5 lcd touch screen raspberry pi price

I"ve been looking around for a small HDMI LCD screen to use as a seconday screen with Windows and it took a few months of research on and off before deciding on the Elecrow 5" HDMI monitor. For the most part, it took me a while because a lot of reviews here and on other sites were primarily about use and config with Raspberry Pi.

Thanks to reviewer Alan who gave a good review with plenty of photos that convinced me to go for it. Not sure if it"s just how Amazon stores user review videos but the video review was a bit pixelated so it was hard to appreciate the clarity of the screen but it seemed to be what I was looking for.

Having used it for a few months now I still can"t believe how clear and sharp the screen is! There are sadly no controls for brightness, colour, saturation or contrast but everything displayed looks very nice and accurate.

Usually when you see the resolution 800x480 you think how bad that looks when your PC doesn"t have the right drivers installed and it looks blocky. I know it"s all relative and about DPI but once I had it all connected and tested it was sharp and clear, almost HD. I wish I had bought one sooner as it is exactly what I was looking for having tried a Lilliput monitor.

As I"m using this with Windows, I"ve not needed to look through the included driver utility disc and not tried the resistive touchscreen so I can"t comment on those. Windows just detects it as a second display and lets me extend my desktop. No drivers needed. The box contains the LCD screen, a HDMI bridge connector that neatly connects the HDMI socket on the top of the screen to the HDMI socket on the Raspberry Pi when mounted together. Standoffs for mounting are also supplied plus a plastic stylus.

+ It shows the video feed straightaway without any fancy splash screens or slow initialisation pauses. This was one of the annoyances with Lilliput monitor was a slow bright blue screen on power on before it would think about showing the feed. I know it"s only a few seconds but I specifically wanted instant feed on power on for future uses.

+ I was hoping for an on/off switch but no it only has a backlight switch which I wasn"t sure about to begin with but I"ve since found it very useful and better. I was thinking about buying a micro USB cable designed for Raspberry Pi with an inline power switch built in but for now the brightness switch is fine. As a blessing in disguise, it prevents Windows/DirectShow from blinking all screens when it realises a monitor has been disconnected, that blink would often cause the video on my TV app to freeze. Turning off backlight doesn"t cause DirectShow to have a fit.

+ Small and light enough that I have it attached to a gooseneck arm so can position it how I need. I was going to buy one of those mobile phone gooseneck arms but I kept reading reviews of some not even being able to cope with weight of a smartphone without drooping so I"ve used a photographic gooseneck clamp which is a bit overkill but no droop!

- The only negative I can think of is the availability or lack of screen cases with cutouts to suit the position of the HDMI and USB sockets on this. The Elecrow has its HDMI and USB socket at the top edge of screen and nearly all cases I have looked at are designed for screens with HDMI and USB on the right edge. I"ve had to import one from China that had the cutouts for this screen. Took about 2 weeks to arrive. Wish I"d have ordered two cases at the same time to avoid the wait as I"m impressed with the clarity of Elecrow I hope to buy another one in near future.

! Just one more thing Columbo! I had originally wanted to buy Revision B of this screen with capacitive touch screen because it has OSD menu buttons. I can"t find any manuals but I"m hoping that OSD buttons allows settings for brightness as that was my other preferred criteria. Having said that, I think it would be even more impossible to find suitable case due to the positions of sockets and extra menu buttons on Revision B screen. Maybe Elecrow could provide some insight on available cases?

※Price Increase NotificationThe TFT glass cell makers such as Tianma,Hanstar,BOE,Innolux has reduced or stopped the production of small and medium-sized tft glass cell from August-2020 due to the low profit and focus on the size of LCD TV,Tablet PC and Smart Phone .It results the glass cell price in the market is extremely high,and the same situation happens in IC industry.We deeply regret that rapidly rising costs for glass cell and controller IC necessitate our raising the price of tft display.We have made every attempt to avoid the increase, we could accept no profit from the beginning,but the price is going up frequently ,we"re now losing a lot of money. We have no choice if we want to survive. There is no certain answer for when the price would go back to the normal.We guess it will take at least 6 months until these glass cell and semiconductor manufacturing companies recover the production schedule. (Mar-03-2021)

All the accessories listed below tier pricing need to pay.We won"t deliver until you select. Power adaptor should be 5V/2000mA in output and center pin for positive voltage and the outer shield for negative voltage .The temperature for controller RTD2660 would increase during working.That"s normal phenomenon,not quality problem.

