots 3.2" color tft lcd module display with ILI9341 controller board,superior display quality,super wide viewing angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO,ARM and Raspberry PI.It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image. I t supports 8080 8-bit /9-bit/16-bit /18-bit parallel ,3-wire,4-wire serial spi interface.Built-in optional microSD card slot, optional 3.2 inch 4-wire resistive touch panel with controller XPT2046 an d 3.2 inch capacitive touch panel with controller FT6236 . It"s optional for font chip, flash chip and microsd card. W e offer two types connection,one is pin header and the another is ZIF connector with flat cable mounting on board by default and suggested. Lanscape mode is also available. O f course, we wouldn"t just leave you with a datasheet and a "good luck!".Here is the link for 3.2"TFT Touch Shield with Libraries, EXxamples.Schematic Diagram for Arduino Due,Mega 2560 and Uno . For 8051 microcontroller user,we prepared the detailed tutorial such as interfacing, demo code and Development Kit at the bottom of this page.3D drawing is available. 3.2 inch Series TFT Display L ist ↓ Display Part Number Description ER-TFT032-2(RTP) 3.2" TFT LCD 240x320 Pixels Display with Controller ic ILI9320 and Resistive Touch Panel ER-TFT032-3.1(RTP) 3.2" TFT LCD 240x320 Pixels Display with Controller ic ILI9341 and Resistive Touch Panel ER-TFT032-3.1(CTP) 3.2" TFT LCD 240x320 Pixels Display with Controller ic ILI9341 and Capacitive Touch Panel ER-TFT032A3-3(RTP) 3.2" TFT LCD 240x320 Pixels Display with Controller ic ST7789V and Resistive Touch Panel ER-TFT032A3-3(CTP) 3.2" TFT LCD 240x320 Pixels Display with Controller ic ST7789V and Capacitive Touch Panel ER-TFTM032-3(RTP) 3.2"TFT LCD Display with Breakout Board and with Resistive Touch Panel ER-TFTM032-3CTP) 3.2"TFT LCD Display with Breakout Board and with Capacitive Touch Panel W hat"s inc luded in the package ↓ Num Accessory Name Qty 1 3.2 inch TFT Display with Breakout Board 1 2 3.2" Resistive Touch Panel with controller XPT2046 1 * The touch panel is attached on the display by default. * We default pin header connection , 5V power supply and 4-wire serial interface .Please send message if you want FFC connection , 3.3V power supply and other interface , or buy from our own store [link removed by eBay] . O ptional Accessory List (Click the part number to buy accessories) ↓ Category Part Number Description Flash Chip W25Q128FVSG WINBOND (P/N:25Q128FVSG) 128M Bit Flash Chip MicroSD Card ER3297 New Original MicroSD (TF) 1GB Memory Card Font 1 ER3300-1 15X16 dots fonts chip,it supports Chinese,Japanese(compatible with Unicode) and 150 countries character Font 2 ER3301-1 11X12,15X16 dots fonts chip, it supports Chinese,ASCII and 150 countries character Font 3 ER3303-1 11X12 , 15X16 , 24X24 dots Chinese font, It supports GB2312,GB12345 and ASCII character, also compatible with Unicode Font 4 ER3304-1 12x12,16x16,24x24,32x32 dot matrix Chinese font, supporting GB2312 Simplified Chinese and ASCII * If choose the above accessories,we"ll mount on display by default except the flash chip. Ebay doesn"t allow listings to contain external links,so the documents link may be invalid. Please copy the below entire link to your browser for checking our documents(at the bottom of the page) or for bulk order. https://www.buydisplay.com/default/3-2-inch-capacitive-touchscreen-240x320-tft-lcd-module-display D atasheet - TFT LCD Display,Controller,Connector ↓ Format Documents Name (Downloadable) Version Language Update Date Size 3.2 inch 240x320 Dots Display with Adaptor Board Datasheet 2.0 English Jan-09-2016 709K Controller ILI9341 Datasheet 1.0 English Jul-02-2013 3.2M 40 Pins 1.00mm Pitch ZIF Connector Drawing 1.0 English Apr-19-2013 268K Datasheet - Touch Panel with its Controller IC,Connector ↓ Format Documents Name (Downloadable) Version Language Update Date Size 3.2 inch 4-Wire Resistive Touch Panel Drawing 1.0 English Jun-06-2016 302K Resistive Touch Panel Controller XPT2046 Datasheet 1.0 English May-08-2007 579K 3.2 inch Capacitive Touch Panel Outline Drawing 1.0 English Dec-02-2015 254K Capacitive Touch Panel Controller FT6236 Datasheet 1.0 English Jul-24-2014 674K Datasheet for Flash Memory,MicroSD Card Slot ↓ Format Documents Name (Downloadable) Version Language Update Date Size 128M-BIT Flash W25Q128FV Datasheet 1.0 English Oct-01-2012 1.0M MicoSD Card Slot Drawing 1.0 English Dec-12-2013 1.2M Datasheet for Font Chip ↓ Format Documents Name (Downloadable) Version Language Update Date Size Summary for Font Chip 1.0 English Aug-07-2013 133K ER3300-1 Datasheet 1.0 English May-08-2010 621K ER3301-1 Datasheet 1.0 English Mar-27-2014 2.0M ER3303-1 Datasheet 1.0 English Oct-01-2013 688K ER3304-1 Datasheet 1.0 English Apr-12-2013 935K T utorial - 8051 Microcontroller Demo Code,Interfacing,Development Board&Kit ↓ Format Documents Name (Downloadable) Version Language Update Date Size 3-Wire SPI,Touch