sealed lcd module supplier

Distributor of component LCDs for equipment which provide high-contrast ratio, color saturation, luminance and performance enhancements such as advanced wide viewing (AWV) for true color fidelity, super-high brightness (SHB) and wide temperature range. Focus on industrial, instrumentation, hand-helds, medical and other low-to-medium volume markets. High-bright LED backlights for outdoor use. LVDS interfaces decrease EMI. Factory installed touch screen solutions. 3.5" to 12.1" QVGA, HVGA, VGA, WVGA, SVGA, XGA, WXGA. Also distributes other related products including LED drivers, lamps, indicators, LED assemblies, segment displays, LED mounts, LEDs, and light pipes. Distributor of electronic components, hardware and fasteners and provides design/value engineering support, fulfillment strategies, procurement services and transactional models to meet specific needs and priorities.

Crystalfontz America is the leading supplier of LCD, TFT, OLED and ePaper display modules and accessories. We specialize in providing our customers the very best in display products, cables and connectors.

In addition to our large catalog of displays, we offer LCD development kits, breakout boards, cables, ZIF connectors and all of the LCD software and drivers you need to develop your product or project. We are located in the U.S. so we can get product to you fast!

Edge Electronics is a leading authorized distributor of top name brand LCD products. We deal directly with factories that build LCDs and a broad range of related products including backlights, graphic displays, LCD cables and panels, inverter and controller boards, panels, touch screens, and more. We also offer complete LCD kit solutions to fit your design.

We use our LCD complementing lines to suggest the most compatible products to meet your needs. If you have a display picked out, we can suggest the appropriate LCD controller board, cables, touch screen, or other related parts your project requires. Custom products require custom attention, which is why we offer engineering support for all of our display products.

Our LCD Quick Kits are ready-to-go, plug-and-play display units - perfect to get a jump start while designing new products. These kits and associated components are usually in stock and available for you to order immediately. Visit our LCD Quick Kit Page to choose the right solution for your project. Please note, we can supply products individually, in kits, with enhancements, or integrated with other display products.

If what you need is not listed, we can develop a kit with any display you are interested in (depending on the components, there could be lead time associate with creating a custom LCD kit). Fortunately, being a small business, we are fast and flexible, allowing for a solid supply chain of service. Browse our LCD Product Selector Page to learn more about the available options.

Receive a free consultation to learn more about our indoor and outdoor industrial LCD monitor computer productsand touch screensand other accessories.

Choose a product category from our diverse selection of industrial LCD products. To help you decide which category best suits your LCD monitor needs, mouse over the images for a popup description of each product family.

iTechLCD founded in 2004 is a worldwide company with the objective of designing, developing, and manufacturing complete all weather proof outdoor/semi outdoor high brightness, sunlight readable, full HD LCD with sealed IP65/NEMA4 enclosures. We have references all around the globe with almost hundreds of screens installed in harsh coldest and hottest outdoor environment from Las Vegas, USA to Montreal/Quebec, Canada. Our outdoor screens providing the real world proofing of reliability for many years to come.

TOPWAY HMT070ETA-C is a Smart TFT Module with 32bit MCU on board. Its graphics engine provides numbers of out standing features. Itsupports TOPWAY TML 3.0 for preload and predesign display interface that simplify the host operation and ...

TOPWAY HKT070DTA-3C is a Smart TFT Module with 32bit MCU on board. Its graphics engine provides numbers of out standing features. Itsupports TOPWAY TML 3.0 for preload and predesign display interface that simplify the host operation and ...

This 7 inch TFT LCD display is made by TianMa,it suit for industry control, instrumentatiom,medical electronics, power electric equipment applications.

REA128128G is a dot matrix 128x128 COG graphic type OLED module. The size of the active area is 1,12”diagonal with module dimension 26.4×38.6 mm. This OLED module has built-in IC SH1107 supporting 4-wire SPI interface. The additional ...

REA009616B is a dot matrix 96x16 COG graphic type OLED module. The size of the active area is 0.69”diagonal with module dimension 33×10 mm. This OLED module has built-in IC SSD1306 supporting I2C interface. The additional PCB on this ...

