what should be used to clean lcd monitors quotation

Don"t make the mistake of thinking that LCD screens work like your nifty new iPad. In general, touching should be off limits because pressing too hard on the screen can actually break or crack pixels. So the first rule to cleaning an LCD screen is don"t do it unless you have to (i.e. unless it"s actually dirty).

Many retailers offer special cleaning solutions for LCD screens, but the truth is that most of these are made up primarily of water. So, if you don"t want to take the time to go buy a cleaner or you want to save the money (maybe to put toward that "What Not to Wear" dress), you can just make your own LCD cleaner by mixing water with some vinegar or isopropyl alcohol -- the solution should be no more than 50/50.

You could even start with plain water and see if you need the vinegar or alcohol, which will come in handy when you"re trying to wipe away greasy fingerprints. Some people recommend only using distilled water, but regular water works fine, according to Dave Chipman from Sharp.

Unless you want to end up with a melted, discolored, hazy or scratched LCD screen, steer clear of all spray cleaners. In particular, don"t use any solvent cleaners that include acetone, ethyl alcohol, ethyl acid, ammonia or methyl chloride. You also want to avoid using any materials that could potentially scratch the screen"s delicate surface. Opt for a soft, clean, cotton cloth instead of wood-based products like paper towels and tissues. Chipman suggests using a microfiber cloth for best results.

If you"re lucky enough to have a service come in and do your cleaning for you, make sure they don"t inadvertently ruin your television or monitor by trying to clean it with something like glass cleaner. You should either take the time to explain -- and maybe even demonstrate -- how you want your LCD screen cleaned or just ask your cleaner to leave this particular job for you.

We"ve all had that moment: You"re sitting at your computer or laptop and the light hits your screen in a way to reveal an unsightly accumulation of streaks, fingerprints, and dust.

To help, we round up the most important things to know about cleaning your computer screen, whether it"s a Mac or PC. While it"s a simple process, there are a few important rules to keep in mind to make sure you"re doing it safely.

Computer screens are not all made the same, and thus can"t all be cleaned the same way. You"ll want to be careful no matter your screen type, but it"s helpful to know that displays come in two categories:Glass-coated screens: The screens on newer iMac displays and MacBooks have a glass overlay. Glass displays are a little less delicate than LCD or LED screens, and mild cleaning solutions, like rubbing alcohol, are generally safe to use on them.

LCD or LED screens:Windows computers and most touchscreens and matte displays are typically not coated in glass. Extra care should be taken with these screens so not to damage the pixels that make up the display.

Since there are so many computers, laptops, and monitors out there, each with their own set of variables and specificities, it"s smart to just simply err on the side of caution.

To clean a computer screen, you really just need two things: A microfiber cloth and filtered or distilled water. That"s to say you don"t need a special store-bought cleaning solution.

If you"d like some extra sanitation power, an equal parts mixture of water and vinegar is safe no matter your screen type. If you know that your display is glass-coated, you can also use an equal parts mixture of water and 70% rubbing alcohol.What you needTwo lint-free microfiber cloths

d3sign/Getty ImagesTurn the computer or laptop off.For safety reasons, begin by letting the device cool down completely. Dust, fingerprints, and smudges are also easier to spot on a black screen.

Wipe off dust with a dry cloth. Use a dry, lint-free microfiber cloth to gently wipe away any visible dust and dirt. If necessary, apply gentle pressure to remove surface-level smudges.

If any marks remain, wipe with a lightly moistened cloth.For glass-coated screens, you can use a mixture of equal parts water and vinegar or rubbing alcohol. For LED or LCD screens, use only water. Spray or lightly dab the solution directly onto the cloth and carefully wipe the screen from left to right.

Buff with a dry cloth and air-dry.If any streaks remain once the screen dries, gently buff them with the dry cloth. Before you turn your computer or laptop back on, allow the screen to dry completely.Note:Apple claims that you can use 70% isopropyl disinfecting wipes to clean any Apple product. Just remember not to get any liquid into the device"s ports or openings — to avoid this, you might want to wring out the wipe to remove any excess liquid before using it.

For the best advice for cleaning your screen, it"s a smart idea to check your owner"s manual, which provides the manufacturer"s specific recommendations. But since screens are especially susceptible to damage, there are a few general guidelines that apply, no matter the type of screen you own.

Turn off your computer before cleaning the screen. This is just safe practice where any amount of liquid is involved, but more specifically, any static on the screen could create a shock and damage the internal components.

Do not use abrasive cleaning solutions. This includes bleach (or any products containing bleach), hydrogen peroxide, or all-purpose spray cleaners. Using an abrasive cleaner can ruin the finish of your screen.

Use only soft microfiber cloths.Even a fabric as soft as a cotton shirt has snags and uneven particles that can scratch a computer screen. For this reason, avoid T-shirts, towels, and paper towels. The exception is the Apple Pro Display XDR or iMac, which requires a special polishing cloth.

Never spray cleaning solution directly onto the screen. To avoid any risk of damage from excess moisture, mist the solution directly onto the microfiber cloth instead.

Do not wipe in circles. Wiping in circles can create uneven pressure and ultimately lead to screen damage. It"s also more likely to create streaking. Wipe in tight, Z-shaped motions, or in broad strokes from side to side.

Melanie Weir is a freelance author for Insider, mainly focusing on the Tech Reference section, but occasionally contributing to Lifestyle and Entertainment topics as well. She is also a freelance writer for ScreenRant, and is the Lead Weekend News Editor at TheThings.com. In her spare time she writes plays for both stage and screen. She can be reached at melanie.weir1008@gmail.com, or through LinkedIn.

Use a non abrasive cleaning solution, diluting isopropyl alcohol (not rubbing alcohol, as it may contain oil) into a solution of 50% alcohol and 50% with distilled water water (or purified/bottled water). You could also buy a cleaning solution that does not contain bleach, ammonia, or vinegar.

Before you start, power-off and unplug your monitor. Spray the cleaning solution on a soft cloth (for example an old T-shirt), lint-free microfiber cloth, or some other very soft cloth. A large cloth is best, since it will help reducing the risk of leaving streaks across the display from finger pressure.

Starting from the top, wipe the screen in one direction until you have cleaned the entire screen. Apply light, but distributed pressure. Repeat if necessary. Let it air dry.

