2.8 tft lcd touch shield module for arduino blue brands

This website is using a security service to protect itself from online attacks. The action you just performed triggered the security solution. There are several actions that could trigger this block including submitting a certain word or phrase, a SQL command or malformed data.

ER-TFTM028-4 is 240x320 dots 2.8" color tft lcd module display with ILI9341 controller board,superior display quality,super wide viewing angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO,ARM and Raspberry PI.It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.

It supports 8080 8-bit /9-bit/16-bit /18-bit parallel ,3-wire,4-wire serial spi interface.Built-in optional microSD card slot, 2.8" 4-wire resistive touch panel with controller XPT2046 and 2.8" capacitive touch panel with controller FT6206. It"s optional for font chip, flash chip and microsd card. We offer two types connection,one is pin header and the another is ZIF connector with flat cable mounting on board by default and suggested. Lanscape mode is also available.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!".Here is the link for 2.8"TFT Touch Shield with Libraries, EXxamples.Schematic Diagram for Arduino Due,Mega 2560 and Uno . For 8051 microcontroller user,we prepared the detailed tutorial such as interfacing, demo code and development kit at the bottom of this page.

might not be quite right, as the USE_MEGA_16BIT_SHIELD (using the special driver) had to be #define"d, along with the Identifier to 0x9595. (To be precise, I"ve already did this with my board that came in previously, with no avail.)

With that being said, ArekJan"s modified UTFT library to support the Hirax 8347-I now works too, straight out of the box, without any alterations to the source code. I"m mentioning this for the other unfortunate souls reading this forum: if your 8347-I display, similar to mine, stays white, no matter which library you get, try my approach (MCUFRIEND_kbv with the define and the proper Identifier, or the UTFT-8347i library). If they don"t seem to do anything, your display is a DOA, ready to be shipped back to the seller.

We guarantee your satisfaction on every product we sell with a full refund — and you won’t even need a receipt.* We want you to be satisfied with your Micro Center purchase. However, if you need help or need to return an item, we’re here for you!

If an item you have purchased from us is not working as expected, please visit one of our in-store Knowledge Experts for free help, where they can solve your problem or even exchange the item for a product that better suits your needs.

*If you are a Micro Center Insider or if you have provided us with validated contact information (name, address, email address), you won’t even need your receipt.

Description:; This is a 2.8 inch TFT LCD expansion board. This display has a controller built into it with RAM buffer so that almost all work is done by the TFT.; It leads out the pins of the TFT and pins; is 2.54 mm, so the secondary development is easy. With the GPRS module, you can design your phone. With the NFC reader module, you can create access control systems with the photos show. With voltage and current sensors, you can make an oscilloscope.;

- Compatibility: Because the logic level is 3.3V, it is compatible with 3.3V; for; Arduino board, you generally need to add a level conversion circuit if you use a 5V; for; Arduino Board (for; Arduino UNO R3 /; for; Arduino Mega2560 /; for; Arduino Leonardo).

IO Port Package: PAD is available, and the pin; is 2.54 mm. - LED pin can connect to external backlight control circuit to control the brightness of backlight. You can connect it to GND to turn on the backlight. - Very suitable for digital photo frame, oscilloscope, function generator, detection system monitor

This website is using a security service to protect itself from online attacks. The action you just performed triggered the security solution. There are several actions that could trigger this block including submitting a certain word or phrase, a SQL command or malformed data.

This is a 3.0 inch TFT LCD expansion board. This display has a controller built into it with RAM buffer, so that almost all work is done by the TFT. It leads out the pins of the TFT and breakout pins pitch is 2.54mm, so the secondary development is easy.

- Compatibility: Because the logic level is 3.3V, it is compatible with 3.3V Arduino board, you generally need to add a level conversion circuit if you use a 5V Arduino Board (UNOR3 / Mega2560 / Leonardo).