arduino 3.5 tft display ili9481 factory

Displays are one of the best ways to provide feedback to users of a particular device or project and often the bigger the display, the better. For today’s tutorial, we will look on how to use the relatively big, low cost, ILI9481 based, 3.5″ Color TFT display with Arduino.

This 3.5″ color TFT display as mentioned above, is based on the ILI9481 TFT display driver. The module offers a resolution of 480×320 pixels and comes with an SD card slot through which an SD card loaded with graphics and UI can be attached to the display. The module is also pre-soldered with pins for easy mount (like a shield) on either of the Arduino Mega and Uno, which is nice since there are not many big TFT displays that work with the Arduino Uno.

The module is compatible with either of the Arduino Uno or the Arduino Mega, so feel free to choose between them or test with both. As usual, these components can be bought via the links attached to them.

One of the good things about this module is the ease with which it can be connected to either of the Arduino Mega or Uno. For this tutorial, we will use the Arduino Uno, since the module comes as a shield with pins soldered to match the Uno’s pinout. All we need to do is snap it onto the top of the Arduino Uno as shown in the image below, thus no wiring required.

This ease of using the module mentioned above is, however, one of the few downsides of the display. If we do not use the attached SD card slot, we will be left with 6 digital and one analog pin as the module use the majority of the Arduino pins. When we use the SD card part of the display, we will be left with just 2 digital and one analog pin which at times limits the kind of project in which we can use this display. This is one of the reasons while the compatibility of this display with the Arduino Mega is such a good news, as the “Mega” offers more digital and analog pins to work with, so when you need extra pins, and size is not an issue, use the Mega.

To easily write code to use this display, we will use the GFX and TFT LCD libraries from “Adafruit” which can be downloaded here. With the library installed we can easily navigate through the examples that come with it and upload them to our setup to see the display in action. By studying these examples, one could easily learn how to use this display. However, I have compiled some of the most important functions for the display of text and graphics into an Arduino sketch for the sake of this tutorial. The complete sketch is attached in a zip file under the download section of this tutorial.

As usual, we will do a quick run through of the code and we start by including the libraries which we will use for the project, in this case, the Adafruit GFX and TFT LCD libraries.

With this done, the Void Setup() function is next. We start the function by issuing atft.reset() command to reset the LCD to default configurations. Next, we specify the type of the LCD we are using via the LCD.begin function and set the rotation of the TFT as desired. We proceed to fill the screen with different colors and display different kind of text using diverse color (via the tft.SetTextColor() function) and font size (via the tft.setTextSize() function).

Next is the void loop() function. Here we basically create a UI to display the youtube subscribe button, using some of the same functions we used under the void setup() function.

The Adafruit library helps reduce the amount of work one needs to do while developing the code for this display, leaving the quality of the user interface to the limitations of the creativity and imagination of the person writing the code.

I just reloaded/reran the "Bodmer_UTFT_Demo_480x320" sketch - I had to rotate the due/tft 180degrees but text is printing correctly so clearly I"m having one of those moments...

With the screen orientated correctly for the demo sketch above my bitmaps are loading upside down! (they were right way up on a ILI9486 display which is what has thrown me). I can rotate those and reload but i"ll then need to also either invert the calculation of Y axis values (GFX has 0,0 in the top left corner, normal convention is bottom left).

This 3.5 inch TFT LCD is based on the ILI9481 LCD driver and gives a very sharp/nice picture quality and works amazing well with Arduino Uno and Arduino Mega Microcontrollers. Unfortunately this display is not a touchscreen display, however it makes it up with the included MicroSD Card Slot. No soldering, no wiring, no fuss just plug and play!

Hey guys, its Nick again, welcome once again to educ8s.tv a channel that is all about DIY electronics projects with Arduino, Raspberry Pi, ESP8266 and other popular boards. Today we are going to look at how to drive the low cost, big, Arduino 3.5″ Color TFT display. At the end of this tutorial, we would have learned how to use this interesting display with the Arduino Uno and Mega boards.

The display is quite big and offers a resolution of 480×320 pixels. It is based on the ILI9481 TFT driver, comes with an SD card slot at the back and it is pre-soldered with pins for easy mount on the Arduino Uno, which is nice since there are not many big TFT displays that work with the Arduino Uno.

Few weeks ago, I discovered this Arduino 3.5″ Color TFT display on Banggood.com and thought it will be useful in some of our projects because of its size and its low price. The price of the display is very low for such a big display, it costs 10$ and banggood.com were kind enough to send me a sample unit in order to test it and share my opinion about it with you.