Even if you don"t have snot-nosed kids or wet-nosed pets, your computer monitor or HDTV panel will eventually accumulate a collection of annoying smudges and stains. My household happens to contain both of the aforementioned creatures and, thus, I"ve developed a method for wiping down the HDTV in the living room and the LCD monitor in my office, as well as the screen of my laptop and iPad.

If you take a quick survey of LCD or HDTV manufacturers about the recommended method for cleaning the surface of your monitor or TV screen, you"ll discover more don"ts than dos, often in conflict with one another.

In the don"t column:Don"t use aerosol sprays, solvents, or abrasives. (This means don"t reach for the Windex under the kitchen sink, as tempting as it may be.)

First, attempt to clean your screen with a dry, lint-free cloth. If you can"t find the cleaning cloth that came with your screen in question, then it"s likely you have one laying around from a laptop, iPad, or iPhone purchase.

After removing any dust from your screen with a dry cloth, dip the other cloth in your dish soap solution, wring it out, and gently wipe your display. Next, rinse out your soapy cloth, wring it out again, and wipe your display to remove any soap residue. Finally, take your dry cloth and wipe the display to remove any streaking.

Editors" note:It"s time for spring cleaning! Week"s two"s theme: physical cleaning.Check backevery day this week to see how best to keep dirt, grime, crumbs, and other annoying bits off your devices. And be sure to return next week for more spring cleaning tips and tricks.

Remember when your LCD or OLED display had that brand-new, fresh-out-of-the-box shine, feel and look? You are in the right place if your display is now due for deep cleaning.

Things to consider before cleaning or handling an electronic displayAvoid static by grounding your body and following proper ESD-safe handling techniques.

A microfiber cloth and distilled water is recommended for cleaning the display glass. Use Qtips and Isopropyl alcohol for cleaning the printed circuit board.

Although distilled water is recommended for wiping the display glass, you can use a cleanser developed explicitly for cleaning displays. However, do not spray it directly onto the display. Spray a tiny amount of the cleaner onto a microfiber cloth first to avoid getting any cleaning solution inside the display.Never spray any liquids directly onto the display.A spray is too hard to control and confine. The fluids can seep into the other display layers or surrounding components and cause irreversible liquid damage.

Only use a microfiber cloth and don"t use chemicals to clean a resistive touchscreen.Disconnect the display from the power supply and remove any screen protectors or liners.

Isopropyl alcohol (IPA) is widely used to clean printed circuit boards (PCBs). Use a Q-tip or soft small bristle brush for scrubbing a PCB, and never use a paintbrush.Gently rub a Q-tip in Isopropyl alcohol.

Cleaning soldering residue on LCD with Isopropyl alcohol and a Q-Tip.Cleaning residue around soldering elements is not necessary if Newhaven Display performed the soldering.

Cleaning your electronic display is a simple task. However, it is essential to consider these steps to handle and clean it properly. You should now have a better understanding of what cleaning products are safe to use, how to clean the display screen glass, how to clean touchscreens and how to clean soldering residue.

Responsible for performing installations and repairs (motors, starters, fuses, electrical power to machine etc.) for industrial equipment and machines in order to support the achievement of Nelson-Miller’s business goals and objectives:

• Perform highly diversified duties to install and maintain electrical apparatus on production machines and any other facility equipment (Screen Print, Punch Press, Steel Rule Die, Automated Machines, Turret, Laser Cutting Machines, etc.).

Regularly cleaning your LCD monitor keeps it free of dust, smudges, and germs. Wiping with a dry microfiber cloth is the safest cleaning option and is surprisingly effective at removing germs. You may need to use a dampened microfiber cloth to get rid of stubborn smudges and stuck-on debris, though. If you"re worried about germs, consider using a vinegar and water solution or a Lysol wipe on the screen. Be sure to check the device’s user manual first to make sure it’s okay to use liquids!

This website is using a security service to protect itself from online attacks. The action you just performed triggered the security solution. There are several actions that could trigger this block including submitting a certain word or phrase, a SQL command or malformed data.

This website is using a security service to protect itself from online attacks. The action you just performed triggered the security solution. There are several actions that could trigger this block including submitting a certain word or phrase, a SQL command or malformed data.

During these unprecedented times, it is crucial to stay up to date with any and all methods to stay healthy. Here at TRU-Vu, we value our customers’ health and safety. For this reason, we have put together some guidelines for cleaning and disinfecting TRU-Vu touch screen monitors.  This can be achieved without causing any damage to the touch screen

To begin with, it is important to distinguish cleaning from disinfecting. Cleaning removes dirt, germs, and impurities. Cleaning does help to reduce germs that can lead to infection, it does not kill the germs or virus. Disinfecting utilizes chemicals to kill germs to reduce/eliminate the chance of infection.

The U.S. Centers for Disease Control and Prevention (CDC) states: “diluted housed bleach solutions, alcohol solutions with at least 70% alcohol, and most common EPA-registered household disinfectants should be effective” for disinfecting surfaces to prevent the spread of coronavirus (COVID-19).

Be sure to not get any liquids inside of the unit. To best avoid doing so, do not directly spray the monitor. Either use wet wipes, or spray/dampen a cloth with water or gentle cleaner and be sure to squeeze any excess moisture off.

Avoid using abrasive cloths, such as rags or paper towels, as they can spread lint and/or even damage the screen. Instead, use only non-abrasive cloths, such as soft lint-free cloth, in order to avoid scratching the monitor.

Dampen a new clean, non-abrasive cloth with a disinfectant recommended by the CDC: a household bleach solution (1/3 cup of bleach per gallon of water) or Isopropyl alcohol ( 71% to 85% alcohol). Be sure to squeeze any excess liquid off of the cloth. Do not spray the solution directly onto the touch screen.

More information about recommended disinfectants for COVID-19 from the EPA can be found at: https://www.epa.gov/pesticide-registration/list-n-disinfectants-use-against-sars-cov-2

Apply the solution to a soft cleaning cloth; do not spray directly onto the touch screen. Wear gloves during the cleaning process. Finally, discard both the gloves and the cleaning cloth following the cleaning process.

Certainly, If you have any questions, or require further assistance with cleaning your TRU-Vu touch screen monitor, please contact us at #847-259-2344.

With over 540 LCD monitors and touch screens on our site, selecting the ideal equipment, or touch screen solution may be a bit overwhelming.To help narrow-down the choices, check out ourAdvanced Search Tool.For example, this enables you filter by your own specific search requirements.

