lcd module 4x10 in stock

EA DOGS104-A Issue 11.2020 4x10/2x10 incl. SSD1803A for SPI, IC Dimension 36,0 x 27.5 x 4.6 mm TECHNICAL DATA * HIGH-CONTRAST LCD SUPERTWIST DISPLAY * OPTIONAL LED BACKLIGHT UNITS IN DIFFERENT COLORS * 4x10 CHARACTER WITH 2.6 mm SWITCHABLE TO 2X10 WITH 4.55 mm HEIGHT * SSD1803A CONTROLLER FOR SPI (2-/3-/4-WIRE) AND IC (2-WIRE) INTERFACE * SINGLE POWER SUPPLY +3.3V (typically 440A) * NO ADDITIONAL VOLTAGES REQUIRED * OPERATING TEMPERATURE RANGE -20 THROUGH +70C * LED BACKLIGHT 3 ..45mA 3.3V * NO MOUNTING REQUIRED, SIMPLY SOLDER INTO PCB * 3 DIFFERENT CHARACTER SETS (CYRILLIC, ENGLISH-JAPANESE AND EUROPEAN) INCLUDED IN THE SAME CONTROLLER * 2 VIEWING DIRECTION POSSIBLE (BOTTOM AND TOP VIEW) ORDERING CODE LCD MODULE 4x10 - 2.6 mm EA DOGS104x-A x: B = blue background transmissive W = white background transfelctive N = white background reflective LED-BACKLIGHT AMBER EA LED36X28-A LED-BACKLIGHT YELLOW-GREEN / RED EA LED36X28-GR LED-BACKLIGHT GREEN/ RED/ WHITE EA LED36X28-ERW ACCESSORIES USB-TESTBOARD FOR PC (WINDOWS) EA 9780-4USB SOCKET CONNECTOR 4,8mm HOCH (2 PCS REQUIRED) EA FL-10P available at 1 piece Switchable font heightEA DOGS04-A EA DOG SERIES With its EA DOG series, ELECTRONIC ASSEMBLY presents the worlds first display series which will run on 3.3 V systems without auxiliary power. Unlike normal LCD modules, you order the display and the corresponding backlight separately. This gives you a wealth of possible combinations. Designed for compact hand-held devices, this modern LCD range provides a number of real benefits with or without backlight: * extremely compact at 36,0x27,5 mm at the standard font size of 2.6 mm (4 x 10) * ultra-flat at 2.0 mm without backlight or 4.6 mm including LED backlight * SPI interface (2-/3-/4-wire) and IC (2-wire) * typical power consumption of only 440A in full operation (LED white backlight as of 3mA) * easy installation by simply soldering into the board * A whole range of design variants can be supplied as of single units * Changing background color LED BACKLIGHTS 3 different variants are available for Limiting resistor individual backlighting: amber, yellow- amber Forward Current EA LED36x28-A voltage max. green/red, green/red/white. 3,3 V 5V For the amber backlight, 2 separate LED Connected in parallel 2,1 V 60 mA 20 ohm 48 ohm paths are available, which can be switched Connected in series 4,2 V 30 mA - 27 ohm in parallel or in series to ideally match the system voltage. This means that all the Limiting resistor backlights can be run either at 3.3 V and green/red/white Forward Current higher voltages. EA LED36X28-ERW voltage max. 3,3 V 5 V Operation of the backlight requires an green path 3,0V 45 mA 7 ohm 45 ohm external series resistor for current limiting. red path 2,1 V 45 mA 27 ohm 65 ohm This can be calculated by R=U/I you will white path 3,0 V 30 mA 10 ohm 67 ohm find the values in the table. To improve life time it is recommanded to use a current source only. Limiting resistor yellowgreen/red Forward Current EA LED36x28-GR voltage max. The operating life of the yellow/green, red 3,3 V 5V and amber backlights is 100,000 hours and red path (AGR/CR) 2,1 V 45 mA 27 ohm 65 ohm that of the white backlight is a bit shorter. yellowgreen path (AGR/CG) 2,1 V 60 mA 20 ohm 48 ohm Important: Never operate the backlight directly on a 5 V/3.3V supply, as this can immediately destroy the LEDs INSTALLATION First, the display and the corresponding backlight are clipped together. The complete unit is then inserted into a PCB and soldered. Note that the 4 pins for the backlight must also be soldered from the top with less tin. Important: There are one or two protective films on the display (top and/or rear side) and one on each backlight. Those have to be removed during or after production. Page 2 Printing and typographical errors reserved. ELECTRONIC ASSEMBLY reserves the right to change specifications without prior notice.

