7.0 40 pin tft display 800x480 with touchscreen made in china

This 7.0" TFT screen has lots of pixels, 800x480 to be exact, an LED backlight and a resistive touchscreen overlay. Its great for when you need a lot of space for graphics or a user interface. These screens are commonly seen in consumer electronics, such as miniature TV"s, GPS"s, handheld games car displays, etc. A 40-pin connector has 8 red, 8 green, and 8 blue parallel pins, for 24 bit color capability.

This is a "raw pixel-dot-clock" display and does not have an SPI/parallel type controller or any kind of RAM. The display is supposed to be constantly refreshed, at 60Hz, with a pixel clock, V sync, H sync, etc. There are some high end processors such as that used in the BeagleBone that can natively support such RGB TTL displays. However, it is extremely rare for a small microcontroller to support it, as you need dedicated hardware or a very fast processor such as an FPGA. Not only that, but the backlight requires a 125-150mA constant-current mode boost converter that can go as high as 9V instead of our other small displays that can run the backlight off of 5V.

For that reason,we are carrying it as a companion to the Adafruit RA8875 driver board in the store, which is a chip that can handle the huge video RAM and timing requirements, all in the background. That"s the best way to interface this display to just about any microcontroller(including Arduino & friends)If you want to control with from an HDMI or DVI output, check out our TFP401 driver board.

To create extra value for customers is our enterprise philosophy; buyer growing is our working chase for 40 Pin Tft Display, Tft In Display, Monochrome Tft Display, Rugged Touch Screen Monitor,Tft Computer Monitor. Safety as a result of innovation is our promise to each other. The product will supply to all over the world, such as Europe, America, Australia,Manila, Swaziland,Anguilla, Algeria.We will not only continuously introduce technical guidance of experts from both home and abroad, but also develop the new and advanced products constantly to satisfactorily meet the needs of our clients all over the world.

138 21 inch tft lcd touch screen module products are offered for sale by suppliers on Alibaba.comAbout 81% % of these are lcd modules, 14%% are lcd touch screen, and 1%% are touch screen monitors.

WF70A2TIAGDNT0 is a 7" TFT-LCD with RTP touch screen display module, made of resolution 800x480 dots. This module is built in with ST5623D and ST5091D driver IC, it supports 24-bit RGB interface. The brightness of WF70A2TIAGDNT0 module is 250 nits typical value, contrast ratio 800:1 (typical value), view direction 12 o"clock, gray scale inversion direction 6 o"clock, glare surface glass.

This 7.0" TFT screen has lots of pixels, 800x480 to be exact, an LED backlight and a resistive touchscreen overlay. Its great for when you need a lot of space for graphics or a user interface. These screens are commonly seen in consumer electronics, such as miniature TV"s, GPS"s, handheld games car displays, etc. A 40-pin connector has 8 red, 8 green, and 8 blue parallel pins, for 24 bit color capability.

This version has a 4-wire resistive touchscreen attached It"s exactly the same TFT display as PID 2353 but with a resistive touch panel so it is a little more expensive.

This is a "raw pixel-dot-clock" display and does not have an SPI/parallel type controller or any kind of RAM. The display is supposed to be constantly refreshed, at 60Hz, with a pixel clock, V sync, H sync, etc. There are some high end processors such as that used in the BeagleBone that can natively support such RGB TTL displays. However, it is extremely rare for a small microcontroller to support it, as you need dedicated hardware or a very fast processor such as an FPGA. Not only that, but the backlight requires a 125-150mA constant-current mode boost converter that can go as high as 9V instead of our other small displays that can run the backlight off of 5V.

For that reason, we are carrying it as a companion to the Adafruit RA8875 driver board in the store, which is a chip that can handle the huge video RAM and timing requirements, all in the background. That"s the best way to interface this display to just about any microcontroller (including Arduino & friends) If you want to control with from an HDMI or DVI output, check out our TFP401 driver board. If you are an advanced electronics enthusiast you can try wiring this directly to your processor, but it we don"t have any support or tutorials for that purpose.

ER-TFT070A2-4 is the updated part number of ER-TFT070-4. It"s 800x480 dots 7" color tft lcd module display with ILI6122 driver ic,optional capacitive touch panel with controller and connector,optional 4-wire resistive touch panel screen with connector,superior display quality,super wide view angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO, ARM and Raspberry PI.Equivalent with AT070TN90,AT070TN92.

It can be used in any embedded systems,car,mp4,gps,industrial device,security and hand-held equipment which requires display in high quality and colorful image.It supports rgb interface. FPC with zif connector is easily to assemble or remove.