REX012832N is a dot matrix 128x32 COG graphic type OLED display module. The size of the active area is 2.23” diagonal with module dimension 62×24 mm. This OLED module has built-in IC SH1106 supporting 6800, 8080, 4-Wire SPI interface ...

Display graphics, text, or video with HED’s range of color graphical display modules. Rugged, sunlight readable and sealed to IP67, HED displays can be mounted in the cab or outside your vehicle. Do-It-Yourself programming and diagnostic software tools allows users to easily and quickly develop screens to show all the critical system parameters using gauges, bar graphs, text and other graphical methods for easy user interpretation. These features allow for gauges and camera monitors to be consolidated all onto one display.

To resize a LCD is literally to cut the glass, polarizers, circuits and circuit boards to a new size. Years ago, it was thought impossible to preserve the original performance of a previously manufactured LCD once the glass circuits are cut. However, Litemax has done the impossible, over and over again, becoming the world"s leading pioneer and leader in LCD resizing solutions.

Squarepixel series is designed for high brightness with power efficiency LED backlight. It provides LCD panel with specific aspect ratios and sunlight readable for digital signage, public transportation, exhibition hall, department store, and the vending machines.

The spirit of Durapixel indeed lies with its name: durability. Why Durapixel? Commercial-grade LCD displays, due to the competitive pricing structure, are unable to offer more than MTBF of 30,000 hours, which will not be sufficient for any applications that require around-the-clock operations. System designers, integrators and users serious about rugged, industrial displays for demanding environments need to look no further – the unfailingly robust and high-quality Durapixel is the key to each of your success.

UbiPixel, industrial LCDs are used in many professional applications. High bright sunlight readable and low power consumption display technologies offer the highest quality LCDs for specific industrial applications. Our embedded LCD can be manufactured in an open frame, VESA mount, or fully enclosed housing for HMI display, KIOSK, Vending machine, home automation, point-of-sale terminals, digital signage and more. UbiPixel, industrial LCDs are used in many professional applications. High bright sunlight readable and low power consumption display technologies offer the highest quality LCD screen for specific industrial applications. Our embedded LCD can be manufactured in an open frame, VESA mount or fully enclosed housing for HMI display, KIOSK, Vending machine, home automation, point-of-sale terminals, digital signage and more.

Litemax"s 3.5" SBCs feature rich I/O ports, wide-temperature support, and wide input voltage range and low-power to robust high -performance computing modules designed for outdoor applications or harsh environmental requirements.

Featuring a modular designed, this series can be fitted with a number of modules to expand its base capabilities. On-site maintenance and future upgradability are easier than ever by deploying our panel PCs and monitors.

The Litemax ITRP series is fanless Passenger Information System, It features stretched LCD display, with high brightness to ensure easy readability even in light-insufficient environments. It serves as a reliable platform to provide passenger information on wide versatility of vehicles, such as bus and trams.

Intel® offers the Intel® Smart Display Module (Intel® SDM) specification and reference design that can be integrated into the sleekest all-in-one designs. Intel® SDM delivers the same level of intelligence and interoperability as the Open Pluggable Specification, but in our smallest form factor yet eliminates the housing and advances the thinnest integrated displays.

The new Intel® Smart Kiosk Module (Intel® SKM) is a revolutionary solution that makes it easier to scale and maintain interactive kiosks, which are increasingly being used by businesses and governments worldwide to offer customers around-the-clock access to information and services.As the market for interactive kiosks increases, so does the demand for smarter multi-function kiosks with advanced capabilities such as workload consolidation, artificial intelligence, smartphone and social media integration, 5G connectivity, telepresence, remote manageability, and data analytics.

LCD dust seals and touch screen dust seals are the most basic requirement of display gasketing. These are often static (not portable), indoor applications where the device is not to be exposed to water. Sealing can be achieved by closed cell sponge materials or fine pore open cell materials such as PORON urethane foam.

Light leaking is sometimes a concern with certain LCD or LED display applications. This can be addressed with black gasketing with either a very thin adhesive or a black supported adhesive. A common material configuration for this is soft PORON urethane foam with 3M 9795B adhesive. The 3M 9795B is a film supported double coat adhesive with a black PET support layer that does not pipe light.

