3.2 inch tft lcd shield touch screen brands

※ Price Increase NotificationThe TFT glass cell makers such as Tianma,Hanstar,BOE,Innolux has reduced or stopped the production of small and medium-sized tft glass cell from August-2020 due to the low profit and focus on the size of LCD TV,Tablet PC and Smart Phone .It results the glass cell price in the market is extremely high,and the same situation happens in IC industry.We deeply regret that rapidly rising costs for glass cell and controller IC necessitate our raising the price of tft display.We have made every attempt to avoid the increase, we could accept no profit from the beginning,but the price is going up frequently ,we"re now losing a lot of money. We have no choice if we want to survive. There is no certain answer for when the price would go back to the normal.We guess it will take at least 6 months until these glass cell and semiconductor manufacturing companies recover the production schedule. (Mar-03-2021)

ER-TFT032-2 is 240x320 dots 3.2 " color tft lcd module display with ILI9320 controller and optional 4-wire resistive touch panel,superior display quality,super wide viewing angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO ARM and Raspberry PI.It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.It supports 8080 16-bit parallel interface. .FPC is soldering type,there is no need for zif connector.Lanscape mode is also available.

Fully assembled 3.2inch display with 320x240 pixels TFT LCD and a resistive touch overlay. Just plug it on top of ODROID-C1. 2x13 tall female header is already soldered on the PCB.

The 3.2 inch TFT LCD module is a special design for Raspberry Pi for portable application. It features a 3.2�display with 320x240 16bit color pixels and resistive touch screen. The LCD is well mated with Pi board and interface with Pi via the high speed SPI port, and support console, X windows, displaying images or video etc. It also provides 4 press buttons for user defined functions.

Fully assembled 3.2 inch 320x240 display with resistive touch overlay.  Simply plug it into the SBC"s 26-pin or 40-pin header.  Leaves 14 pins unused on 40-pin header.  2x13 female header already soldered onto the PCB.

GPU/VPU hardware acceleration requiring OpenGL-ES and video playback are not supported - To playback video on this screen, the file has to be transcoded to 320x240 with FFMPEG software decoding.

If you haven"t runapt-get dist-upgraderecently, go make yourself a cup of tea because it takes a little while update your entire OS.Once the C1 reboots after the installation process, your C1"s touchscreen will automatically be activated and will boot into the desktop.

Put the screen(3.2 inch screen schematic) into shield (TFT01-3.2 shield schematic) first, then connect the shield to Arduino, it is quite straight forward.

3)Download and install UTFT ,URTouch ,SdFat,UTFT_Buttons and UTFT_SdRaw library file from following link and copy them into Arduino library folder. ( i.e. D:\arduino ide\Arduino 1.6.9\libraries )

Download the test program (http://www.kookye.com/download/3.2inchscreen/3.2inchtouchscreentest.zip), upzip and open it,then choose the correct board and port.

You will see the code in each sketch: UTFT myGLCD(CTE32_R2, 38, 39, 40, 41).The first value of code refer to the mode of LCD screen. Please write CTE32_R2 or ILI9341_16 if you LCD screen is ILI9341; Please write CTE32 if you LCD screen is SSD1289;

When you use the others LCD screen from the others seller, you could check the PDF instruction in documentation file or open the UTFT.h file to find the correct code.The controller mode could be identifitied by the back mark as the following pictures.

Note: In the project of testing the SD card，please insert the SD card into the slot in back of the 3.2’’ LCD screen. The format of files in SD card must be the FAT32, you need to put the test files(i.e. ICONS.RAW,WAIT4GPS.RAW,SK45) into the SD card root directory.

Fully assembled 3.2 inch TFT LCD display with 320x240 pixels and a resistive touch overlay. Just plug it on top of the ODROID-C4 / N2 / N2+ / C1 / C1+ / C0.

You will need an official Ubuntu image to configure it. You can simply download the Kernel updates and configure your ODROID-C4 / N2+ / N2 / C1 / C1+ / C0 for this display shield.

Limitation: GPU/VPU Hardware acceleration required for OpenGL-ES and Video playback are not supported. To playback a video on this screen, you need a trans-coded 320×240 video file with FFMPEG software decoding.