1.8 inch st7735r spi 128 160 tft lcd display brands

Specification:Driver IC: ST7735RResolution: 128 x 160 pixelsFeatures:- Can help you to get rid of the Arduino serial monitor.- Some tests and provide UTFT library, AdaFruit Library and instruction on DropBox.- Tested with Latest Arduino 1.6.5.IO interface:1. RESET --directly to the microcontroller IO2. CS --directly to the microcontroller IO3. A0 --IO control registers select4. SDA --IO control data transmission5. SCL --IO control SPI bus6. BL--High Level 3.3V backlight onNote:Please contact us for documents and driver if you need. Please noted this LCD is 3.3V, which can not receive 5V signals from the Arduino, so please use a 1k series resistors between GPIO lines on a 5V arduino and this LCD, power this LCD with 5V but drive it with "level shifted resistor" GPIO lines.Besides, you could use mcifriend 2.8 inch TFT LCD library to get it to work, it will work fine with the Mega or Uno.

AllAnalog to Digital ConvertersArduino Starter KitsBatteriesBattery Charger ModuleBreadboardButton Key ModuleBuzzerCamera ModuleCapacitor &nbspCeramic Capacitors &nbspElectrolytic CapacitorsCases &nbspBattery HolderConnectors &nbspJumper Wires &nbspTact SwitchCooling FanDevelopment Boards &nbspArduino Development Boards &nbspRaspberry Development Boards &nbspSTM32 BoardsDiodesFingerprint SensorIntegrated Circuit &nbspAmplifier module &nbspCurrent Voltage Tester &nbspMicro SD Storage Expansion Board &nbspReal Time Clock Module &nbspRelay Module &nbspST TIP NXPInternet Of ThingsJoy StickLaser ModuleLEDMemory ModulesMP3 Decoding board &nbspMP3 Player ModuleMulti Coin Accetor/SelectorOptoelectronic Displays &nbspLCD ModulesPCB BoardsPCB Connectors &nbspFemale Single Row Pin HeaderPotentiometer &nbspPotentiometer Adjustable ResistorPotentiometer Knob CapPower AdaptorsPower Regulator Modules &nbspStep Down ModuleProgrammer module &nbspUSB To TTL Serial Adapter Module &nbspUSB to UART TTL ModuleProximity sensorPumpsResistor &nbspMetal Film Resistor &nbspPhotoresistor Light Dependent Resistor LDRRobotics & Aeronautics &nbspMotors and ActuatorsSensors &nbspCurrent Sensors &nbspDoor Window Sensor &nbspGas Sensor &nbspHumidity Sensor &nbspInfrared Light Sensor Module &nbspIR Infrared Obstacle Avoidance Sensor Module &nbspLoad Cell Weighing Sensor &nbspMicrophone Sound Sensor &nbspPIR Motion Sensor &nbspPulse Sensor Module &nbspRain Water Sensor Module &nbspReed Sensor Module &nbspSensor Shield Expansion Board &nbspShake Vibration Sensor Module &nbspSoil Moisture Sensor &nbspSpeed Sensor &nbspTemperature Sensor &nbspTouch Button Module &nbspTouch Sensor Module &nbspUltrasonic Distance Sensor &nbspVibration Sensor Module &nbspVoltage Sensor Module &nbspWater Level Sensor &nbspWeighing Sensor ModuleServo Shield ModuleSIGNAL FREQUENCY MODULESolar Devices &nbspSolar PanelSolenoid LockSolenoid ValveStepper Driver ChipTools &nbspDigital Multimeter &nbspMeasurement & Analysis Instruments &nbspSoldering ToolsTransistorsUncategorizedUsb Wi-fi AdapterVoice RecorderWater Flow SensorWireless Devices &nbspBluetooth & Infrared Devices &nbspESP32 Modules &nbspGPS/GSM/GPRS Devices &nbspIR Remote &nbspRFID/ RF/ WIFI Devices &nbspWireless Transceiver

A wide variety of tft display 1.8 options are available to you, You can also choose from original manufacturer, odm and agency tft display 1.8,As well as from tft, ips, and standard.

This is a 1.8" inch ST7735R SPI 128160 TFT LCD Display Module With PCB. It has a durable hard PCB board and metal, ideal for 1602 interface. This is welded by reflow soldering, no burrs, comfortable and safe. The power supply IC and SD card slot, convenient to use. The transparent protective film covered on the display protect it from damage. Suitable for beginners of LCD colour display module, SCM learners and LCD enthusiasts.

Note:Please contact us for documents and driver if you need them. Please note this LCD is 3.3V, which can not receive 5V signals from the Arduino, so please use a 1k series resistors between GPIO lines on a 5V Arduino and this LCD, power this LCD with 5V but drive it with "level-shifted resistor" GPIO lines.

