2.8 tft display with resistive touchscreen for sale

ER-TFTM028-4 is 240x320 dots 2.8" color tft lcd module display with ILI9341 controller board,superior display quality,super wide viewing angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO,ARM and Raspberry PI.It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.

It supports 8080 8-bit /9-bit/16-bit /18-bit parallel ,3-wire,4-wire serial spi interface.Built-in optional microSD card slot, 2.8" 4-wire resistive touch panel with controller XPT2046 and 2.8" capacitive touch panel with controller FT6206. It"s optional for font chip, flash chip and microsd card. We offer two types connection,one is pin header and the another is ZIF connector with flat cable mounting on board by default and suggested. Lanscape mode is also available.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!".Here is the link for 2.8"TFT Touch Shield with Libraries, EXxamples.Schematic Diagram for Arduino Due,Mega 2560 and Uno . For 8051 microcontroller user,we prepared the detailed tutorial such as interfacing, demo code and development kit at the bottom of this page.

ER-TFT028-4 is 240x320 dots 2.8" color tft lcd module display with ILI9341 controller and optional capacitive touch panel and 4-wire resistive touch panel,superior display quality,super wide viewing angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO ARM and Raspberry PI.It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.It supports 8080 8-bit,9-bit,16-bit,18-bit parallel,3-wire,4-wire serial spi interface. FPC with zif connector is easily to assemble or remove.Lanscape mode is also available.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!".Here is the link for 2.8"TFT Touch Shield with Libraries, Examples.Schematic Diagram for Arduino Due,Mega 2560 and Uno . For 8051 microcontroller user,we prepared the detailed tutorial such as interfacing, demo code and development kit at the bottom of this page.

Orient Display offers many types of standard resistive touch panels. All of them are low cost 4 wire types. We can also custom made 5 wires or 8 wires resistive touch panels. The connection of resistive touch panels are mostly FPC. Orient Display can provide resistive touch panels separately or integrated with LCD displays. The standard resistive touch panels include, 1.44”, 1.77”, 2.0”, 2.2” , 2.4”, 2.8”, 3.0”, 3.5”, 4.3”,5.0”, 7.0”, 8.0”, 10.1”, 12.0”, 14” , 15.6” etc. with different aspect ratio. Please contact: Sales Inquiries, Customer Service or Technical Support for more details and availability.

The history of resistive touch panels starts in the 1970s. For years, that was the most common touch input technology. But it has been quickly replaced by CTP (capacitive touch panels) especially the emerge and development of iPhone starting 2007.

The resistive touchscreen consists of a glass layer with a conductive coating on top and a polyester top sheet with a conductive coating on the bottom. The conductive surfaces are held apart by “spacer dots”, usually glass beads that are silk-screened onto the coated glass. On a 5-wire resistive design (the most commonly used kind of resistive screen in large format POS applications), a voltage is applied to the 4 corners of the glass layer. When a person presses on the top sheet, its conductive side comes in contact with the conductive side of the glass, effectively closing a circuit (this is called pressure sensing). The voltage at the point of contact is read from a wire connected to the top sheet.

If you have any questions about Orient Display resistive touch panels. Please feel free to contact: Sales Inquiries, Customer Service or Technical Support.

Spice up your Arduino project with a beautiful large touchscreen display shield with built in microSD card connection. This TFT display is big (2.8" diagonal) bright (4 white-LED backlight) and colorful (18-bit 262,000 different shades)! 240x320 pixels with individual pixel control. It has way more resolution than a black and white 128x64 display. As a bonus, this display has a resistive touchscreen attached to it already, so you can detect finger presses anywhere on the screen.

We"ve updated our original v1 shield to an SPI display - its a tiny bit slower but uses a lot less pins and is now much easier to use with Mega & Leonardo. We also include an SPI touchscreen controller so you only need one additional pin to add a high quality touchscreen controller. Even with all the extras, the price is lower thanks to our parts sourcing & engineering skillz!