EA DOGS104-A Issue 11.2020 4x10/2x10 incl. SSD1803A for SPI, IC Dimension 36,0 x 27.5 x 4.6 mm TECHNICAL DATA * HIGH-CONTRAST LCD SUPERTWIST DISPLAY * OPTIONAL LED BACKLIGHT UNITS IN DIFFERENT COLORS * 4x10 CHARACTER WITH 2.6 mm SWITCHABLE TO 2X10 WITH 4.55 mm HEIGHT * SSD1803A CONTROLLER FOR SPI (2-/3-/4-WIRE) AND IC (2-WIRE) INTERFACE * SINGLE POWER SUPPLY +3.3V (typically 440A) * NO ADDITIONAL VOLTAGES REQUIRED * OPERATING TEMPERATURE RANGE -20 THROUGH +70C * LED BACKLIGHT 3 ..45mA 3.3V * NO MOUNTING REQUIRED, SIMPLY SOLDER INTO PCB * 3 DIFFERENT CHARACTER SETS (CYRILLIC, ENGLISH-JAPANESE AND EUROPEAN) INCLUDED IN THE SAME CONTROLLER * 2 VIEWING DIRECTION POSSIBLE (BOTTOM AND TOP VIEW) ORDERING CODE LCD MODULE 4x10 - 2.6 mm EA DOGS104x-A x: B = blue background transmissive W = white background transfelctive N = white background reflective LED-BACKLIGHT AMBER EA LED36X28-A LED-BACKLIGHT YELLOW-GREEN / RED EA LED36X28-GR LED-BACKLIGHT GREEN/ RED/ WHITE EA LED36X28-ERW ACCESSORIES USB-TESTBOARD FOR PC (WINDOWS) EA 9780-4USB SOCKET CONNECTOR 4,8mm HOCH (2 PCS REQUIRED) EA FL-10P available at 1 piece Switchable font heightEA DOGS04-A EA DOG SERIES With its EA DOG series, ELECTRONIC ASSEMBLY presents the worlds first display series which will run on 3.3 V systems without auxiliary power. Unlike normal LCD modules, you order the display and the corresponding backlight separately. This gives you a wealth of possible combinations. Designed for compact hand-held devices, this modern LCD range provides a number of real benefits with or without backlight: * extremely compact at 36,0x27,5 mm at the standard font size of 2.6 mm (4 x 10) * ultra-flat at 2.0 mm without backlight or 4.6 mm including LED backlight * SPI interface (2-/3-/4-wire) and IC (2-wire) * typical power consumption of only 440A in full operation (LED white backlight as of 3mA) * easy installation by simply soldering into the board * A whole range of design variants can be supplied as of single units * Changing background color LED BACKLIGHTS 3 different variants are available for Limiting resistor individual backlighting: amber, yellow- amber Forward Current EA LED36x28-A voltage max. green/red, green/red/white. 3,3 V 5V For the amber backlight, 2 separate LED Connected in parallel 2,1 V 60 mA 20 ohm 48 ohm paths are available, which can be switched Connected in series 4,2 V 30 mA - 27 ohm in parallel or in series to ideally match the system voltage. This means that all the Limiting resistor backlights can be run either at 3.3 V and green/red/white Forward Current higher voltages. EA LED36X28-ERW voltage max. 3,3 V 5 V Operation of the backlight requires an green path 3,0V 45 mA 7 ohm 45 ohm external series resistor for current limiting. red path 2,1 V 45 mA 27 ohm 65 ohm This can be calculated by R=U/I you will white path 3,0 V 30 mA 10 ohm 67 ohm find the values in the table. To improve life time it is recommanded to use a current source only. Limiting resistor yellowgreen/red Forward Current EA LED36x28-GR voltage max. The operating life of the yellow/green, red 3,3 V 5V and amber backlights is 100,000 hours and red path (AGR/CR) 2,1 V 45 mA 27 ohm 65 ohm that of the white backlight is a bit shorter. yellowgreen path (AGR/CG) 2,1 V 60 mA 20 ohm 48 ohm Important: Never operate the backlight directly on a 5 V/3.3V supply, as this can immediately destroy the LEDs INSTALLATION First, the display and the corresponding backlight are clipped together. The complete unit is then inserted into a PCB and soldered. Note that the 4 pins for the backlight must also be soldered from the top with less tin. Important: There are one or two protective films on the display (top and/or rear side) and one on each backlight. Those have to be removed during or after production. Page 2 Printing and typographical errors reserved. ELECTRONIC ASSEMBLY reserves the right to change specifications without prior notice.

