how to test laptop lcd display price

When buying a laptop for business work, it is always important to test the system"s hardware so you won"t experience the inconvenience of returning the system for replacement or repairs later on when work gets hectic. The salesperson may simply switch on the laptop and show that it properly boots into Windows as proof that it works so you can finally take it back to the office. However, you need to perform additional steps to test other parts of the laptop such as the screen. Testing the laptop screen early is recommended so you can immediately ask for a replacement if you discover a problem.

To learn more about best practices on handling and using a Dell laptop, see the Dell knowledge base article Best Practices for Product Use and Handling for Dell Laptops.

For displays with glossy bezels, consider the placement of the display as the bezel may cause disturbing reflections from surrounding light and bright surfaces.

WARNING: Use of controls, adjustments, or procedures other than what is specified in the User Manual may result in exposure to shock, electrical hazards, and/or mechanical hazards.

To learn more about safety instructions, see the Dell knowledge base article Safety Precautions When Working with Electronic and Electrical Equipment.

If the screen abnormality is not present in the built-in self-test mode, see the Dell knowledge base article How to Troubleshoot Display or Video Issues on a Dell Monitor.

If the LCD built-in self-test (BIST) diagnostic test passed, the laptop LCD screen is working correctly. The display problem could be due to an outdated graphics driver or incorrect video settings. Follow the troubleshooting instructions in the Dell knowledge base article How to Troubleshoot Display or Video Issues on a Dell Laptop.

Get a range of wholesale laptop screen tester designed for different testing needs. For those involved in the field of digital electronics and who need to work with digital circuits and systems regularly, consider the wide range of logic analyzers that are available. Quality testing equipment will be able to help verify and debug your digital designs efficiently when required.

If you are looking for items like electric tester pens for personal or home use, pick from the range of voltage detector kits available. For those who do not require an entire kit, look into the individual product listings for the different types of pen voltage testers that are on sale instead.

For owners of electronic tools and equipment supply stores, there is also a large variety of testing equipment that you might want to consider purchasing. Products that are available include vector network analyzers, circuit breaker testers, megohmmeters and even tube testers. Get laptop screen tester from several popular and leading brands here.

If you happen to be in search of an affordable tool for troubleshooting purposes, consider equipment like the amp clamp meter for quick and effective checking. For those looking for more specialized products, like tools to test fiber optic cables, look into the selection of quality optical time-domain reflectometers, also known as the OTDR, which are used to test the integrity of fiber cables.

Check the extent to which your monitor can display similar colors while keeping them differentiable. You can create two color patches to do so. The more similar the two colors that can still be differentiated from one another are, the better your monitor can differentiate between the colors. This test is also well suited for making a direct visual comparison between two different monitors.

Choose a greater viewing distance to check the display of gradients. The grayscale image should be reproduced in the overall view without any unnecessary color and with an even gradient, and, at 256 intervals, there should not be any noticeable abrupt changes in brightness between individual grayscales. At a smaller number of intervals, the respective bars should be clearly differentiable from one another.

This test allows you to determine whether your monitor can reproduce text sharply and without any shadows, independently of other influences, such as text smoothing.

Test the monitor’s viewing angle stability. When you increase the viewing angle, the size and shape of the circles displayed should remain almost the same. Slight changes may appear. Less is better.

Use the slide bar to change the logo’s grayscale until the logo blends into the background to the greatest possible extent. The value shown corresponds to your monitor’s gamma value.

This test primarily serves to compare the response times of two monitors. Start by selecting a speed that creates clear streaks on the rectangles. However, you should still be able to clearly follow the rectangles visually. Then vary the distance between the rectangles until the lower edge (streak) of the one on the right no longer overlaps the lower edge of the one on the left. The smaller the distance, the shorter the response time. When comparing several monitors, select the same speed.

@jesse, I"ve only done it a few times but haven"t had any unpleasant collateral damage. (I"m a small home-based shop, not a store front.) Usually, I have some defective screens that still show a partial image, or at least light up if the screen shows no image. For CCFL screens, I have a tester that illuminates the screen if it or the inverter is not burned out but as @NEWTWizz says, most screens are LCD now so it rarely gets used any more.

I don"t stock commonly used screens because they end up sitting around forever, but there is a thread on TN of which screens are most popular and worth stocking. If I did, I"d probably use one of them. Too bad about your rotten luck with that screen zapping something but I know of no way to know whether that might happen with any give test screen. I"m sure the major screen distributors like laptopscreens.com have a program that could tell you whether the test screen will be compatible with a given make/model laptop but that"s no accessible to us, unfortunately.

Looking for a quick and easy way to test your LCD or display screen? Look no further than our LCD test tool! This convenient online tool is designed to help you check your display screen for any issues, including dead pixels or existing pixels that aren"t working correctly.

Our LCD test tool features a range of primary colors to help you quickly identify any potential issues with your display screen. Whether you"re using a laptop, desktop computer, or mobile device, our online tool makes it easy to check your LCD or display screen in just a few clicks.

So why wait? If you"re concerned about the health of your LCD or display screen, give our online LCD test tool a try today! It"s quick, easy, and completely free to use.