Our monitor cleaning technicians provide cleaner and crisper services that help to reduce eyestrain. Our services at UKDCC including cleaning all types of monitors and screens whether they are TFT monitors, Plasma screens or even traditional style CRTs. The monitor housing is externally cleaned and sanitised and then the screen is cleaned with the special screen cleaning materials.

The computer screens and monitors often attract fingerprints, from employees pointing at things. Our computer cleaning services improve visibility and reliability of computer monitors and screens. Our cleaning methods Improve safety and reduce the potential risk of fire due to building up dust and overheating. Call our computer monitor/ screen cleaning team for free no obligation quotation or book a free no obligation survey with us.

Our cleaning solutions have the anti-bacterial agent that is most effective against germs commonly found on IT equipment. We also use special anti-static solutions for screens. The anti-static solvent is used to clean all plastic casings on the monitor. The screen is cleaned and anti-static treatment applied. If a glass screen radiation filter is fitted, this is removed and treated with a specially formulated screen cleaner.

If it is accessible all cables and connections will be wiped and filters and fans on the drive will be cleaned. Compressed gas, brush and/or vacuum cleaner are used to remove dust and debris from the monitors, followed by the minimum use of solvents, using impregnated cloths, to clean the frames.

Keeping your computer clean is a necessary habit. Over time, your computer — especially your monitor — collects dust and debris, not to mention passing germs from sneezing and coughing. While fingerprints are bad enough, the eye strain from a messy monitor is even worse.

Cleaning your monitor is also a bit more involved than a simple wipe-down, and there are certain products you shouldn’t use. In this article, we’re going to talk about the right way to clean your computer monitor.

While it may be tempting to reach for a bottle of Windex or some other general cleaning product, don’t! Harsh chemicals may be fine for windows or countertops, but they can wreak havoc on computer monitors, wearing away coatings. There are many cleaning fluids on the market specifically geared toward computer monitors. While these products indeed work, you don’t need to spend money on them if you don’t want to; distilled water should work for most monitor-cleaning, and you can mix in some white vinegar for stubborn grime.

Additionally, avoid paper towels, rags, old T-shirts, or any of the usual materials you use to wipe down surfaces in your home. Monitors are more delicate than they look, and these fabrics — even paper towels — are abrasive enough to scratch your screen, especially if you have used them for other jobs where they might have accumulated grit. A microfiber cloth — the kind you might use to clean your glasses or vinyl records — is the safest choice. Just make sure it’s free of any dirt or grime before swiping across your display.

Step 1: Turn off your monitor. It’s easier to see smudges and stuff on a black screen, so turning off your monitor makes it easier to see what you are doing. It’s also safer for you and your computer. Cleaning your monitor while it’s on and the pixels are all fired up could damage your screen or potentially give you an unpleasant electrical jolt. Please turn it off!

Step 2: Wipe your monitor with a microfiber cloth. If dust is the only thing on your screen, a quick wiping should be enough to clean it. Take the microfiber cloth and gently brush the screen in long motions. We cannot stress enough that you should be gentle: Pressing too hard on the screen could damage the pixels within.

Step 3: If the thick layer of dust on your monitor has been slowly replaced with more questionable gunk — maybe some dried mucus from a sneeze that caught you off guard or mysterious specs of who-knows-what — then you’ll want to use cleaning fluid.

There are gentle cleaning fluids designed for monitors, but distilled water works well, as mentioned earlier. It’s important you only use filtered or distilled water, however, since tap water contains minerals and other substances that can harm the screen or leave annoying streaks. For especially stubborn grime, add a bit of white vinegar to the water. Just be careful not to spill any on your laptop.

Step 4: It’s important that you never spray water or other cleaning fluids directly onto your monitor, or it might trickle down to the edge of the screen and seep into the monitor itself and damage the electronic components within.

A thorough but gentle procedure is carried out on the front and back of the monitor screen to remove dirt, dust, and residues, and to give the monitor panel a fresh look and to restore the picture and visual quality of the screen.

LCD and LED screens are made of plastic materials, unlike the big shiny curved glass tubes of yesteryear. This soft plastic film is vulnerable to scratches, damage by sharp articles, and/or improper cleaners. All these screens require special attention to clean properly and safely.

• Do not use Kleenex, paper towels, sponges, or other coarse shop towels! These materials may contain abrasives that can scratch the surface coatings as well as leaving lint on your screen.

• To clean your antistatic screen, lightly dampen a soft, clean cloth with water. If possible, use a special screen-cleaning tissue or solution suitable for the antistatic coating. Do not use benzene, thinner, ammonia, abrasive cleaners, or compressed air.

If you spend any time on your computer, you’ve probably noticed that your screen can become rather filthy over time. Not knowing how to clean a computer screen is usually what puts most people off doing so.

Many people are afraid that they’ll damage their monitor by cleaning it, which simply isn’t true if you know how to clean a monitor screen properly. Leaving your screen filthy can interfere with work, gameplay, movie watching, and many other computer-related tasks.

A dirty screen can be distracting, and if it’s in your office it can make it appear untidy. Therefore, learning the best way to clean a monitor screen will not only stop you from becoming distracted when using your computer but also enhance the overall appearance of your office.

This ultimate guide to cleaning a computer screen will tell you everything you need to know to keep your screen spotless without the fear of damaging it. If you require office cleaning services in London or throughout the UK, then please get in touch.

Stay away from window cleaning products.This is an important piece of advice that is relevant to many people. Most people assume that because their screen is made of glass, then window cleaning products are the best thing to clean them with.

However, this isn’t the best way to clean a monitor and may cause damage. Although window cleaning chemicals can be okay to use on other items that contain glass, computers aren’t one of them.

Computer screens are often coated with special protective materials or materials to enhance the appearance of what they project to the user. Using chemicals can cause a breakdown in these protective coatings and cause irreversible damage to your monitor.

Some computer supply companies stock these products, or you may be able to get hold of them through commercial cleaning companies. You should only use cleaning chemicals that specifically state that they are designed for cleaning computer monitors.

If you are in a commercial environment then you’ll want to use the computer cleaning products available to keep your systems in the best condition. If you are in a home environment, however, distilled water and vinegar can be a good solution for cleaning your monitor without buying specialist products.

You should be aware, however, that this probably isn’t the best solution for a commercial environment as the smell of vinegar can linger for some time.

Although rags can be good to wipe down hard surfaces in the home or office, they have no place in your computer cleaning routine. Furthermore, you may also like to clean with paper towels or other disposable paper-based products, this is another no-no.