ER-TFTV050A1-1 is 480x272 dots 5" color tft lcd module display with small HDMI signal driver board,optional capacitive touch panel with USB controller board and cable and 4-wire resistive touch panel with USB driver board and cable, optional remote control,superior display quality,super wide view angle.It can be used in any embedded systems,car,industrial device,security and hand-held equipment which requires display in high quality and colorful video. It"s also ideal for Raspberry PI by HDMI.

All the accessories listed below tier pricing need to pay.We won"t deliver until you select. Power adaptor should be 5V/2000mA in output and center pin for positive voltage and the outer shield for negative voltage .The temperature for controller RTD2660 would increase during working.That"s normal phenomenon,not quality problem.

ER-TFTV050A1-4 is 800x480 dots 5" color tft lcd module display with small HDMI signal driver board,optional 4-wire resistive touch panel with USB driver board and cable, optional capacitive touch panel with USB controller board and cable, optional remote control,superior display quality,super wide view angle.It can be used in any embedded systems,car,industrial device,security and hand-held equipment which requires display in high quality and colorful video. It"s also ideal for Raspberry PI by HDMI.

Now we have this 5-inch TFT display with a touch screen that can provide a high-resolution picture and a large viewing screen for your Raspberry Pi. The display supports any revision of Raspberry Pi and works perfectly for Raspberry Pi B+/ 2B/ 3B. It is the low power consumption for the backlight of the screen. The high 800 x 480 resolution can give you a full-color experience, the touch screen allows users to play easily.

*When working with Raspberry Pi 4, for the system image of Raspberry Pi after 2021-10-30, for example on Bullseye, please modify "dtoverlay = vc4-kms-v3d" to "dtoverlay = vc4-fkms-v3d" in the config file, otherwise it may fail to start. But on Buster, please comment out "dtoverlay = vc4-fkms-V3D" by adding #.

The resolution of the LCD display is 800 x 480, you can configure the resolution via software, and the maximum resolution it supports is 1920 x 1080. It is a USB capacitive touch screen and does not require a driver. It supports five touch control, besides that, the LCD screen comes with an OSD menu adjustment function. You can adjust the contrast, brightness, and switch button. There are 9 interfaces on the back of the screen, one earphone for audio output; two touches (USB connector), for power supply and touch output; one display, an HDMI interface, for connecting the motherboard and LCD display. One power, it can control the backlight to turn on and turn off to save power. One return, it’s only useful in the OSD menu. One right/down, backlight shortcut key. One left/up, backlight shortcut key. A menu, it’s useful in the OSD setting menu, open the OSD/ select key.

*When working with Raspberry Pi 4, for the system image of Raspberry Pi after 2021-10-30, for example on Bullseye, please modify "dtoverlay = vc4-kms-v3d" to "dtoverlay = vc4-fkms-v3d" in the config file, otherwise it may fail to start. But on Buster, please comment out "dtoverlay = vc4-fkms-V3D" by adding #.

All orders are processedwithin 24 hoursafter they are placed. Usually, we are able to ship orders the next day. Weekend orders are shipped on the following Monday. You will receive a shipping confirmation email from our system when the shipping information has been uploaded.

Generally, we will ship the orders with Free Shipping, without the minimum order amount requirement. You may check if the free shipping method is available to your country in the Delivery Area below.

As soon as your order is packed and shipped, you"ll receive a shipping confirmation email. You will then be able to track your order through the tracking link on the email. If you haven"t received an email yet, please reach out to us atservice@sunfounder.com, our sales staff will contact you ASAP.

* Delivery Time - These are the delivery estimates provided by our shipping partners and apply from point of dispatch, not from point of sale. Once your parcel leaves our warehouse, we cannot control any delays after that point.

Compatible and Direct-connect with any revision of Raspberry Pi. (If you are using a Raspberry Pi Zero / Zero 2 W, an additional HDMI cable is required).

