admatec c-berry tft display made in china

The LCD module C-Berry designed by Admatec comes as a 3.5-inch diagonal TFT screen [1]. It also includes an adapter for the GPIO interface of the Rasp Pi, which makes it possible to integrate the hardware without much effort into your projects. The screen has an off-the-shelf price tag of about EUR 40 at dealers like Conrad or ELV Electronics.

The C-Berry module (Figure 1) can display 320 pixels horizontally and 240 pixels vertically. It emits a relatively strong 600 lumen, which means the visual display is easy to see even in daylight. At 5 volts, the module pulls about 350mA from the GPIO port and thus does not need its own power supply.

The LCD module comes in three parts: the basic TFT screen, an adapter for the GPIO port, and the connection cable that runs between the adapter and the screen. To put the parts together, you just connect the flat ribbon cable to both the screen and the adapter and then plug the adapter into the GPIO port. You need to make sure the ribbon cable is positioned correctly: Be sure the metal contact points on the cable point upward and away from the board when it is connected (Figure 2).

Alluvodna strankaRaspberry PiEnclosures Boxes CasesLCD TFT OLED Display for RPiAccessories Cables Power SuppliesmicroSD Memory Card & AdapterRaspberry PI Single-board ComputerCamera for Raspberry PiShield & Board for Raspberry PiWiFi for Raspberry PiKeyboard & Touchpad for Raspberry PiRaspberry Pi Kit Pack bundleRELAY BOARDGSM/GPRS/3G/4G/LTE/WiMax/5G/GSM BOARDS FOR RASPBERRY PIRaspberry Pi 400 (Pi400 RPI400)Raspberry Pi Compute ModuleRaspberry Pi PicoRaspberry Pi Zeromicro:bitmicro:bit KITArduinoBREAKOUT BOARDS, Accessories & CablesArduino KitOriginal ARDUINO BoardsOriginal ARDUINO ShieldsARDUINO BoardsARDUINO ShieldsARDUINO Box EnclosuresESP32 ESP8266Development Tools8051 Development ToolsMicrochip AtmelBREAKOUT BOARDS & SHIELDSARM Development ToolsCypress PSoC DevelopmentProgrammersData LoggersSTMICROELECTRONICSWeb ServerAndroid MINI PC / Development Kit.NET Micro FrameworkFPGA ALTERA Intel Xilinx Lattice Microchip CPLD ASICSingle board Linux computerJTAG ToolsMAXQ2000System On ModulesFREESCALEParallax Basic Stamp PropellerBeagleBoard BeagleBoneCubieboard Cubietruckx86 Vortex86Banana PiODROIDFTDI Chip’s FT90x, ..OLIMEXOnion (Omega2)Základné doskyAI - Deep Learning - Neural NetworkJetson (NVIDIA)SparkFun MicroModBIOMETRIC MEDICAL E-Health Sensor EEG EKGEnclosures Boxes CasesWearable electronic / E-TextilesPrototyping SADY STAVEBNICECompilers & SoftwareSingle Board ComputerMotor DriverElectronic Components / Battery / Memory cardM5StackMeasuring instrumentsDigital OscilloscopesSpectrum AnalyzersWaveform GeneratorsDigital MultimetersPower SuppliersUniversal CountersLogic AnalyzersLCR MeterPower MeterHandheld Digital MultimeterNon-invasive AC Current SensorData loggerData AcquisitionImaging IR ThermometerDC ELECTRONIC LOADS - Elektronická záťažLCD TFT OLED e-paper0.9 - 5" LCD display5 - 8" LCD display8 - 16" LCD displaye-Paper / E-INKOLED / AMOLEDCOG, VFD, Character/Monochrome LCDDisplay AccessoriesIoT (THE INTERNET OF THINGS)SONOFFComplete Robots3D Printer, Bluetooth Printer, Thermal PrinterGaming System ArcadeVyberame / WE LOVE TRENDUnipiNUMATO

Ah, I hadn"t spotted that pdf. It looks as if some electronics design work is required to interface the chip to the bare display. The device I chose had the benefit of being available with the electronics already integrated, including the voltage conversion, so all it needs is 3.3V and some GPIO lines. There is a fair amount of circuitry on the interface board http://repaper.org/doc/downloads/epd_re ... it_v05.pdf - I don"t know how typical that is. A reference design for the Ultra Chip and the display would be good.

I"d like to see a larger display. I"d also like one with a microcontroller on the interface board so that the rather convoluted timing could be offloaded from the Pyboard to the interface. Alas the Embedded Artists" one was the best I"ve found to date in terms of ease of interface.

As an aside there is something odd about the image on the display: it refers to the C-berry and Raspberry Pi and the manufacturer admatec. These references lead you to an entirely different TFT display. Make of that what you will...

The new line of 3.5” TFT displays with IPS technology is now available! Three touchscreen options are available: capacitive, resistive, or without a touchscreen.

For over 20 years Newhaven Display has been one of the most trusted suppliers in the digital display industry. We’ve earned this reputation by providing top quality products, services, and custom design solutions to customers worldwide.

This software is provided by Midas Displays in order to help users get started with the MDT0500D1OSC-PAR-KIT1, which is a development kit for 7 inch touchscreen display that works with Raspberry Pi.

This software is provided by Midas Displays in order to help users get started with the MDT0500D1OSC-PAR-KIT1, which is a development kit for 7 inch touchscreen display that works with Raspberry Pi.