It is important to keep in mind the clamping loads. While wider gasket walls generally seal better, the overall surface area is directly related to the loads applied to the LCD and touchscreen. Compression Force Deflection curves of various materials are available to aid designers.

A liquid crystal display structure in which switching transistors or diodes are attached to each pixel to control the on/off voltage. It produces a brighter and sharper display with a broader viewing angle than a passive matrix display. Also known as AMLCD (active matrix liquid crystal display). See TFT (thin film transistor).

This is often described as a matte coating as it is non-reflective to the user since it diffuses rather than reflects ambient light. It provides a method for manufacturers to avoid glare on the viewing surface from other light sources and has been used in the LCD monitor market for many years since the first TFT displays started to emerge. The matte coating is included as an outer polarizing later which has been coarsened by mechanical or chemical processes. This achieves a surface coating which is not smooth and so can diffuse ambient light rather than reflect it.

An adhesive is applied between the display and touch panel using the inactive area around the perimeter of the module. This bonding method results in some inactive space ‘air gap’ between the touch panel substrate and the display. This is the most cost-effective and common solution.

A backlight is used behind the LCD glass to allow the LCM to be read in dark conditions. The vast majority of backlights are now LED. Historically there were also EL (electroluminescent) and CCFL (Cold Cathode Fluorescent Light) backlights, but as LED efficiency has increased and cost has decreased, EL and CCFL backlights have all but disappeared.

A frame of plastic or metal, fitting over the LCD glass, to protect the edges of the glass and actas a pressure device, compressing the elastomer connector between the PCB and LCD glass.

Normally an LCD’s backlight is set to the brightness that will make a white pixel fully illuminated. CABC automatically dims the backlight to the lowest level required for the brightest pixel on the display.

Character LCDs include a fixed CGROM to define the bulk of the characters they display. However, since the CGROM cannot be changed the designers also included the CGRAM — a small number of characters (typically 8) that can be redefined at run-time. These eight characters are usually mapped to characters 0DEC (0x00HEX) to 7DEC (0x07HEX). The CGRAM definitions can be used to make small animations, bar graphs, and similar small graphic or sprite images. This term very likely has its beginning in the granddaddy of all LCD controllers, the venerable Hitachi HD44780.

The CGROM stores the font that is displayed on a character LCD. When you tell a character LCD to display the letter ‘A’, it needs to know which dots to turn on so that we see an ‘A’. This information is stored in the CGROM. By definition, (since it is a ROM) the font that is stored in the CGROM cannot be changed. Be sure to check the datasheet of the character LCD module to make sure that it can display the characters you need. Typically, a CGROM for a character display module has 240 characters defined. The lower half of the CGROM maps to the normal ASCII characters. Since the early character display controllers were designed in Japan, many CGROM have Japanese characters in the upper 128 positions. There are also some CGROMs that have European or Cyrillic characters in these upper locations.

The WS0010 is a more modern character OLED controller, and the designers have included several CGROMs that can be chosen at run-time, so there is not the need to lock in a particular character set at design time. Since the CGROM is completely determined at the time of manufacture of the LCD controller, the designers also included a CGRAM, which allows the bitmaps of a few characters to be redefined at run-time. This term very likely has its beginning in the granddaddy of all LCD controllers, the venerable Hitachi HD44780).

The Display Data RAM holds the letters that get shown on the LCD of a character LCD module. For instance, the letter ‘A’ is stored in its ASCII equivalent 65DEC (0x41HEX) in the DDRAM.

So a 20×2 character LCD would have enough DDRAM to store 40 letters. The value in the DDRAM is used to find the correct bitmap in the CGROM (Character Generator ROM) or CGRAM (Character Generator RAM), it is this small bitmap that gets displayed on the LCD. This term very likely has its beginning in the granddaddy of all LCD controllers, the venerable Hitachi HD44780.

Translucent material used for light diffusion placed between backlight lighting sources and the back side of an LCD. This material will create a more uniform backlight for an LCD from several unique sources of light.