As shown in the video, we will be performing simple tasks with the display to demonstrate how it works and how you can integrate it in your project. I will be performing demos such as showing how Images stored on an SD card and inserted into the SD slot of the display can be shown on the display.

Connecting the module to the Arduino is very easy. Since the module comes in a shield form, all we need to do is to snap it onto the top of the Arduino Uno as shown in the image below.

One of the few downsides to this display is the amount of the Arduino pins it uses. If we don’t use the SD card slot, we will be left with 6 digitals pins and one analog pin which can be connected to other modules or sensors. but when we use the SD card module part of the display, we will be left with just 2 digital and one analog pin which at times limits what we the kind of project for which we can use this display but fortunately, this display is also compatible with the Arduino Mega board which offers many more digital pins to work with, so when you need extra pins, and size is not an issue, use the mega. Unfortunately, this display does not work with some other Arduino Uno form factor based boards like the Arduino Due or the Wemos D1 ESP8266 board due to pin compatibility and library Issues. The Wemos D1, in particular, has just one analog pin and the display requires 5.

To use this display, we will need the libraries which can found on the product page on banggood.com. All we have to do is to install the library and load any of the examples that are designed for this shield. Since the display uses the familiar Adafruit libraries, we can easily build several impressive projects. I have developed a simple program just to demonstrate how easy it is to use the display thanks to the Adafruit libraries! It uses some of the basic functions in order to display text and simple graphics. You can download the code of this simple example for the Arduino 3.5″ Color TFT display by clicking on the download link below or by clicking on the link in the description of the video.

With this done, we then write the void setup() function. To begin we clear the LCD of previous settings, then set the type LCD we are using via the LCD.begin function. With this done, we set the rotation of the TFT and proceed to fill the screen with different colors.

The void loop section basically echoes some of the things we tried under the void setup function. The idea behind all of this is to show you what is possible with this wonderful display.

The ILI9481 is a driver IC for 480×320 (HVGA) TFT panels. These panels are typically found in mobile phones (for example the iPhone 3G although the display in that phone probably does not have a controller) and other portable devices. HVGA panels contain double the number of pixels of the common 320×240 (QVGA) panels.

I could have tried to track down a connector for the 37-pin, 0.5mm FPC connector but decided against it and just soldered the FPC directly to the adaptor board that the e-bay seller included with the display.

The datasheet also included a schematic for the backlight. Since this is a relatively large 3.5″ panel it has a total of 6 white LEDs connected in parallel to act as a backlight.

My demo sequence exercises some of the common functions used in graphics operations such as rectangle, line and ellipse drawing as well as text rendering and hardware scrolling when the panel supports it (the ILI9481 does).

The datasheet for the ILI9481 is readily available on the internet. It’s written to the high standard that I’ve come to expect from ILITek making the job of writing a driver really straightforward.

Firstly we need to include the headers that define the classes we’re going to use. Secondly, since all of stm32plus lives either in the stm32plus namespace or a sub-namespace (in this case stm32plus::display) we will import them into the global namespace to make the declarations of the objects less clumsy looking.

Our example initialises it in landscape mode, 16 bit colour (64K). If you take a look at TftInterfaces.h you will see that following modes are available:

Setting up the tweaks to the gamma curve are optional, a reasonable display will be obtained by using the default linear curve but if true-to-life colours are a requirement then a custom gamma curve is essential.

I’ve uploaded a pair of short, out of focus and badly produced video that you can waste some of your valuable time by watching if you want to see the ILI9481 panel in action.

ER-TFT035-6 is 320x480 dots 3.5" color tft lcd module display with ILI9488 controller,superior display quality,super wide viewing angle.As a bonus, this display has a optional resistive touch panel and a optional capacitive touch panel with controller FT6236, so you can detect finger presses anywhere on the screen and doesn"t require pressing down on the screen with a stylus and has nice glossy glass cover and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO ARM and Raspberry PI.It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.It supports 8080 8-bit,9-bit,16-bit, parallel,3-wire,4-wire serial spi interface. FPC with zif connector is easily to assemble or remove.Lanscape mode is also available.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!".Here is the link for 3.5"TFT Touch Shield with Libraries, Examples.Schematic Diagram for Arduino Due,Mega 2560 and Uno . For 8051 microcontroller user,we prepared the detailed tutorial such as interfacing, demo code and development kit at the bottom of this page.