Paper products and rags can contain rough fibres that can scratch computer screens or break down protective coatings over time. The same principle that applies to eyeglasses also applies to computer screens – any cloth that isn’t soft or made of microfibre generally isn’t a good choice for cleaning a monitor.

If you’re an office manager then you likely have a team of people working on computers regularly that you manage. Ensuring your team has clean devices to work from may sound like a minor concern but it can have an impact on your team’s productivity.

If your team is working in a clean environment, then their morale is likely to be higher and in-turn productivity and work quality will also improve. Keeping monitors clean is also important in terms of the company’s appearance and helps systems hold their value if they are to be sold in future when you upgrade.

If your office has regular visitors then you’ll want to keep it spotless, as a dirty workplace doesn’t have a great effect on your professional image.

If you choose to clean your computer screens yourself, then it’s best to follow a step-by-step routine to ensure that your cleaning process is consistent. Follow the below steps when cleaning your monitor(s):

Removing dust is important before you start to add any cleaning solution to your screen. Dust can scratch your screen if you put too much pressure on your cloth, so removing dust should be done carefully. Use a microfibre cloth to remove any dust slowly by moving the cloth in circular motions.

Once the dust has been removed, add your cleaning solution to the cloth and then start to wipe off any grime that you can see on the screen. You should work in slow circular motions again and avoid putting too much pressure on the screen. If there are smudges, don’t scrape these, instead, go over them again. You may need to repeat the process several times to remove all dirt and grime from the screen.

Keeping your monitors clean is something that can be difficult, particularly if you work in an office environment. Having the time to clean multiple screens regularly can be impossible for anyone with a busy schedule.

In these instances, it can be a good idea to call in the help of a specialist cleaning team that use computer-safe products and are used to keeping offices clean. If you want to minimise the chances of computers becoming dirty, then it’s a good idea to ensure that employees are not allowed food at their desks and that they wash their hands thoroughly after food breaks.

If you take a closer look at your flat screen TV, you may be surprised by all the dust, dirt, and fingerprints across the screen and on the housing. When the lights are down and you’re watching your favorite movies, it may not be so noticeable, but the truth is it affects your viewing pleasure—and your TV’s performance and life span.

Your television is a commonly missed cleaning spot, but it’s a project that should be on your monthly cleaning checklist. Let’s discuss how to clean a TV screen, the housing, and the connections for audio/video equipment.

Most of our “how-to” cleaning posts start with a list of supplies and information you need to know before you get down to business. But learning how to clean a flat screen TV is a bit different from most cleaning chores. That’s because cleaning a LCD, LED, or other flat screen TV incorrectly could shorten its lifespan, affect performance, or even cause damage.

Instead of starting with what to do, we’re going to begin our guide for how to clean a TV screen with what not to do when learning how to clean a flat screen TV.

If you don’t take certain precautions when you clean that beautiful 65” LED screen, you might be better off leaving it dirty. Here’s a list of “don’ts” that will help you learn how to clean a flat screen TV the right way:

Don’t clean a flat screen when the TV is still warm. If you try to clean a warm screen with a screen cleaner, it could make removing dirt and grime more difficult and even cause damage.

Don’t use window or glass cleaner or any cleaner containing alcohol, benzene, ammonia, or acetone. Harsh chemicals can degrade anti-reflective and protective coatings, cause clouding, or even ruin the screen itself.

Don’t use cleaning pads, regular cleaning cloths, or paper towels, because the mildest abrasion can scratch coatings and screens. Even a paper towel can be fairly abrasive and cause buffed areas and fine scratches on flat screen TVs./li>

Don’t spray water or other liquids directly on your TV. Flat screen TV screens are made from layers of plastic, glass, adhesives, coatings, and other delicate materials. When liquid touches the edges of the screen, the moisture can wick into the layers and ruin the TV.

Don’t rub the flat screen too hard or press into the screen. Flat TV screens aren’t too fragile, but they can be damaged if you press too hard when you’re cleaning.

Whether you use a commercial TV screen cleaner or mix your own, keep in mind that chemicals and moisture are hazardous to your TV. Read your TV model’s instruction manual for cleaning guidelines. If you’ve misplaced your manual, you can locate it online. Look on the back of your set to determine its model number and Google the manual for that model.

The best way to clean a TV screen is to start with a dry cleaning method. Don’t forget, keep all hands off the TV screen as the less you touch your TV screen, the better. Follow the steps below and you should be able to get rid of most dirt and grime without worrying about damage to your flat screen.

For safety and a better view of those fingerprints and dirt, don’t forget to turn off your TV before you clean it. Unplug the set for good measure. Cleaning a flat screen while it’s warm could cause streaking, residue buildup, and other problems. If you have a plasma TV, you may have to wait up to 20 minutes for it to cool down completely. When you cut the power, you also reduce the risk of any moisture coming in contact with your TV’s wiring and causing an electrical issue.

Before you clean your flat screen TV, it’s essential to remove as much dust and dirt as possible without touching the screen. That’s because even the finest dust can scratch your TV’s coatings and screen if you move it around with your cleaning cloth. Use a can of compressed air to remove as much dirt from the screen as possible. Hold the can upright, about a foot from the screen, and spray away. The blasts of air will remove electrostatic-charged dust particles and are particularly good at cleaning out the screen corners.

Lightly wipe the flat screen with a clean, dry microfiber cloth. If possible, get your hands on one of those smooth microfiber cloths used for glass and lens cleaning (like the ones that come with new eyeglasses). A gentle wiping with a microfiber cloth should get rid of most fingerprints, smudges, and grime.

Most TV screens are somewhat flexible, so it’s difficult to know how much pressure you’re using on a particular spot. Clean with a light touch using a broad wiping motion either left and right or up and down. If you make circular buffing motions, you risk creating buff marks on the surface.

If cleaning your TV with a dry microfiber cloth still leaves smudges, dirt, and fingerprints, you’re going to need more cleaning muscle. Keep reading to find out what to clean a TV screen with to get rid of tough dust and dirt.

Remember: Moisture can be deadly for flat screen TVs, so only use as much TV screen cleaner as necessary. Here’s a screen cleaner you can make at home and the tools you need for a deeper flat screen TV cleaning:

For tough grime and fingerprints on a flat screen TV, one part distilled water and one part white distilled vinegar is a safe and effective cleaning solution. Barely dampen half of a clean microfiber cloth with your screen cleaner and begin lightly wiping back and forth with broad strokes.