Refers to a graphic controller from Bridgetek/FTDI. EVE graphic controllers are easy to use and can control the display, touch, backlight, and audio features of an embedded system, with each appearing to the host MCU as a memory-mapped SPI device. The host MCU sends commands and data using SPI protocol. EVE modules accept high level commands, simplify writing images and fonts (included angled fonts) on TFTs. Fonts, buttons, and tables can each be easily sent to a TFT using a one-line command.

A silicone rubber strip made up of sequentially spaced conductive and non-conductive material. A thin conductive material used to make connections between an LCD and a PC board.

A dead short is created when excess DC voltage is applied to an LCD. Conductive particles from one piece of glass are transferred through the liquid crystal fluid and deposited on the conductive surface of the opposite piece of glass.

The space left between the epoxy seals on one end of the LCD glass after assembly. This space,used to fill the glass with the liquid crystal fluid, is noted by a mound of epoxy.

An LCD construction technique where the cell geometry is optimized for maximum contrast and viewing angle. The geometry is different for each LCD fluid.

Typically, both the master and slave are implemented in hardware. The I2C master can be implemented in software quite easily, but it can be rather difficult to meet the timing requirements of I2C in a software slave implementation. As micro controllers continue to get faster, writing an I2C software slave will become easier. The I2C standard is pretty well defined, so there is not a huge amount of variation in I2C as it is implemented on LCD, capacitive touch and OLED controllers.

An LCD is composed of two pieces of glass with a thin layer of liquid crystals between the glass layers. When a voltage is applied to the glass, the orientation of the crystals can be changed. This change in the crystal’s orientation (called polarization) will make either a dark or a light area, creating a character or image on the display.

A twisted nematic LCD design where the backlight is blocked when pixels are in the unselected state. Therefore, when no voltage is applied, the screen is black.

A twisted nematic LCD design where light is transmitted when pixels are in the unselected state. Therefore, when no voltage is applied, the screen is white.

Optical bonding improves the optical performance of the display. It eliminates the air gap between the cover glass and the LCD, and usually includes an anti-reflective (A/R) coating (as well as anti-smudge and anti-glare treatments on the cover glass). Optical bonding improves the contrast ratio by reducing the amount of reflected light, thus improving the viewability of the LCD screen. This is especially important in outdoor.

Besides the optical advantages, bonding a sheet of glass to the LCD also improves the durability of the display. It can resist scratches, condensation, and has an improved range of operating temperatures. As touchscreen devices become ubiquitous in consumer markets, this increased ruggedness becomes even more important. Also, by reducing the light loss due to reflection, the battery life of the device can be extended as the device does not need as much backlight to power the display.

On-Cell Touch (OCT) technology permits the Projected Capacitive (PCAP) touch sensor layer to be built into the LCD structure. With this integrated structure, the touch functionality is embedded within the display itself rather than a separate touch screen component on top of the display. The reduction in the number of layers also reduces parallax errors providing a superior touch interface. Fewer layers also means backlight intensity can be reduced while providing the same brightness level. The usual multitouch display has an 88% transparency while an OCT display is 93%. This helps reduce lighting power requirements and extends battery life.

For optical bonding optically clear adhesive is applied over the entire surface between the display assembly and touch panel. This bonding method removes all air and air bubbles from the viewing area providing a more rugged and optically attractive solution. Removal of ‘air gap’ between the module and touch panel eliminates surface-to-surface reflections which degrade contrast and ultimately viewing angles, especially significant in sunlight conditions.

A technique where the alignment layer (Polyimide) on the LCD substrate is rubbed in one or more directions. This process aligns the liquid crystal molecules parallel to the buffing direction.

SPI is a simple serial bus that is often used by LCD or OLED controllers. SPI as implemented for OLED and LCD controllers typically uses a “3-wire SPI” or “4-wire SPI” scheme. SPI was originally championed by Motorola (now Freescale). In its original “pure” form SPI uses four signals:

TFTs are also known as “Active Matrix TFT LCD modules” and have an array of these thin film transistors fabricated on the glass that makes the LCD. By using this active transistor-per-pixel architecture, the contrast of each pixel is good, allowing bright full-color, full motion images to be displayed.