Once you have found the correct part number, see HP Consumer Notebook PCs - Ordering HP certified replacement parts. Use the instructions in this document to order a replacement part.

With more people spending more time in front of computer monitors it is important to purchase a quality monitor that will provide crisp, bright images, while reducing the strain on your eyes.

Users would include computer repair centers, system integrators, quality assurance personnel, graphic designers and anyone that cares about the quality of their monitor.

This website is using a security service to protect itself from online attacks. The action you just performed triggered the security solution. There are several actions that could trigger this block including submitting a certain word or phrase, a SQL command or malformed data.

To use this tool, you need to know screen voltage ,the resolution of the LCD/LED screen and the bit number of the LVDS cable for the panel, then check them against the list of screen parameter on the panel to find the right parameter and input it with the ”+” key and ”-” key on the panel digital tude.

A while back I was sitting around and wondering what to do with my dead laptop. I knew the mother board was fried but everything else was still in working condition. As a result, I decided to make an external monitor from my dead laptop and proceeded to do the research to find out if this was possible. Below is what I discovered. Unfortunately, there was no way to use the motherboard"s VGA connector. The VGA connector on a laptop is used to connect to an external monitor. In any case the VGA connector is output only and wouldn"t work for an external screen. As a result, I found that I needed to buy a controller board for the LCD screen, to make it work as an external monitor. This was the main cost but was still less than half the cost of buying an external monitor.

Disclaimer: Due note, I take no responsibility for your actions, implied or otherwise. I am not telling you to do anything, This instructable is informational.

Step one. Unplug the dead laptop from any power source AND remove the battery!. The laptop battery is located, usually, on the bottom and can be removed by sliding a release lever. These are lithium ion batteries and can hold a few Amps. The risk of shock might be minimal. However, there is no need to take the risk.

Step Two. To Remove the LCD screen from the laptop, you will need to remove the screws. There are rubber pads on the front of the LCD screen to protect it when the laptop lid is closed. Behind the rubber pads are the screws. Find and remove all the screws holding the front plastic frame on the laptop lid. Keep track of the pads and screws as you will need them to reassemble everything.

Step Three. Remove the plastic frame from the LCD screen. Here is where you need to be careful. The screws are not the only thing holding the plastic frame on the LCD screen! The plastic frame is snapped into place. Carefully pry loose the frame from the LCD screen. Pry it loose gently. Try to keep it as close as possible to the LCD panel while you are prying it loose because you may also find that you need to slide it to the left or right to completely remove it from the laptop. There is a small protrusion of the plastic frame where the hinge is. Because of this protrusion you need to slide the frame, in this case, to the right, to detach it from the laptop.

Step Four. Locate and remove the screws holding the LCD panel to the laptop. These are located on the bottom. The screws are attached to a small metal hinge. this is the component that is attached to the keyboard frame.

Next you will need to remove the LCD screen. Note that there is a cable attached. This is the LVDS cable. It is best to take apart the rest of the laptop and unplug it from the keyboard. However, the cable can be cut at the bottom. Take care not to cut the two wires going into the inverter (that"s the slim circuit board at the bottom.

Once the LCD panel is removed, you can remove the LVDS cable and unplug the inverter at the bottom. Unplug the inverter from both ends. Do not cut it. The LVDS cable is taped to the back of the LCD screen at the top. It is the flat cable running up the back. Remove the tape and slid the cable down. Since you need to buy an LCD controller board, you will no longer need the LVDS cable the laptop came with or the inverter. At this point you should just have an LCD screen with a pair of wires coming out of it.

Keep track of the plastic front frame and the plastic backing. You will need them to resemble the LCD screen. On the other hand, you have different fingers, just kidding. On the other hand, you can buy a picture frame and put the LCD screen in the picture frame.

Here is a picture of the LVDS cable and the inverter detached from the LCD screen. Since we will be buying an LCD control board these cables will not be needed again.

Next, once you have removed the LCD panel. Flip it over and look for a model number on the back. You will need this model number to order the correct LCD controller board. I went to E-Bay and found one for $42.00. I bought the LCD controller board and then received an email from the seller requesting the model number of the LCD screen and manufacturer. This is because each controller board is flashed, (programed to run a specific LCD) I gave him my model number, LP171WX2 A4K1 and told him it was made by LG Phillips. Since the board was coming from China, I received my order about 2 weeks later. Due note to buy one with a power cord! The LCD controller board has the VGA input connection which allows you to connect it to another computer and use it as a second monitor or as a back up in the event the one on your working computer goes out.

The LCD controller board is real easy to connect. It comes with all the required cables, except a VGA cable which you will need, in order to connect your LCD to another computer. You can buy a VGA cable from Best Buy or a computer parts store.

The LCD control Bard comes with all the cables except the VGA cable which you will have to buy. Once you have received your kit, proceed to connect it to the LCD screen. Plug the LVDS cable into the LCD panel where you removed the original from. The two wires at the bottom of the LCD screen that were connected to the inverter need to be unplugged from the old inverter and plugged into the new inverter below. Then, plug the power in. Make sure that the LCD control board is not sitting on anything conductive, like metal or it will short and fry. Next connect the VGA cable to the LCD control board and plug the other end of the VGA cable to another computer. Make sure the computer is on before you plug in the VGA cable. At this point you should have the same image that is on the computer you plugged the VGA cable into, on the LCD panel.