Panel,Font Chip,Flash,MicroSD Demo Code 1.0 English Nov-28-2014 180K 4-Wire SPI,Touch Panel,Font Chip,Flash,MicroSD Demo Code 1.0 English Nov-28-2014 180K 8080 8-Bit,Touch Panel,Font Chip,Flash,MicroSD Demo Code 1.0 English Nov-28-2014 179K 8080 16-Bit,Touch Panel,Font Chip,Flash,MicroSD Demo Code 1.0 English Nov-28-2014 179K ER-TFTM032-3 Interfacing Document 1.0 English Aug-2014-23 176K 8051 Microcontroller Development Board & Kit for ER-TFTM032-3 N/A N/A N/A N/A Specification Gross Weight (kg)0.0760 ManufacturerEastRising Continuity SupplyWe promise the long term continuity supply for this product no less than 10 years since 2015. Part NumberER-TFTM032-3 Display Format240x320 Dots Interface8080 8-bit Parallel , 8080 16-bit Parallel , 3-Wire Serial SPI, 4-Wire Serial SPI IC or EquivalentILI9341 AppearanceRGB on Black Diagonal Size3.2” ConnectionPin Header, FFC-Connector Outline Dimension64.9W)x89.4(H)mm Visual Area48.60x64.80mm Active Area48.60(W)x64.80(H)mm Character SizeNo Dot (Pixel) SizeNo Dot (Pixel) Pitch0.2025x0.2025 IC PackageSMT Display TypeTFT-LCD Color Touch Panel OptionalYes Sunlight ReadableNo Response Time(Typ)25ms Contrast Ratio(Typ)500:1 Colors65K/262K Viewing Direction12:00 Viewing Angle RangeLeft:60.0 , Right:60.0 , Up:50.0 , Down:50.0 degree Brightness(Typ)280cd/m2 Backlight ColorWhite Color Backlight Current (Typ)120mA Power Supply(Typ)3.3V, 5V Supply Current for LCM(Max)130mA (Vdd=3.3V) 150mA (Vdd=5V) Operating Temperature-20℃~70℃ Storage Temperature-30℃~80℃ Series NumberER-TFT032-3 About Us We"re China-based global display manufacturer named EastRising Technology Co.,Ltd. that has a worldwide business in design, produce and sell various displays for small to large companies since 2003. Our web site is [link removed by eBay] . Link for video and image of our production line and equipment. RoHS reports for all material we used on display module. Long Term Continuity Supply Warranty We promise the long terms continuity supply and would never end.Some controller IC may stop the production,we"ll try our efforts to find the completely compatible ones.If the equivalent is unavailable, we¡¯ll make the new tooling and use the most similar IC as replacement.So you don"t have to worry even your research time is very long. Shipping Policy All products will be checked carefully and packed in good condition before shipping.We e-mail all customers with tracking information immediately after the shipment for status tracking. Item will be shipped within 1 business day after the payment has been received. Customs fees and import duties for exports are buyer"s responsibility. Warranty All products are covered under our limited warranty, which provides all products are free of functional defects for a period of one year from the date of receipt and all products are free of visual defects and missing parts for a period of 30 days from the date of receipt.If a product was damaged during shipping or the order is incorrect,you must notify us within 2 days of receipt. How to return a product First request an RMA number from our sales with the information:part number,reason for return,order number. Our sales will then either issue an RMA number, ask you for more information, or offer to help you resolve a technical problem so that the product does not need to be returned. Products must arrive here in the same condition as when you received them. You are responsible for return shipping and insurance.Please make sure your RMA number is on the shipping label and on any documents you include with the product. After we receive the product, we inspect it to determine the cause of any defect, then update by email with our findings. This process usually takes five business days.

The Sensor Shield V5.0 for Arduino is the latest shield compatible to Arduino UNO and Arduino Due. This Sensor Shield retains the advantages of version V4.0 on the basis of stack design, PCB Immersion Gold processing technology. Newly added many kinds of interface, for example, IIC interface, 32 channels servo motor interface, Bluetooth communication module interface, SD Card communication module interface and so on, more convenient.

Sensor Shield allows you to connect to various modules like sensors, servos, relays, buttons, potentiometers and many more directly to your Arduino through this Sensor Shield.

Each functional module has buckled port with VCC, GND, and Output, which has the corresponding port on the Sensor Shield, connected with a dual-female cable you may start playing already. Buckled brick cables are like cement for bricks, make the connections easier, secure and more professional looking.

Each functional module has buckled port with VCC, GND and Output, which has corresponding port on the Sensor Shield, connected with a plain 2.54mm dual-female cable you may start playing already. Buckled brick cables are like cement for bricks, make the connections easier, secure and more professional looking.