VA is also called VTN, PMVA, GDV, etc. it is a type of LCD in which the liquid crystals naturally align vertically to the glass substrates. When no voltage is applied, the liquid crystals remain perpendicular to the substrate, creating a black display between crossed polarizers. When voltage is applied, the liquid crystals shift to a tilted position, allowing light to pass through and create a gray-scale display depending on the amount of tilt generated by the electric field. VA displays have a deeper-black background, a higher contrast ratio, a wider viewing angle, and better image quality at extreme temperatures over traditional twisted-nematic displays.

Select coming from a wide array of choices in our 19" Rack Mount Computer Series. Winmate offers both circuit board and also passive backplane rack place pcs created making use of 1U, 2U, 3U as well as 4U elevation rackmount instances. Our company is actually a full-service industrial pc provider. Our industrial computers are filled along with the market"s very most trusted component suppliers such as Intel, Sony, Seagate, etc. Each shelf place personal computer lugs a total 1-year manufacturer"s warranty. To simplify making the perfect rackmount personal computer for the project, give us a call as well as allow our company to quote a personalized shelf mount personal computer for you. Winmate"s Rear Mount Display series is fully enclosed and fixed from the rear. With different touchscreen options, such as resistive touch and protective glass, the LCD displays are suitable for applications like control centers, self-service kiosks, and ATMs.

Winmate’s Rack Mount touch screen is the perfect solution for data centers and server rooms that require touchscreen capabilities. The rack-mount design makes it easy to place flat-screen monitors onto server racks, console drawers, and cabinets for control room and security monitoring applications. Explore a full lineup of rack displays with LCD touchscreens today.

The Digital Signage Bar Type Display is uniquely designed with an ultra-wide LCD panel. Combining a high resolution and a high contrast ratio, these ultramodern displays are here to replace traditional LED signages. Depending on the type of application, Digital Signage Bar Type Display can be installed vertically or horizontally to suit any commercial or industrial environment.

Winmate"s LCD high brightness kit is designed for industrial environments. The LCD Scaler Board come in various industrial-grade displays to suit both industrial and commercial applications, plus they work with all embedded systems.

The display module value chain is very complex with many players. Boyd helps to simplify this for you, delivering differentiated performance at optimal total cost.

Many OEMs rely on Display Integrators to design and deliver custom display modules that meet their needs. These integrators are experts in display module design and assembly, delivering on-specification subassemblies to OEMs for integration into their final product. Boyd has 15+ year relationships with the world’s leading display integrators. We continue to establish new strategic relationships with new market entrants as our customers evolve their preferred display integrator partners.

CDS’s waterproof IP66 Monitor solutions, IP rated monitor, marine displays, touch screen monitor uk, Waterproof IP66 Display solutions, IP rated water proof monitors, and IP66 all weather video monitors are designed completely sealed to meet IP66 standards and specifications (IP67/NEMA 6 and MIL-STD/MIL-SPC upon request ). Engineered and tested to operate in extreme harsh environments, these units are waterproof, shock & vibration resistant, and can be equipped with wide operational temperature components (extended operational temperatures available). The powder-coat aluminium construction provides excellent corrosion resistance and protection from the elements. VESA or RAM mounting holes gives you rugged and versatile mobile mounting options.

The waterproof IP66 Monitor solutions can be Panel Mount Monitors, stainless steel monitors, high brightness monitors, rugged touch display, ip69k monitor, and Industrial Touch Screens or those with other mounting solutions. CDS has lower cost solutions for many manufacturers or distributors of marine displays including bluestone co uk,displaytechnology co uk, orbarco military displays. The rugged touch display range includingip69k monitors,weather proof monitors,rugged industrial lcd monitors, andmilitary grade monitor.

The rugged computer displays and marine computer monitors as well asmilitary LCD displays are various versions ofrugged monitors andpanel pc uk and CDS has now become one of the significantindustrial screens manufacturers in the market expanding its range towaterproof computer monitors andmilitary grade LCD displays, but alsowaterproof LCDs