While it’s tempting to rub oily or grimy spots directly, remember that even light rubbing in one spot can cause buff marks. Use the dry portion of your microfiber cloth to remove excess liquid and to dry the TV screen. Let the TV dry completely before you plug it back in and turn it on.

Now that you know how to clean a TV screen, let’s move on to the rest of the package. Wipe down the housing around the screen and the base of the TV with a clean, microfiber cloth dampened with distilled water. Now, turn your TV enough to get access to the back and make sure the TV is stable before you continue cleaning.

Next up, we’re going to clean the air vents and ports. Cleaning these areas is important not only for the sake of cleanliness but also to keep your TV working properly.

The slits or holes on the back of your TV are air vents that keep it from overheating. TV vent cleaning is especially important for plasma TVs that are prone to getting very warm during operation. Your aim is to remove any buildup in your TV’s vents without pushing dirt or dust into its interior. Instead of reaching for a duster or compressed air, use your vacuum’s brush attachment or other extension and vacuum the vents clean.

Ports on a flat screen TV can be on the back, sides, or the top or bottom of the TV casing. We use these ports for HDMI cables, streaming sticks, gaming systems, external speakers, and other electronics. When dirt and dust build up in these openings, it can cause devices connected to them to malfunction.Since these openings are closed off from the inner workings of a TV, you can use compressed air to safely clean them out. Spray at an angle so you don’t push dirt further into the port and don’t put the nozzle into the port because it could damage the connection.

Learning how to clean a TV screen, the housing, vents, and ports will help your flat screen TV perform at its best. If you have remotes, other audio/video devices, and computers that could stand a scrubbing, check out our guide on cleaning and sanitizing electronics. And when you need help cleaning the rest of your home, The Maids offers flexible, affordable cleaning services for your specific cleaning needs. Get your free estimate online and learn more today.

So I"m in the same boat, looking for stuff to clean LCDs. Once in the Apple Store I saw some "Apple Wipes" for cleaning your tre-chic computer. Buying those would make me a massive tool and I figure they"re only for cleaning the glossy parts, not the shiny parts.

I use a cleaner from Kensington (http://www.kensington.com/html/1081.html) on my monitor _and_ my LCDs and it works great. It comes in a little spray bottle, and I use these neat little 3M "electronics" microfiber cloths to buff off the spray. Works like a charm.

I tried those cloths that were already pre-moistened with cleaner (don"t remember the brand name), and they left a ton of streaks...I don"t recommend them.

The official word on LCD cleaning in Apple manuals is to use a solution of diluted isopropyl alcohol, no more than a 50% solution. Usually the rubbing alcohol you buy at a drugstore that is either 90% or 98% pure but 98% is pretty hard to get (you don"t need it anyway). I mix 1 part water and 1 part 90% isopropyl alcohol, which works out to... um.. something just under a 50% solution.

Be absolutely sure to use a very VERY soft cloth. I use a piece of soft flannel. Do NOT use paper towels or anything more abrasive than an old worn out cotton Tshirt. Absolutely do NOT use windex or anything with ammonia in it, it can etch the screen surface and can cause the plastic to go cloudy. You don"t want that to happen!

BTW, there is a commercial cleaning solution called something like Klear-Screen, it"s pretty expensive. It is merely a 50% solution of isopropyl alcohol and water. Just like I make, for a fraction of the cost.

Just read the ingredients list on my bottle of Kensington "Screen Guardian", and it"s the exact recipe that you have...It was $3, so I guess I was just being lazy :)

The 3M cloths are really nice for the wiping part, though, as they are softer than an old t-shirt, and because of their design, if they do happen to pick up some grit, it doesn"t get trapped on the surface, so you"re less likely to scratch that nice screen. You can also throw them in the laundry every once and awhile, and they come out like new.

I"ve been using Klear Screen for a while now and really like it. The disposable packages make it easy to toss a couple in my bag so I have them with me whenever I need them. Each of the packages has a moistened clean pad and a dry polishing cloth.

I do that too; it"s the best. Where I buy them the staff all run around with dish towels on their shoulder; ready to dry glasses after cleaning them.

For my CRT I use dish soap too. For the LCD on my powerbook I use some little LCD cleaning pads i bought at Frys. Except when I can"t find them, then I just use a dish towel and a bit of water. Or no water. But my Powerbook is falling really badly apart anyway. :-)

Dish soap isn"t soap, it"s almost always detergent. I recommend against it. Soap is a pretty safe cleaner for most surfaces, it"s even used in some circumstances for art conservation etc. but I sure wouldn"t put it on an LCD.

BTW, lens cleaner and eyeglass cleaner is the same 50/50 formula I described. And most better CRT monitors have an antiglare optical coating almost identical to the coating on camera lenses and eyeglasses, the antireflective coating will be degraded over time with paper towels and windex, I use the 50/50/flannel solution on my expensive Sony 20" CRT too.

I spend a lot of time cleaning my optics. I had the antiglare optical coating put on my eyeglasses and boy did I regret it, it was much harder to clean without streaks, showed fingerprints more than uncoated lenses, and I felt like my glasses were constantly dirty and blurry. My optician gave me a new cool microfiber polymer cloth that is extremely soft and will lift fingerprints and gunk from eyeglasses without using any liquids, it"s amazing. Might be worth checking out this cloth for CRT and LCD cleaning, it"s only like $3 at your local eyeglass shop.

i use a commercial solution its name is nice"n clean you can get it at wallmart also there is clean safe monitor cleaner another option got it from best buy

i use a commercial solution its name is nice"n clean you can get it at wallmart also there is clean safe monitor cleaner another option got it from best buy

Use Klear Screen. The product has been around a long time, and I used to think it was silly, but then I tried it. It"s amazingly good and worth the cash.

I have portbale dvd player that has a LCD screen that needs cleaning! i am afraid to use anyhting because peopel tell me that certain things ruin the screen. What should I use to clean it?

i just use a damp cloth just enough to get the dust out too, windex and other stuff will kill the lcd"s after a while so i just wipe it most of the time with a dry paper towel straight across or horizontally and that does the trick

i just use a damp cloth just enough to get the dust out too, windex and other stuff will kill the lcd"s after a while so i just wipe it most of the time with a dry paper towel straight across or horizontally and that does the trick

i just use a damp cloth just enough to get the dust out too, windex and other stuff will kill the lcd"s after a while so i just wipe it most of the time with a dry paper towel straight across or horizontally and that does the trick

Great suggestion by Charles on the use of 50/50 alcohol and water. I just used it to clean those fingerprints from my coworkers and water drops/spray.