Next, I attached a 4 inch section of two by four on the outside back of the laptop lid. I needed this in order to attach my stand to the LCD screen. I used 5 screws and screwed them in place from the inside. I did splice and extend the cables going from the LCD controller to the inverter it came with just to have a little more room.

Originally, I built a nice wooden stand for my LCD panel but was not satisfied with it. So, I took a broken florescent desk lamp and dremeled off the section holding the florescent tubes, leaving enough metal to screw on to the two by four on the laptop lid. Before attaching the stand, I drilled four holes in the metal to make it easier to screw it on the two by four.

Next you will need to attach the LCD controller to the laptop lid. To do this, screw in a few sections of wood from the inside of the lid. Then on the outside of the lid attach the LCD control board. Place the wood in an area where the control board can reach.

Next you will need to find all those screws you have been saving and reassemble the LCD screen. I also added some surgical tubing to the top springs for added strength.

By the way a store bought swing arm half the size of this one, I found, cost around $400.00. If you choose to use a swing arm like this one, go with the one that has a magnifier on it and dremel off the magnifier leaving enough metal to attach to your LCD lid. You need one of this caliber to hold the LCD screen. Swing arms with the light attached are not strong enough.

By the way, I did remove the web cam from the laptop lid, wired it to a USB cable, and turned it into and external peripheral. I wired the two microphones that I found next to the web cam and  turned them into external peripherals. I dremeled the batteries open and wired them into a 3 million candle power flashlight made from spare parts I had. I have a lithium ion battery charger, so it worked great.

Since I was asked about the web cam, I though Should add it to the instructable. There is a nice instructable here at this site showing how to convert a web cam from an LCD screen: http://rntmns.com/2011/02/rebirth-of-a-webcam/

The web cam is now wired for plug and play. However, it only works on another computer running Windows Vista. There are no drivers for windows 7, yet. Since I don"t have Windows XP, I don"t know if it would work on it. Once you have wired it, open Skype on Vista and click on change profile pic. It will show two web cams in the drop down menu. If your web cam starts getting hot then you have revered the power cables.

Mine works great on my Vista laptop. If you want to use it for checking plumbing pipes, I suppose you can put a small prism on the web cam aperture so you can insert the web cam in a pipe and view images directly ahead--this would be good for archaeology where you need to investigate tight spaces.

I"m so glad I found this... I have a nearly identical HP laptop that you used and recently noticed that it was overheating and too much work to fix up, but the big beautiful display works great and I was sadly thinking I"d be better off selling it rather than dissecting the entire thing to fix its overheating issue.

Actually, you can do One better. You can salvage the RAM, the Wireless card, the Batteries, the charger, the hard drive, the DVD disk player and sell them to people that need them on E-bay and Still keep the LCD screen for yourself.

Very nice instructable. This instructable is the answer to a question that comes up about once a week in instructables questions and will get referred to often.0

The LVDS cable of the controller board is too short for the way I need it to be, does anyone know if there is an easy or inexpensive way to extend its lenght? (with LVDS cable I mean the 20/30 pin cable that is the main data cable for the display and goes to [in my case] 20 pin on the big board of the controller board)

Thanks for this instructable. I recently came upon some discarded laptops with either had bad screens or nonfunctioning everything else. I may be able to mix and match to get a usable machine out of the pile of junk!0

I checked ebay for the LCD control Board and all I did was punch in " LCD control Board for a LP154W01(A3)" , That"s my model number. You, of course, use your"s. ebay came up with the correct one for $25.00 and it has all the imputs you could want. This is good today, 2/11/19. Have fun folks!

i have a similar lcd panel to yours. infact 3 of them! they"re so easy to work with and doesn"t need a backlight controller LP154WH4 TLA1 except the lvds cable sold separately. I"ve build one and runs on

This would be great for the Flight Sim I am building, Problem is e-qstore can"t speak English. I bought 2 18.4 monitors after I ordered the controller, then they email me 2 days laster telling me they can"t make this control board. Been trying to find another board that will work with another monitor only to get "Sorry Sorry" and other things I can"t even make sense of.

Nicely done and very informative!! However unfortunately, by the time you add the cost of the LCD Controller card, various parts and time you could have bought a new inexpensive monitor.

it really depends on what kind of display your laptop came with. I recently had a laptop that featured a 4k OLED screen and If I add the price up of the controller kit and materials (depending how you are going to make the stand) it would actually in my case be cheaper to make that an external monitor because, quite frankly 4k is pretty expensive and I don"t want to degrade to a lower resolution. in said laptop the motherboard died so I just scavenged everything including the LCD which I have just lying on my desk. so I might even consider trying this.0

This website is using a security service to protect itself from online attacks. The action you just performed triggered the security solution. There are several actions that could trigger this block including submitting a certain word or phrase, a SQL command or malformed data.