The 1.8" display has 128x160 color pixels. The TFT driver (ST7735) can display full 18-bit color. The breakout has the TFT display soldered on (it uses a delicate flex-circuit connector).

In the below example, Node32-Lite and this 1.8-inch LCD. Please refer to the tutorial here: ST7735S interfacing with ESP32 to make the connections, Arduino library installation, and modification needed for it to works on this LCD.

The 1.8" display has 128x160 color pixels. The TFT driver (ST7735) can display full 18-bit color. The breakout has the TFT display soldered on (it uses a delicate flex-circuit connector)

In the above example, Node32-Lite and this 1.8-inch LCD.  Please refer to the tutorial here: ST7735S interfacing with ESP32 to make the connections, Arduino library installation, and modification needed for it to works on this LCD.

The 1.8inch LCD uses the PH2.0 8PIN interface, which can be connected to the Raspberry Pi according to the above table: (Please connect according to the pin definition table. The color of the wiring in the picture is for reference only, and the actual color shall prevail.)

ST7735S is a 132*162 pixel LCD, and this product is a 128*160 pixel LCD, so some processing has been done on the display: the display starts from the second pixel in the horizontal direction, and the first pixel in the vertical direction. Start to display, so as to ensure that the position corresponding to the RAM in the LCD is consistent with the actual position when displayed.

The LCD supports 12-bit, 16-bit and 18-bit input color formats per pixel, namely RGB444, RGB565, RGB666 three color formats, this routine uses RGB565 color format, which is also a commonly used RGB format

Note: Different from the traditional SPI protocol, the data line from the slave to the master is hidden since the device only has display requirement.

Framebuffer uses a video output device to drive a video display device from a memory buffer containing complete frame data. Simply put, a memory area is used to store the display content, and the display content can be changed by changing the data in the memory.

If you need to draw pictures, or display Chinese and English characters, we provide some basic functions here about some graphics processing in the directory RaspberryPi\c\lib\GUI\GUI_Paint.c(.h).

Set points of the display position and color in the buffer: here is the core GUI function, processing points display position and color in the buffer.

The fill color of a certain window in the image buffer: the image buffer part of the window filled with a certain color, usually used to fresh the screen into blank, often used for time display, fresh the last second of the screen.

Display time: in the image buffer,use (Xstart Ystart) as the left vertex, display time,you can choose Ascii visual character font, font foreground color, font background color.;

2. The module_init() function is automatically called in the INIT () initializer on the LCD, but the module_exit() function needs to be called by itself

Python has an image library PIL official library link, it do not need to write code from the logical layer like C, can directly call to the image library for image processing. The following will take 1.54inch LCD as an example, we provide a brief description for the demo.

Note: Each character library contains different characters; If some characters cannot be displayed, it is recommended that you can refer to the encoding set ro used.

The first parameter is a tuple of 2 elements, with (40, 50) as the left vertex, the font is Font2, and the fill is the font color. You can directly make fill = "WHITE", because the regular color value is already defined Well, of course, you can also use fill = (128,255,128), the parentheses correspond to the values of the three RGB colors so that you can precisely control the color you want. The second sentence shows Micro Snow Electronics, using Font3, the font color is white.

The demo is developed based on the HAL library. Download the demo, find the STM32 program file directory, and open the LCD_demo.uvprojx in the STM32\STM32F103RBT6\MDK-ARM directory to check the program.

For the screen, if you need to draw pictures, display Chinese and English characters, display pictures, etc., you can use the upper application to do, and we provide some basic functions here about some graphics processing in the directory STM32\STM32F103RB\User\GUI_DEV\GUI_Paint.c(.h)

Image buffer part of the window filling color: the image buffer part of the window filled with a certain color, generally as a window whitewashing function, often used for time display, whitewashing on a second

Display time: in the image buffer,use (Xstart Ystart) as the left vertex, display time,you can choose Ascii visual character font, font foreground color, font background color.

DEV_Config.cpp(.h): It is the hardware interface definition, which encapsulates the read and write pin levels, SPI transmission data, and pin initialization;

image.cpp(.h): is the image data, which can convert any BMP image into a 16-bit true color image array through Img2Lcd (downloadable in the development data).

The hardware interface is defined in the two files DEV_Config.cpp(.h), and functions such as read and write pin level, delay, and SPI transmission are encapsulated.

For the screen, if you need to draw pictures, display Chinese and English characters, display pictures, etc., you can use the upper application to do, and we provide some basic functions here about some graphics processing in the directory GUI_Paint.c(.h)

Display time: in the image buffer,use (Xstart Ystart) as the left vertex, display time,you can choose Ascii visual character font, font foreground color, font background color.