Great suggestion by Charles on the use of 50/50 alcohol and water. I just used it to clean those fingerprints from my coworkers and water drops/spray. It worked great !

I was not impressed with the results. At first it seemed like the solution didn"t work, but I looked again at the bottle of rubbing alchool and it turns out it was a %70 concentrate, so I added a bit more to the solution and it worked like a charm. A mirco fiber cloth for glasses is what I used.

Everybody seems to accept the 45%-50% isopropyl alcohol solution. So that is what I"ll do. I am sure that later I"ll put another message saying: "It worked like a charm". So there.

Charels...great suggestion....my screen cleans great with that recipie! It won"t make my screen yellow like the other solutions people mentioned though?

First time I"ve made a comment on a blog. Just did a search for "clean LCD screen" and Jeremy"s page came up. I read all the comments with interest (and amusement on some). The chemical mixes etc sounded like too much effort, so I went for the "very, slightly damp cloth" approach. Importantly the cloth is one of those MICRO-FIBRE ones which are marketed as smear free. It worked an absolute treat. It"s a Vileda one. Either my web connection is slow or their site is crap (wanted to post a link) but you should be able to get them from your regular supermarket.

Seemed to me the less chemicals, the better. I read this page, got a soft washcloth from the bathroom, wet it, wrung it out extremely well and simply wiped the screen off. It"s now as clean as the day I bought it. Sold!

I used Walmard no glare lens cleaner that came with my glasses and it works fine. It is a non-alcohol product. I also used the microfiber cloth that came with it in a little package. I didn"t realize how dirty my monitor was.

3. Wipe the LCD or flat panel screen gently with a soft dry cloth. If any marks remain, moisten the cloth with LCD cleaner, and then gently stroke the cloth across the display in one direction, moving from the top of the display to the bottom.

NOTICE: Do not use any of the following chemicals or any solutions that contain them: Acetone, ethyl alcohol, toluene, ethyl acid, ammonia, or methyl chloride. If you have a different chemical or solution and are not sure whether it is suitable, do not use it. Using any of the chemicals in the previous list may cause permanent damage to the LCD or flat panel screen. Some commercial window cleaners contain ammonia and are therefore unacceptable.

There are many cleaning solutions sold specifically as LCD cleaners. You can use these to clean LCD screens on Dell notebooks. Alternately, you may use a 50/50 isopropyl alcohol (IPA) and water mixture. Microfiber cloths such as those used to clean eyeglasses are excellent for use with LCDs.

Related to the topic is how to avoid the marks that the keyboard actually leaves on the screen after a (long) while of utilization. A friend of mine has come up with the idea to place a tiny mouse mat inbetween the screen and the keyboard before closing the notebook. Each time. Takes some practice, but actually works pretty well.

I wipe mine with a piece of steak, medium rare - never overcook it - then take a walk down to the store and make a concoction of chutney and mild antipasto. After watching Dr. Strangelove and enjoying a Monte Cristo #1 with a nice Remy I get a cloth and wipe it all off with pure rainwater (so as to not to sap and impurify my precious bodily fluids.). . . or sometimes I just use alchohol and water with a soft cloth.

Thank you so much to everyone here who posted. I got my husband a brand new LCD monitor for his birthday about a week ago and today our two year old wrote on it with a ball point pen. After calling the company twice I was pretty convinced that the monitor was ruined, but the alchol took almost all the pen off and there are just a couple places that were damaged. Thank you so much.

I didn"t read the Knowledge Base for my Sony Vaio until after using windex on the screen. Now that I have these streaks what can I do? I ask because the sony site specifically says not to use alcohol and Isopropyl is alcohol???

WARNING: There is a risk of hardware damage. Do not scratch or exert pressure on the LCD. Do not use any type of window cleaner, abrasive pad, scouring powder or solvents (such as alcohol or benzine). Do not leave the LCD facing the sun. Doing any of these things could cause the LCD to become damaged or to malfunction.

Thanks guys! I scrawled a wiggly line with a permanent black marker on my lovely new 19" LCD screen (yeah, they breed "em pretty stupid Down Under). But I read your advice about 50/50 isopropyl alcohol/water, shot off to the chemist to get 50 ml of the magic potion and now it"s as good as new. Brilliant!

I"m wondering if any of you could help me. My youngest thought my Hp omnibook XE3"s screen looked dirt and used something with ammonia in it to wipe the screen down while it was running. At the same time it was starting to overheat so I shut it down. When I turned it back on, the screen is black and I can barely seen anything. Is the screen fubared or do I just need to clean it again?

There are many products out there, but some are better than others. iKlear Apple Polish & Monster Screen Clean Kit are tested and proven to work. **Both products DO NOT contain any alcohol or ammonia and have anti-static properties. Their formulas are engineered for LCD screens and their special coatings.

I use Windex. I used to spray the screen and wipe it with a paper towel until I ruined my first display (Windex behind the screen"s bezel). Now, I spray the paper towel and wipe the screen.

The question is: Can the antiglare coating be reapplied either with a commercial product or by the manufacturer or will the monitor need to be replaced.

This is an important issue to me due to an eye problem that makes me susceptable to glare. I cannot use standard monitors without a glare screen or other glare retardant

Now for another great horror story, how about a 3 year old drawing a picture and coloring it on a brand new 19" FP LCD. Yes it happen, then this same child managed to dock a PBNJ sandwich into the DVD player.

Ok, now some people may have a REALLY hard time cleanign their LCD monitors and televisions, but i was born to make it even harder. Now this is so difficult it may cause extremely bad headaches.

First I will tell you what happened to me. My little brother and me were painting a room for my mom, and i took my eyes off him for one second and he went into MY room and had COVERED my entire computer system including tower, LCD, and printer with PINK paint!!!!!!!!! And also let me mention that i had just bought this computer. I wanted to put him through osmosis. So what did i do? I cleaned it. Here"s how to clean an LCD monitor (even with pink paint on it.)

Pink LATEX paint is one thing, but how"s this -- I had my laptop on my clean garage workbench, when an aerosol can of grey oil-based paint rolls off the bench and impales itself on a sharp metal contraption I was working on. It proceeds to spew a fine mist of paint on everything within a 10 foot circle. Now I have a fine mist of grey oil-based paint on my laptop LCD. I can use the laptop, but these little dots are annoying, and NOTHING gets them off.