All bezels are available with an anti-glare screen. The bezels are simply inserted into the frontal cutout. This gives your unit a professional look, and at the same time the anti-glare screen prevents the integrated display from being touched or getting dirty. The anti-glare screen makes the display considerably easier to read. Please refer to the tables for dotmatrix modules for the order numbers of the various bezels. You will find more information on bezels in our data sheet, which is available in PDF format, or on our accessories page.

Issue 10.2016 LCD-Modul 2x8 - 5.01mm INCL. CONTROLLER ST7066 Dimension 40 x 20 mm FEATURES * SUPER SMALL LCD MODULE * HIGH CONTRAST LCD-SUPERTWIST DISPLAY (BLUE/NEUTRAL) * OPTIONAL LED-BACKLIGHT YELLOW/GREEN * HD 44780 COMPATIBLE * 4- OR 8-BIT DATA BUS INTERFACE * ASCII CHARACTER SET BUILT IN * ALSO AVAILABLE: 1x8 LCD WITH SAME DIMENSIONS * POWER SUPPLY +5V OR 2.7V OR 3.3V 2mA and 50mA for LED-B/L (5V) * OPERATING TEMPERATURE RANGE EA DIPS082: -20+70C * OPERATING TEMPERATURE RANGE EA 8081-A3N: 0+50C * NO MORE MOUNTING REQUIRED: SIMPLY PLUG INTO PCB ORDERING INFORMATION LCD-MODULE 2x8 - 5.01mm EA DIPS082-HN WITH LED BACKLIGHT YELLOW/GREEN EA DIPS082-HNLED LCD-MODULE 1x8 - 7.15 mm EA 8081-A3N no more mounting required2x8 - 5.01mm Pinout Contrast setting Pin Symbol Level Function Pin Symbol Level Function 1 VSS L Power Supply 0V (GND) 8 D1 H/ L Display Data 2 VDD H Power Supply +5V 9 D2 H/ L Display Data 3 VEE - Contrast (about 0.3V / 1.2V) 10 D3 H/ L Display Data 4 RS H/ L H=Data / L=Command 11 D4 (D0) H/ L Display Data 5 R/W H/ L H=Read / L=Write 12 D5 (D1) H/ L Display Data 6 E H Enable (falling edge) 13 D6 (D2) H/ L Display Data 7 D0 H/ L Display Data / Anode LED-B/L 14 D7 (D3) H/ L Display Data, MSB LED Backlight Standard display EA DIPS082-HN is reflective, non-backlighted version. Module with part number EA DIPS082-HNLED comes with yellow/green LED backlight. Power consumption for backlight is 50mA typ. and 80mA max. Backlight is permanent switched on. Supply voltage with backlight is 5V only. For individual use LED backlight can be switched on and off after doing the following modification: Remove series resistor R5 and change resistor from R6 to R7. Now a positive voltage at pin 7 (D0) powers Anode of backlight direct. To limit LED-current an external series resistor is required (R = Ext. 0,8V / I ). Please note that in this case display interface is 4-bit mode only LED Table of commands Code Execute Instruction Description Time DB DB DB DB DB DB DB DB R/W RS 7 6 5 4 3 2 1 0 (max.) Clears all display and returns the cursor Clear Display 0 0 0 0 0 0 0 0 0 1 1.64ms to the home position (Address 0). Returns the Cursor to the home position (Address 0). Also returns the Cursor At Home 0 0 0 0 0 0 0 0 1 * display being shifted to the original 1.64ms position. DD RAM contents remain unchanged. Sets the Cursor move direction and specifies or not to shift the display. Entry Mode Set 0 0 0 0 0 0 0 1 I/D S 40s These operation are performed during data write and read. Sets ON/OFF of all display (D) cursor Display On/Off 0 0 0 0 0 0 1 D C B ON/OFF (C), and blink of cursor position 40s Control character (B). Moves the Cursor and shifts the display Cursor / Display Shift 0 0 0 0 0 1 S/C R/L * * 40s without changing DD RAM contents. Sets interface data length (DL) number of display lines (N) and character font Function Set 0 0 0 0 1 DL N F * * 40s (F). Sets the CG RAM address. CG RAM CG RAM Address Set 0 0 0 1 ACG data is sent and received after this 40s setting. Sets the DD RAM address. DD RAM data is sent and received after this DD RAM Address Set 0 0 1 ADD 40s setting. Reads Busy flag (BF) indicating internal Busy Flag / Address operation is being performed and reads 0 1 BF AC - Read address counter contents. CG RAM / DD RAM 1 0 Write Data Writes data into DD RAM or CG RAM 40s Data write CG RAM / DD RAM Reads data from DD RAM or CG RAM 1 1 Read Data 40s Data Read Page 2 Printing and typographical errors reserved. ELECTRONIC ASSEMBLY reserves the right to change specifications without prior notice.