banana pi lcd touch screen free sample

Insert the TF Card to Raspberry Pi, connect the Raspberry Pi and LCD by HDMI cable; connect USB cable to one of the four USB ports of Raspberry Pi, and connect the other end of the USB cable to the USB port of the LCD; then supply power to Raspberry Pi; after that if the display and touch both are OK, it means drive successfully (please use the full 2A for power supply).

After execution, the driver will be installed. The system will automatically restart, and the display screen will rotate 90 degrees to display and touch normally.

HyperPixel 2.1 Round has all the great features of our other HyperPixels - crisp, brilliant IPS display, touchscreen, and high-speed DPI interface—it"s just rounder! You can use it with any Raspberry Pi with a 40 pin header* but it works particularly nicely with the Pi Zero footprint - we"ve designed it so you can mount a Zero neatly behind it, so you can"t see the Pi when you look at it from the front.

This version of HyperPixel would be great for custom interfaces and control panels - mounted on a wall it would make a really neat, minimalist smart home controller or a stylish "what"s playing" display for your sound system. Everything is pre-soldered and ready to go, just pop it onto your Pi, install our software, and away you go!

* Please note that standoffs and booster headers are not included with Hyperpixel Round - scroll down or check out the extras tabs for some links. You will need a booster header if you want to use Hyperpixel Round with a full size Pi!

HyperPixel 2.1 Round uses a high-speed DPI interface, allowing it to shift 5x more pixel data than the usual SPI interface that these small Pi displays normally use. It has a 60 FPS frame rate and a resolution of approximately 229 pixels per inch (480x480px) on its 2.1" display. The display can show 18-bits of colour (262,144 colours).

The touchscreen variant is capacitive touch, that"s more sensitive and responsive to touch than a resistive touch display, and it"s capable of multi-touch!**

Hyperpixel Round will work with any 40-pin version of the Pi, including Pi Zero and Pi Zero W. If you"re using it with a full-size Pi then you"ll need a booster header to raise it up over the Pi"s USB ports and extended standoffs if you"d like to bolt it in place. If you"re using a Pi Zero or Pi Zero W you won"t need a booster header, but we have some special short standoffs that will let you attach everything securely together in an extra slim package.

If you"re using standoffs to fasten your Hyperpixel and your Pi together, just screw them into the posts on the underside of the HyperPixel PCB and then secure with screws through the mounting holes on your Pi.

Please note: when installing HyperPixel 2.1 Round onto your Pi make sure not to press down on the screen surface. We recommend putting the screen face down on a soft surface and gently wiggling the Pi to mate with the extended header (or GPIO header). If you need to remove your Hyperpixel, take care not to pull on the edges of the glass display - it"s best to hold on to the rectangular PCB. As the glass edges of this display overhang the PCB they"re quite exposed, so it"s worth being extra careful with them.

With this version of HyperPixel, we"ve separated the display drivers and touch drivers which should hopefully make it easier to incorporate touch interfaces into your own programs. To download and install the display drivers:

Note that you"ll need another display, keyboard, and mouse to install the software, or you could do it remotely over SSH if you set your Pi up headlessly.

HyperPixel uses basically all of the GPIO pins o communicate with the Pi (including the standard I2C pins) so it"s not generally possible to use it with other HATs and devices that connect via the GPIO...

...but we have provided an alternate I2C interface broken out on the back that will let you use I2C devices (like sensor breakouts) at the same time as HyperPixel. There are instructions how to set this up in our Hyperpixel 4.0 tutorial (scroll down to the bottom).

Raspberry Pi OS Bullseye includes major changes to how DPI display drivers work - a quick hack to get the screen working (with some loss of rotation/touch functionality) is to comment out dtoverlay=vc4-kms-v3d in boot/config.txt. We"re working on full support for Bullseye, but if you"re after an easy, fully featured Hyperpixel experience you should probably stick with Buster for now:

The resolution of the LCD display is 800 x 480, you can configure the resolution via software, and the maximum resolution it supports is 1920 x 1080. It is a USB capacitive touch screen and does not require a driver. It supports five touch control, besides that, the LCD screen comes with an OSD menu adjustment function. You can adjust the contrast, brightness, and switch button. There are 9 interfaces on the back of the screen, one earphone for audio output; two touches (USB connector), for power supply and touch output; one display, an HDMI interface, for connecting the motherboard and LCD display. One power, it can control the backlight to turn on and turn off to save power. One return, it’s only useful in the OSD menu. One right/down, backlight shortcut key. One left/up, backlight shortcut key. A menu, it’s useful in the OSD setting menu, open the OSD/ select key.