Working for an isp has its advantages, we all use Windex (our side of the world, Zimbabwe...we call it Windoleen!) We spray on a kitchen cloth and then wipe gently. Being greek of course you can use Windex on just about anything!!!!

I read this page with great amusment (the yello screen, grey paint, todler with the ball point pen and the rest). However the fourth last reply (by John Collier) seamed the logical and that is exactly what i did, looks as new as the day i bought it.

The spots seem to be on the inside of the LCD -- does anyone have any ideas? I don"t know what else to do -- I"ve even tried "elbow grease" with the traditional substances -- but no success with these either.

I just used water on a t-shirt and my screen turned out clean as new, I had a screen cleaner at home but I didn�t want to use it just to see what happens haha.

I use some insanely expensive screen wipes that I got at best buy, they come in a container much like baby wipes. They cost around $10 for I think 50, I treat them like gold and use them maybe twice a month.

I have been using Klear Screen as recommended by Apple for a few years now. It come in a bulk spray bottle or individual packets that you can keep in your laptop bag for cleaning on the go. It works great for CRT as well as LCD screens. For as little as $10 + shipping you can"t go wrong.

Thank you all for your suggestions, even the silly ones. :-) The big thing I got out of it is that ammonia (didn"t know this) and acetone (a no-brainer) would be bad ideas. The 50/50 isopropyl alcohol and water sounds like a good idea, and I"m surprised that some maufacturers discourage it. I"m legally blind, and when I got these glasses (8X telsescope mounted to right lens) in "79, I was given a bottle of Look-Lite and a box of Kimwipes. The Look-Lite contains isopropyl alcohol, but the label didn"t say how much at the time. I"ve used just plain water, mostly, but I think I"ll see about finding a small bottle that will produce a fine mist and mix up the 50/50 solution for the glasses *and* my LCD flat panel and laptop screen.

My mother, God bless her, got me a microfiber cloth by Fellowes for Christmas that I just used to clean the LCD. Looks pretty good, as far as I can tell. B-) While cleaning the TV with it, though, I found some nasty scratches that have apparently been there for a while. I couldn"t see them, so I guess they don"t matter. It"s only a $200 flat-screen Philips, anyway. But, the $600 LCD is a different matter. Again, thanks for the suggestions, All.

thanx 4 the good info , just dropped 450 on a 19 b4 xmas and still havent cleaned it for fear of the horror stories (makes me half wish i got a monster crt lol)

hey...i had the same problem until i came across a high performace cloth my dad had bought for his computer. Its made by 3M technology and it"s super soft. I use it all the time to dust off my screen and buff off any smears or prints on the screen. If something is resisting your cleaning use water.

I just used a mixture of approx. 50 % Isopropyl Alocohol and 50% water (mixed very inprecisely) and used a clean cloth diaper. It worked great! The fingerprints and unidentified smudged disappeared from my laptop screen, the 15" LCD screen with my desktop looks brand new, and the 7" fold down screen in the minivan never looked better. In fact, the 1/4 cup solution that I made was enough to clean the CRT screen on my 36" TV, a bathroom mirror, and a hallway mirror. I may never buy Window cleaner again!

Isopropyl, at least on optics, leave an undesired film... is denatured that difficult to get a hold of? I"m surprised Isopropyl is used at all in lens cleaning. I would only use it on electronics, i.e., solder joints...

My three year old took a good ol" ball point pen to my 19" ViewSonic LCD. I took care of him with a spankin" and the monitor with 70% alcohol. Both worked like a charm.

I have a laptop and would also like to get it clean as whenit was new. Unfortunately, some of the products you recommend are not available where i live (south america).

I read with attention the recomendations about not using alcohol, ammonia, etc. So probably some water and a damp cloth would be enough, unless you need a more serious cleaning. So I would pls, ask you some others home based solutions.

Somehow my LCD managed to get a smear of AstroGlide personal lubricant on it (go figure)... this is proving IMPOSSIBLE to remove... I"ve tried a moistened cotton towel, than some $20 a bottle Monster ScreenClean to no avail. Help?

Clean LCD screen is a more popular search than i expected. The alcohol solution on my old nightshirt worked beautifully. I poured some alcohol through the slot on the floppy drive and it updated my BIOS! Excellent!

I just read the above responses and after ready the remidies you all suggested, I decided to get brave and use my own favorite "get anything out" solution. It is called "Lickity Split" by Kirby home care prducts. It cleaned the LCD screen to look new. I strongly suggest it for anything. (Lipstick, crayon, glue, oil, tar, permanent marker, and more. You should check it out.

I have an Elvis thing going with my laptop. Every time I log into my DMOZ editors dashboard I reach for my gun and threaten the screen. Hard to wipe away a bullet hole.

When I purchase a new LCD the first thing I do is cover it with Saran wrap to prevent any dust. If I am in a dust storm then I store it in a plastic bubble to protect it from debris. Okay. Thanks very much.

The 50% *isopropyl* alcohol (IPA) solution seems to be endorsed by IBM too: http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-4A2P54

If you use an aerosol can to spray a mist over a lighter flame it produces a huge flame. Perfect for burning off dust and smears from lcd screens. If that doesn"t work I usually cut a hole in my car battery and wipe the screen down with battery acid applied to a VERY SOFT cloth, not papertowels or anything like that. It has to be a soft cloth and battery acid. It works

With regard to the posted IBM link by jlmarin: That link seems to imply that only the OUTSIDE of a laptop can be cleaned with an alcohol-based product. In that same paragraph, it reiterates the LCD cleaning cloth should be DRY (capital letters are IBM"s emphasis, not mine). While isopropyl alcohol may make for a good "occasional" cleaner, sites elsewhere mention that long-term use of it can lead to yellowing and stiffening (ie, brittle) of the LCD plastic covering (screen). Personally, I use Klear Screen (ordered directly from their USA on-line store, and no, I"m not affiliated with them). The Klear Screen product is 83% water and 17% proprietary ingredients (the latter including methyl paraben) according to their MSDS.

Oops, should have added that Methyl Paraben (CAS No.: 99-76-3) is an antibacterial, mold inhibitor, preservative. Data from http://bulkpharm.mallinckrodt.com/_attachments/msds/MPARA.htm and other sites.

And looking back over the prior posts, Charles" post of April 2003 suggests that Klean Screen uses alcohol. I"m not sure if they once did, but they not specifically state their product is alcohol and ammonia free. The Apple web page I saw, referred to by another poster here, states that alcohol products should not be used.