Raspberry Pi leads out 40 GPIO pins, while the screen leads out 26 pins. When connecting, pay attention to the corresponding pins and Raspberry Pi pins.

5) Insert the TF card into the Raspberry Pi, power on the Raspberry Pi, and wait for more than 10 seconds to display normally. But the touch is abnormal at that time, and the touch needs to be calibrated as the following steps.

3. After reboot, the touch will work normally under normal circumstances. But for different resistance screens, the accuracy of using the default calibration parameters may not be very suitable.

You can perform touch calibration by clicking the Raspberry Pi icon on the taskbar, selecting Preferences -> Calibrate Touchscreen, and following the displayed prompts.

4. After calibration, the following data will be displayed. If you want to save these touch values, you can replace the data in the red circle with the data in the corresponding position in 99-calibration.conf.

Since the ads7846.dtbo provided by Raspberry Pi by default has no de-jitter parameters, you can increase the de-jitter parameters by modifying and replacing ads7846.dtbo

The installation of xserver-xorg-input-evdev and xinput-calibrator in Ubuntu system reports an error, so the touch cannot be used normally. How to solve it?

The installation of xserver-xorg-input-evdev and xinput-calibrator in Kali system reports an error, so the touch cannot be used normally. How to solve it?

Waveshare 20109 - 5inch Capacitive Touch Screen LCD (H) Slimmed-Down Version, 800×480, HDMI, Toughened Glass Panel, Low Power Consumption - 5inch HDMI LCD (H) V4

Inky wHAT is a 400x300 pixel electronic paper (ePaper / eInk / EPD) display for Raspberry Pi, a larger version of our popular Inky pHAT display, with more than 5x the number of pixels, and available in three colour schemes - red/black/white,...

A high-resolution 8", IPS, 1024x768, HDMI display, with Pimoroni-made display driver board and keypad, that"s perfect for building into projects like arcade cabinets, or just use it as a handy display for your Raspberry Pi!

Build a full-featured media center capable of playing nearly all of your digital media using any 40 pin Raspberry Pi and the Media Center HAT Raspberry Pi touchscreen display. Native support in...

Inky wHAT is a 400x300 pixel electronic paper (ePaper / eInk / EPD) display for Raspberry Pi, a larger version of our popular Inky pHAT display, with more than 5x the number of pixels - red/black/white version.

If you"re looking for the most compact li"l color display for a Raspberry Pi B+, Pi 2, & Pi 3 (most likely a Pi Zero) project, this might be just the thing you need!

In honour of Raspberry Pi"s 10th birthday, we"ve fused a RP2040 microcontroller with an EPD display to make a stylishly monochrome, maker friendly, e-paper badge(r)...

Pico Inky Pack features the speedy 2.9" e-paper display that you can find on Badger 2040, coupled with three handy buttons for interfacing. Equip it to the back of your...

In order to meet the increasing need of compact HDMI displays, especially for some popular single-board computers like the Raspberry Pi, the UCTRONICS team now releases a 5-inch HDMI LCD display with capacitive multi-touch touchscreen

I got a chance to test this Raspberry Pi 5” TFT capacitive screen a while ago but I was busy all the time. Finally, I have some free time lately. This day I was on the MediaPipe site and just found the “MediaPipe Iris” function. Although the Python version of MediaPipe does not support Iris tracking, it doesn’t bother me. I decided to give it a try!

*When working with Raspberry Pi 4, please comment out by adding # in the front of "dtoverlay = vc4-fkms-V3D" or delete this line directly in the config.txt file.

The official Raspberry Pi 7” Touchscreen allows you to add touch inputs to your programs, creating a new way to interact with your projects. It also makes for a fantastic desktop screen for day-to-day use of your Raspberry Pi. Wrap it in one of our screen cases and take it anywhere – events, Raspberry Jams or even just your friends house for a coding evening!

For smaller projects, LCD and ePaper displays are a fun way to add a visual element to your projects. With simple code and wiring, they’re great for projects that require text, menus and navigation.

You can have peace of mind knowing that Raspberry Pi is backed by a 1-year warranty, and thanks to rigorous quality assurance testing in the UK factory, you can be sure that your Raspberry Pi will stay in good working condition.