*When working with Raspberry Pi 4, for the system image of Raspberry Pi after 2021-10-30, for example on Bullseye, please modify "dtoverlay = vc4-kms-v3d" to "dtoverlay = vc4-fkms-v3d" in the config file, otherwise it may fail to start. But on Buster, please comment out "dtoverlay = vc4-fkms-V3D" by adding #.

This product supports Windows 10/8.1/8/7 OS.：1. Connect the TOUCH interface of LCD to the USB interface of PC . Waiting for a moment, The touch will be recognized by Windows automatically2. If you use HDMI, you need to connect the HDMI interface of LCD to the HDMI port of PC. About 5s later, you can see that the LCD display properly. If you need the audio, if you insert a 3.5mm earphones to HP ports.3. Use VGA,you need to connect the VGA interface of LCD to PC"s VGA ports byMini HDMI to VGA CableNote:1) If multi screen are connected to one PC at the same time, you can only control the cursor by this LCD, so please set the LCD as main screen.2) Some of PC cannot support HDMI screen Hot Plug . In this case, restart the PC can solve.3) Sometimes LCD will flicker because of undersupply from USB cable of PC. You need to connect an external power supply (5V/2A) to DC port.4) HP audio output only works while using HDMI communication5) Mini HDMI to VGA Cable is necessary and need to be purchased separately if you use VGA communication.

Some users want to connect more than one display to their PC. Here we talk about how to setting the touch to make the touchscreen to control its screen separately.Connect touchscreen to PC. Here we use an standard PC monitor and connect an 7inch HDMI LCD (C) for example. We make the monitor as main screen and the touchscreen as secondary screen.

If we want the touch of the touchscreen to control the desktop of the touchscreen itself. Just press Enter key to pass the first screen. And the second screen, when you find that the black text is displayed on the touchscreen, just touch the center of the touchscreen to finish this setting.After this setting, the touch on the screen will just control this touchscreen even thought it is not the main screen.

1 If the first screen and the second screen are touchscreen as well, you can touch them when the text is displayed on the screens. Then you can find that all the touchscreen can work.

When working with Raspberry Pi, you should set the resolution of the LCD by yourself, or else the LCD screen will not work. For more detail information, please read the following section.

Download the Raspbian image from Raspberry Pi web site. Write the image to a TF card and append the following lines to the config.txt file which is located in the root of your TF card:max_usb_current=1

For Pi Zero / Zero W: if you"ve used an SD card on a Pi 3 and then attached the card to the Pi Zero, the touch screen often doesn"t work. In such cases, you have to write a fresh system image to the SD card. The first boot up must be done on the Pi Zero but not Pi 3, due to initialization for a corresponding device.

With the operation above. The screen could rotate in display. However, the touch works improperly. To rotate the touch as display, you could do as below:

To work with Jetson Nano Developer Kit, you just need to connect the LCD and power onConnect the Touch interface of the LCD to USB port of Jetson Nano

Connect the USB Touch interface on the LCD to the USB interface on the BeagleBone board with a type-A-to-micro USB cable. (BeagleBone has two USB interfaces, one for host and the other for client. In here, you should connect the LCD module to the USB host interface).

Before powering up the Banana Pi, you should connect it to a LCD displayer properly, since the Banana Pi may read the resolution parameters of the LCD displayer on startup. And the connection should be remained till the Banana Pi enters the desktop. In this case, even if you disconnect the LCD displayer and reconnect it again to the Banana Pi, the LCD can still work properly.

Comparing with the Banana Pi, the BananaPi Pro has added an on-board WiFi module. When using the BananaPi Pro, you can use SSH to connect to the Pi and execute the following command to load the WiFi driver:sudo modprobe ap6210

Program the image file 7inch HDMI LCD (H)Lubuntu Imagewith password u00b to the board. This image file supports the modules BananaPi Pro and BananaPi. User name: bananapi Password: bananapi

CONS: low refresh rate & resolution, supports Raspberry Pi only, requires Raspberry Pi 40PIN GPIO (the SPI bus), poor compatibility with Raspberry Pi system.

PROS: high refresh rate, multiple resolution support, multiple devices support, leaves the Raspberry Pi 40PIN GPIO free, better compatibility with Raspberry Pi system.