Like a few others on this topic, I had my 3 year-old draw a masterpiece on my LCD screen with a ball point pen. In a few places it almost looked like the screen was damaged from the sharpness of the pen. I tried the glasses cleaner from my optometrist, no luck. I tried 50/50 isopropyl alcohol and it made a small dent, but not much. I added more alcohol to the mix and got slightly better results, but the final trick that got that pen off was straight 70% isopropyl alcohol. It all came clean, thank you for the posts! We"ll probably get a small yellow spot from the windex my wife first applied to a corner of the screen to "test" it. We may get an entire yellow screen someday from the straight rubbing alcohol, but at least it bought me a little time.

Ok all you crazy and nutty scardy cats! Soft washcloth with just a touch of water is the best. Forget all that malarky about 50% alcohol. Rock it old school with water and a towel. My screen is as see through as the Bush Administration"s lies ;-)

From a "scardy cat". Water is fine for water-soluble contaminants such as dust and common everyday dirt, however it does nothing for wax/oil-based smudges such as some inks, finger prints, food products, etc. In these cases, another non-water-based solvent needs to be used. Whether one uses alcohol or a commercial product is typically based on experience and word of mouth. The alcohol-based and other very similar products will "eventually" ruin a LCD or optically coated screen. Therefore, my preference is for a commercial non-alcohol, non-ammonia based products (already mentioned here) and the softest towels available.

In case this may help someone else: I was looking for some help cleaning off something sticky (maybe gum??) from an open box item I purchased for a reduced price. It is a Sharp aquos tv - I couldn"t find anything related to this, so since I knew I could return the item if it didn"t work - I used WD-40. It worked like a charm, then used a very mild solution of water and dishsoap (couple of drops) to clean again and walah - no more sticky screen and a TV for quite a reduced price.

I prefer to cover my LCD in tobasco sauce and bake it in the sun. The acids eat the dirt away. Baking it in the sun allows for those acids to soak into the plastic and when the hardened tobasco sauce is chipped off, offers future protection from dirt and grime. Oh yeah, the other thing I do to clean my monitor is to tie a rope to it, bring it in the car with me to the top of our local bridge over the root river. I then toss the monitor over the bridge and yank it up and down in the water a few times. Works like a charm.

First I don"t know how people can stand dirt on the screen. Or how they can keep from getting dirt etc on there but anyway. John Collier knows what he"s talking about. Soft wet (with water) really takes care of everything. And it"s streak free, I"ve tried the cloths and the endust stuff they all leave streaks. I hate streaks. Also I have three children,ages 2-7 and two lovely 19 inch flat screens. My children have never hurt them or the computers. Which are sitting in the living room I would suggest proper supervision for that. Honestly children are not animals they can respect your possesions!

Just thought it was interesting that I stumbled upon this while trying to figure out how to clean my lcd screen on easter sunday, also. Only 2 years later.

I"m looking for some tips. I recently purchased a Compaq Presario R3000. I use it at school and home. I wanted to know what I can buy to clean the outside with (I assume it"s plastic) and what to clean my LCD screen with. I"m looking for a product that is already made...I don"t trust myself with diluting alcohol. And also, I cleaned my touchpad with rubbing alcohol, and it didn"t seem to do much good. I keep the screen down when my computer"s not in use, but it STILL gets dust on it. Is there anything out there that will help prevent dust buildup? (I"m new at cleaning laptops...it"s my first one!)

the non-glare coating will dissolve after a while using any type of alcohol solution. either dont use or use and live without antiglare. there are antiglare screen covers that can be used or use polarizing soft films(gels).

I have an LCD TV in my kitchin, the place you would expect a screen to pick up grease - nasty. So guess what . . . I never clean the screen . . . and How can that be? . . . Well you don"t have to if you replace the cling-film often enough.

Something that may be helpful if anyone has lazy pizels on their lcd"s ie. the pixel remains one colour. (not for dead pixels) If you run some fast graphics it something with alot of colour changes quickly and GENTLY massage the display in a circular motion (note use a lint free cleaning cloth to do this) it may revive. Now I must be 100% sure you have the GENTLE bit. This will not work on all lazy pixels and definatly not on dead ones but is definatly worth a try.

I have found that toilet roll and a small quantity of Bacardi works wonders. In terms of convenience, I"m sure there are far more of us with Bacardi in store that a isopropyl alcohol solution!

I always an industrial floor buffer to clean my laptop screen. Open out your laptop screen to the max(180 degrees), lie it face up on a hard gravel surface...perhaps on your driveway and away you go!!!

I use a pair of my underwear and some Finlandia vodka. Or at least that"s what I assumed waking up with an empty bottle and my underwear in my hand, with my head on the keyboard. I must have been cleaning SOMETHING, although my LCD screen has a few white spots. (dead pixels?) I can still make out the impression of the keys on my forehead, and my girlfriend wont shut up about the email that I sent her that was full of the letter "h".

i use a wet handerchief, but i"m going to use Endust for Electronics next time i clean it. i wasn"t so trusting of it, even though it says on it "Use On: (bunch of stuff), non-glare and laptop computer screens", but i just looked at the ingredients online and it looks to be good (and i know a little chemistry if you"re worried i missed something)

Every time I clean my screen,I usually use the same process they used on Linda Blair In the movie the Exorcist....I Bring In two catholic priests,both with bottles of the 50/50 solution.

We have an LCD tv and my son got crayon on it, i"m so nervous to use anything on it and i"m looking for something to dissolve it so it will wipe off??? Any suggestions?

We have an LCD tv and my son got crayon on it, i"m so nervous to use anything on it and i"m looking for something to dissolve it so it will wipe off??? Any suggestions?

I can"t believe it. Some folks actually researched and took the time to document that: Yes, acohol and water (1:1) will clean a screen, but it WILL disolve anti-glare coatings, make LCD screens turn very yellow and hard with continued use, leave a white film if allowed to dry, disolve lubricating components if it seeps down into the hinges of a laptop. For CASUAL or ONE-TIME use only, the alcohol:water treatment is probably okay, but NOT FOR LONG-TERM/MULTIPLE use. Absolutely, under no circumstances, should company employ this technique in their normal practice.

It"s surprising how many people use the alcohol or ammonia based cleans once, have a good result, and tell all their friens about it. Wrong, wrong, wrong.

*QUITE A FEW apparently since alchohol is NOT good, as noted previously: Yes, alcohol and water (1:1) will clean a screen, but it WILL disolve anti-glare coatings, make LCD screens turn