The shield is fully assembled, tested and ready to go. No wiring, no soldering! Simply plug it in and load up our library - you"ll have it running in under 10 minutes! Works best with any classic Arduino (UNO/Duemilanove/Diecimila). Solder three jumpers and you can use it at full speed on a Leonardo or Mega as well.

This display shield has a controller built into it with RAM buffering, so that almost no work is done by the microcontroller. This shield needs fewer pins than our v1 shield, so you can connect more sensors, buttons and LEDs: 5 SPI pins for the display, another pin for the SPI touchscreen controller and another pin for uSD card if you want to read images off of it.

• The display uses digital pins 13-9. Touchscreen controller requires digital pin 8. microSD pin requires digital #4. That means you can use digital pins 2, 3, 5, 6, 7 and analog 0-5. Pin 4 is available if not using the microSD

This is a very nice 2.8" TFT Color LCD 240 x 320 pixel with Touch Screenscreen display module. It has an embedded ILI9325 graphics controller and on-board AD7843 touch screen controller that delivers standalone functionality to any project. It is easy to use.

Raystar ‘s Resistive Touch Screen TFT Display uses 4- wire type of resistive touch screen with advantages of low-power consumption, fast response time and stable quality. With full ranges from small to medium sizes, we set low MOQ in standard products. Comparing to TFT Capacitive Touch screen Display, the Resistive Touch Screen TFT is more competitive.

The resistive structure is sensed by pressure so there is no limitation of contacting forms. Resistive touch screens work smoothly even using a pen or with gloves. TFT display with resistive touch screen can be used on consumer electrical products, such as POS system, security system, control monitors and GPS devices.

With four bright white LED backlight and 240 x 320 pixels with individual RGB pixel control, this colour 2.8in. TFT display features a resistive touchscreen for fingertip detection across the entire screen surface. The workload is lifted from the microcontroller by a built-in controller equipped with RAM buffering, and the display board has two modes: 8-bit and SPI.

Add some jazz & pizzazz to your project with a color capacitive touchscreen LCD. This TFT display is big (2.8" diagonal) bright (4 white-LED backlight) and colorful! 240x320 pixels with individual RGB pixel control, this has way more resolution than a black and white 128x64 display. As a bonus, this display has a capacitive single-touch touchscreen attached to it already, so you can detect finger presses anywhere on the screen. (We also have a resistive touchscreen version of this display with a breakout)

This is a screen for advanced hackers who like the look of the TFT screen we"ve put into the PiTFT, TFT shield v2 and 2.8" TFT breakout with capacitive touch. This display has 320x240 pixels and is driven with the ILI9341 chipset. The touch chip is a FT6236 which communicates over I2C. This is just the display module! No PCB is included! You can talk to this chip with SPI (4 or 3 wire), 8 bit parallel, or 16 bit parallel. It also can be put into "dot clock mode" for raw TTL signal in but we have never done this ourselves so there"s no example code for that.

We"re selling this module bare for those who want to integrate it into their own project. If this is your first time working with this TFT we suggest our breakout board which makes it easy to use SPI or 8-bit interfacing and also has mounting holes, level shifting, etc.. For the TFT command set, the data sheet is very complete, but we also have some Arduino code you can refer to here to get started

Nextion is a Human Machine Interface （HMI） solution combining an onboard processor and memory touch display with Nextion Editor software for HMI GUI project development.

Using the Nextion Editor software, you can quickly develop the HMI GUI by drag-and-drop components (graphics, text, button, slider, etc.) and ASCII text-based instructions for coding how components interact on the display side.

Nextion HMI display connects to peripheral MCU via TTL Serial (5V, TX, RX, GND) to provide event notifications that peripheral MCU can act on, the peripheral MCU can easily update progress, and status back to Nextion display utilizing simple ASCII text-based instructions.

Although DHL service is partly recovered, there are still issues with on-time delivery. Postal services get delayed by around 30-45 days in many countries.